PETCUBE Cam Pet Monitoring Camera User Guide
- June 3, 2024
- Petcube
Table of Contents
PETCUBE Cam Pet Monitoring Camera
SETUP
- Download the Petcube App and register your account
- Power up the camera and wait for yellow light to flash
- Press the Setup button at the bottom until you hear a sound
- Follow the instructions in the app to finish the setup.
PLACEMENT
It’s best to point Petcube Cam in the direction where your pets spend most of
their time so their activities are captured with the wide-angle lens. If
placing on a table or a shelf, put Petcube Cam at least 3 feet above the
floor. A rubber foot at the bottom provides a firm grip on the
surface.
Table or shelf top
Petcube Cam has a non-slip rubber bottom, which provides a secure grip on flat
surface. Camera tilt can be adjusted manually for a better viewing angle.
Hooks at the foot allow to fold the cord firmly.
Mounting
The device can be placed on a wall or a shelf bottom. Petcube Cam comes with a
mounting tape. Use it to place the Cam in the desired location.
LIGHT STATUS
SAFETY INSTRUCTIONS
For more information about safety and handling, please see https://petcube.com/support/cam/user-guide/ To avoid injury or harm, read all safety information and operating instructions prior to using Petcube Cam.
- Don’t drop, hit, or shake your Petcube Cam.
- Don’t stain, scratch, or otherwise damage the front camera glass.
- Don’t expose to liquid, moisture, dust, excessive heat, or open flames.
- To avoid overheating, don’t leave Petcube Cam in direct sunlight.
- Petcube Cam should not be used by minors without supervision from an adult.
- Protect the power cord from being walked on, pinched, or chewed on by pets.
- The socket-outlet shall be installed near the equipment and shall be easily accessible.
- Maximum ambient temperature around the adapter must not exceed 40°C.
- The adapter is used for office machines and data processing appliances. It is certified according to the relevant safety standards UL 62368-1, CSA 022.2 No. 62368-1.
- The output power taken from the supply must not exceed the rating given on the adapter.
- The adapter is not intended to be repaired by service personnel in case of failure or component defect (unit can be thrown away).
- The disconnection from line voltage is made by main plug.
The frequency bands in which the radio equipment can operate – 2400.0 – 2483.5
MHz.
The maximum radio-frequency power transmitted in the frequency bands in which
the radio equipment operates -32.14 (15.07) MW (dbm).
CONTACT
For any assistance with the device, please contact us directly at:
support@petcube.com
We’ll resolve any issue ASAP. Pet parents’ experience is our top priority.
PRODUCT INFO
Petcube user guide
The explanations provided in this guide are for informational purposes only
and may be modified. The latest version of this guide can be found at
https://petcube.com/support/cam/user-guide/
Software
Your Petcube Cam connects to Petcube, Inc. copyrighted software to control its
operation.
Warranty
When Petcube Cam is purchased new through Petcube authorized resellers, it is
warranted against defects in materials and workmanship under normal use. Full
terms can be found at https://petcube.com/docs/warranty/
https://petcube.com/care/
Terms of use
For more information please visit https://petcube.com/docs/terms-of-use/
FCC Warning
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20 cm between the radiator & your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter. Only use the power supply provided.
ISEDC RSS Warning. Canadian Compliance Statement
This device complies with ISEDC license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
ISEDC Radiation Exposure Statement
This equipment complies with ISEDC RF radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter. This equipment
should be installed and operated with minimum distance 20 cm between the
radiator & your body. Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
Declaratlon of Conformity
Hereby, Petcube Inc. declares that this Petcube Cam is in compliance with
Directive 2014/53/EU and Radio Equipment Regulation 2017. The full text of the
declaration of conformity is available at the following internet address:
https://petcube.com/docs/declaration-of-conformity-petcub
Documents / Resources
|
PETCUBE Cam Pet Monitoring
Camera
[pdf] User Guide
CC10USD, 2AK4CCC10USD, Cam Pet Monitoring Camera, Pet Cam, Pet Monitoring
Camera, Pet Camera
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>