HAVIT Lighting HV2826W Flame Deck Light Instruction Manual
- June 4, 2024
- Havit Lighting
Table of Contents
HAVIT Lighting HV2826W Flame Deck Light
Flame Deck Light Installation Instructions
| Product Specifications | Dimensions |
|---|---|
| Model No. | HV2826W |
Name| Flame
Material| 316 Stainless Steel
Colour| Stainless Steel
IP Rating| IP67
Input Voltage| 240V – Driver | 12v DC Fittings| 12V DC
Protection Class| Driver Fitting Low Voltage| Low Voltage
Lamp Base| Built in LED| Built in LED
Lamp Wattage| 6x 0.5w| 1x 0.5w
Colour Temp| 3000k| 5500k| RGB| 3000k| 5500k| RGB
Lumens| 6x 40lm| 6x 50lm| 6x 25lm| 40lm| 50lm| 25lm
CRI| > 80
Wiring| Parallel
Dimmable| No
Warranty| 3 Years Replacement*
Single Colour Wiring Diagram| RGB Wiring Diagram
|
Important Safety Issues
- This product must be installed by a qualified electrician according to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installation.
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required, if not within this allowance warranty will be voided.
- All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting.
- Warranty does not cover Tea Staining
- All o-rings and seals must be in place correctly to maintain warranty
- This form may be updated at any time due to product improvements, please check online installation form for most current version.
Steps for Installation
Single Colour Models
- Make sure that the electrical circuit is free of voltage (master switch off.
- Make a hole where fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
- Using an appropriate 12v DC LED Driver or if installing kit, use LED Driver supplied.
- DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- Connect the cable by connecting male plug from fitting to 4 metre extension cable from LED Driver.
- Insert fitting into hole
- Repeat steps 4 + 5 until all fittings are installed
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
RGB Models
- Make sure that the electrical circuit is free of voltage (master switch off )
- Make a hole where fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
- Using an appropriate 12v DC LED Driver or if installing kit, use LED Driver supplied .
- DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- Connect RGB Controller to LED Driver
- Connect the cable by connecting male plug from fitting to 4 metre extension cable from RGB Controller.
- Insert fitting into hole
- Repeat steps 5 + 6 until all fittings are installed
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Must be installed by a licensed electrician
Contact Details
143 Beauchamp Road Matraville NSW 2036 Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au
Warranty Terms & Conditions
Additional Information
Documents / Resources
|
HAVIT Lighting HV2826W Flame Deck
Light
[pdf] Instruction Manual
HV2826W, HV2826C, HV2826RGB, HV28261W, HV28261C, HV28261RGB, Flame Deck Light,
HV2826W Flame Deck Light, Deck Light
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>