SECUTEK TECHNOLOGY E7S TWS Wireless Headphones Instruction Manual
- May 15, 2024
- SECUTEK TECHNOLOGY
Table of Contents
SECUTEK TECHNOLOGY E7S TWS Wireless Headphones
Product Information
Specifications:
- Product Model: E7S
- Version: 5.3
- Running Time: about 5 hours
- Talk Time: about 5 hours
- Headphone Capacity: 50mAh/3.7V
- Charging Time: about 1 hour
- Effective Distance: 10m
- Horn: Copper ring 8mm
Product Usage Instructions
Wearing Instructions:
- Open the cover of the charging bin.
- Take out the earphone of the right ear.
- Gently put the earphone into the ear canal of the right ear.
- Repeat the same for the left earpiece.
Operation Mode:
To Start:
- Take out the earphone from the charging bin to start up automatically.
- Press the button for 3 seconds if not starting automatically.
To Turn Off:
- Put the earphone back in the charging bin to shut down and charge automatically.
- Press the button for 5 seconds to power off manually if needed.
Pairing Instructions:
- Open the cover of the charging bin to start pairing mode.
- Search for “E7S” in your device’s Bluetooth list.
- Tap on “E7S” to connect.
- Follow on-screen instructions; reseat earphones in bin if connection fails.
Product diagram
Headset Configuration
- Product Model: E7S
- Running time: about 5 hours
- Headphone capacity: 50mAh/ 3.7V
- Effective distance :≥10 m
- Version 5. 3
- Talk time: about 5 hours
- Charging time: about 1 hour
- Horn: copper ring 8mm.
Packing list
- Charging box *1
- Left and right earphones *1
- Large ear cap *2
- Product Manual *1
- Charging cable *1
Charging bin configuration parameters
Battery capacity: 200mAh/ 3.7V
Charging time: about 1 hour
Input voltage: 5V/200mAh
Wearing a way
Open the cover of the charging bin, take out the earphone of the right ear,
and put the earphone horn end Gently put into the ear canal of the right ear,
and then gently swing the earphone not to shake.Wear the left earpiece in the
same way.
Mode of operation
- The boot
- Open the cover of the charging bin, take out the earphone and start up automatically, and the earphone turns red Blue lights flashing
- When the earphone is off, press the button for 3 seconds to start the headset
- To turn it off
- Put the earphone back to the charging bin, and the earphone will automatically shut down and charge
- When the headset is on, press the button for 5 seconds to power off the headset.
Pairs of ears connected
-
Open the cover of the charging bin, take out the earphone and start it automatically. The red and blue lights are flashing, and we’re in automatic formation mode, one of them If the headphone indicator is off, the team is successfully formed.
-
Open the bluetooth list of the device and search for “E7S”
-
Tap E7S to connect. If the stay connection fails,Put the earphones back in the charging bin and close the lid, then repeat the top The operation procedure is ok.
-
When both ears leave the normal connection distance with the device,Headset The headset is connected back to the Bluetooth headset, and the connection is not completed within 5 minutes If the connection is successful, both ears
will shut down automatically. -
After the headset is turned on and before the phone is disconnected, double-click Automatically switch between Chinese and English on either side of ears.
(Only Chinese or only English products do not have this function)
After the device is first connected,
The next time the headset is restarted,
It will automatically connect the last pair device
Two-ear touch operation
- Play/pause the music
- When the headset is playing, tap L/R once
- Let’s play the last one
- In the music state, tap headset R 2
- Let’s play the next one
- In the music state, tap L headset 2
- In the music state, tap 3 times L volume +
- In the music state, tap three times R The
- volume decreases –
- Answer the phone
- When an incoming call comes in, tap
- the L/R headset once
- Refuse to answer the phone
- When an incoming call comes in, tap
- L/ R headset 2 times (or long press)
- Voice assistant
- When connected, hold down any
- earphone for 1.5 seconds to release
- The voice laktin state is displayed
- Earphone charging: The earphone is automatically charged in the charging case The charging indicator light is red and the red light goes out when it is full Charging case low power: digital tube single digit flashing Charging case charging: digital tube single digit flashing, full 100 stop
F&Q
Q: How do I charge the earphones?
A: The earphones are automatically charged in the charging case. The charging indicator light will be red during charging and turn off when fully charged.
Q: How do I know if the charging case is low on power?
A: The digital tube on the charging case will display a single-digit flashing when the case is low on power.
Q: Howx:-49.66m one earphone has sound?
Y: 118.26 mm A: Put the unpuones back into the charging bin at the same time, close the cover to charge, and then take them out to see whether the dual-ear mode is restored If the fault is not rectified, restore the fault to factory Settings
Q: The phone can' t connect to the headset?
A: Delete the paired TG01 on the mobile phone, and then make the paired connection.
Q: How can I listen to music/talk without sound?
A: phones have a setting icon on the right side of the phone onnection record. Click enter to select two audi oDeselect and then re- select. Enter audio Call mode in Setting General Accessibility, and select Automatic, if it is automatic, then other options, and then change to automatic, if not restored, Delete the pairing record retry attempt.
Q: Why is there a stutter/ stutter?
A: If you use headphones, there are a lot of Wi-Fi devices, 4G signals, high power appliances and so onInterference, stuttering and di scont inuous condi tions may occur, and the connection can be restored by changing the environment or re pairing
Matters needing attention
- Please use a charger with safety certification from a formal source for charging
- Adjust the volume of headphones to avoid damage to hearing 3，the correct use of the product to avoid falling from high or heavy extrusion
- Children should be accompanied by adults to avoid accidental ingestion
- Stay away from extreme environments such as high temperature or humidity
- Do not di sassemble the product
FCC
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuan t to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection againstharmful interference in a
residential installation. This equipment generates, uses and can radiateradio
frequency energy and, if not installed and used in accordance with the
instructions, maycause harmful interference to radio communications. However,
there is no guarantee thatinterference will not occur in a particular
installation. If this equipment does cause harmfulinterferenc e to radio or
television reception, which can be determined by turning the equipmentoff and
on, the user is encouraged to try to correct the interference by one or more
of thefollowing measures:
- Reorient or reloca te the receiving antenna.
- Increase the separation between the equi pment and receiver.
- Connect the equipment into an outlet on a circuit different f rom that to which the receiver is c onnected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must
accept any interference r eceived, including interference that may cause
undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 0cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>