sbs TESPEARMOOVEBTK Wireless Earphones User Manual
- June 9, 2024
- sbs
Table of Contents
sbs TESPEARMOOVEBTK Wireless Earphones
SPECIFICATION
Wireless: V 5.0
Impedance: 16Ω
Working Range: 10m
Frequency Range: 18Hz-20kHz
Sensitivity: 98dB
Input: 5 V D.C. 1A
Battery Capacity: 80mAh
Microphone
Music & Phone Calls
Charge Port: Micro-USB
Standby Time: 50 hours
Work Time: 6 hours
PRF: 6 mW max
f: 2402 + 2480 MHz
Overview
On the right “R” headset there is:
- Micro USB port for power cable connection;
- LED indicator;
- Microphone;
- MFB multi-function panel (ON/OFF – Bluetooth association – play/ pause – answer/end call – call/reject – call/call last number;
- “+” button (Volume up – next track);
- “-” button (Volume down – previous track).
Recharging information
- insert the power cable with the micro USB side into the headphones;
- insert the cable with the USB side into a computer or USB charger (not included);
- the red LED lights up during charging;
- a complete recharge takes about 2 hours;
- the red LED turns off when the charging is complete.
Connecting the headphones
- Press and hold the MFB button (centre – multifunction button) for 5 seconds until the LED flashes alternately in Red/Blue – you will hear “Power ON”.
- Activate the phone’s Bluetooth, search and select the SBS Runner Flexy 2.0 headphones to connect with – you will hear “Connected”.
- Once the headphones are connected to the phone, under normal conditions the LED will slowly flash blue.
IMPORTANT:
after carrying out the connection procedure for the first time, for subsequent
connections with the same phone, just hold down the MFB button (for 5
seconds); the LED will flash alternately in Red/ Blue – you will hear “Power
ON” and immediately afterwards you will hear “Connected”: the headphones will
then be connected automatically (LED slowly flashing Blue).
USING THE HEADPHONES
Switching on/Connecting:
Switch on the headphones by pressing the MFB button (central – multifunction button) for 5 seconds until the red/blue LEDs flash alternately – you will hear “Power ON” – the headphones are now ready to connect with the smartphone.
Switching off:
press and hold the MFB button for 5 seconds until the red/blue LED flashes alternately for 2 seconds and then goes off. – you will hear “Pairing Power OFF”
Answering a call:
Press the MFB key quickly once to answer an incoming call.
Ending a call:
Press the MFB button quickly once to hang up.
Reject a call:
long press (about 3 seconds) the MFB key to reject a call.
Call the last number: double-click on the MFB button.
+ Button:
Long press the “+” button to increase the volume.
Press the “+” button for one second to play the next song.
– Button:
Long press the “-” key to lower the volume.
Press the “-” button for one second to play the previous song.
Play / Pause: press the MFB button once quickly.
SAFETY PRECAUTIONS
-
Please read, follow and save these instructions.
-
Pay attention to all warnings on the product and instructions for use.
-
Stop using the product immediately if it causes discomfort or pain.
During use it is recommended to keep the volume at a level that is not harmful to your ears and allows you to hear the surrounding noises.
WARNING:
to prevent possible damage to the ears, do not listen at a high volume! -
Store the appliance away from heat, moisture and dust.
-
Do not use abrasive cleaners to clean the headphones.
-
Do not use near water devices such as taps, fountains, swimming pools, washing machines etc.
-
Using the headphones while driving can distract you and increase the likelihood of accidents.
-
Battery life may vary depending on the mode of use.
-
Do not allow the headphones to come into contact with sharp objects as this may cause scratches and damage.
-
Please keep out of reach of children.
SBS spa – Via Circonvallazione s/n
28010 Miasino (No) – Italy
Documents / Resources
| sbs
TESPEARMOOVEBTK Wireless
Earphones
[pdf] User Manual
TESPEARMOOVEBTK Wireless Earphones, TESPEARMOOVEBTK, TESPEARMOOVEBTK
Earphones, Wireless Earphones, Earphones
---|---