Homedics HSD-100 Hand Sanitizer Instruction Manual and Warranty Information

Hand Sanitizer

Instruction Manual and Warranty Information

HSD-100

Congratulations!

Thank you for purchasing the HoMedics Hand Sanitizer. The Hands Sanitizer is one of the most advanced products of its kind. Luxury meets practicality and hygiene meets style:

• Motion sensor technology provides sanitary hands-free operation.
• Adjustable controller dispenses the right amount of soap or gel every time.
• Convenient magnetically attached drip tray removes easily for cleaning.
• Elegant functional design makes hand washing a pleasure.

IMPORTANT:

To avoid accidental dispensing of liquid, slide the Dispensing Control Switch to [OFF] and install batteries before filling the Soap/Sanitizer Reservoir.

How To Install Batteries:

Press the [OPEN] release button on the underside of the unit to open the Battery/Control Compartment door. Insert three (3) AA alkaline batteries carefully following the polarity (+ / -) markings shown inside the battery compartment. Note: when the batteries are low and need replacing, the red LED Low Battery Indicator will flash for 10 seconds after each dispensing cycle.

Caution: All servicing of this product must be performed by authorized HoMedics Service Personnel only.

How To Use

1. Lift the cover to the Soap/Sanitizer Reservoir and fill up to the “Full Line” inside the tank. Do not overfill as this may cause dripping. Replace the plug in the soap/sanitizer tank securely.
2. Press the [OPEN] release button to open the Battery & Control Compartment on the bottom of the unit and slide the Dispenser Control Switch from [OFF] to your desired amount of soap to be dispensed [1 = LOW], [2 = MEDIUM] or [3 = HI]. The Red LED will turn on for 12 seconds. During this period, the Motion Sensor and motor will not function. This will allow enough time to close the Battery & Control Compartment door and position the unit without triggering the Motion Sensor.
3. Attach the Drip Tray.
4. Place your hand under the spout to activate the Motion Sensor. The Hand Sanitizer will then dispense liquid.

How to use the CLEAN Function: If you wish to change the type of liquid in Hand Sanitizer, you may use the CLEAN function to empty and clean the unit. Press the [CLEAN] button and the unit will enter the auto cleaning mode: 1.) first the Red LED will illuminate for 12 seconds to allow you to replace the battery door and position the unit for cleaning, 2.) then the motor will turn on and pump for 30 seconds. During this period, you can press the [CLEAN] button again to abort the cleaning function (motor will turn off). The CLEAN function will work with the Dispenser Control Switch set to [1], [2] or [3]; it will not work with the Dispenser Switch in the OFF position. Repeat until there is no more liquid in the reservoir. To thoroughly flush out the unit, you should add water to the reservoir and repeat the cleaning process.

IMPORTANT:

1. The Motion Detector that activates dispensing uses a sensitive infrared sensor. To avoid accidental dispensing of liquid/saop, please do not place Hand Sanitizer Dispenser in direct sunlight.
2. After a period of inactivity, the lotion inside Hand Sanitizer Dispenser may become dry and clog the Hand Sanitizer. Should this occur, simply use a toothpick or water to remove the obstruction.
3. The only part of the Hand Sanitizer designed to be wet is the liquid reservoir and spout. Do not immerse the Hand Sanitizer in water as the product will be damaged.
4. Remove batteries from the battery compartment and run the CLEAN Function to flush the liquid/soap reservoir with water whenever the Hand Sanitizer is to be left unused for a long period of time.
5. To clean the unit, use a soft damp cloth. Do not clean with a abrasive materials or corrosive substances.

Trouble Shooting:

No Soap/sanitizer Dispensed; Motor Does Not Run

1. Ensure that Dispensing Control Switch is turned ON in the 1 = LOW; 2 = MEDIUM or 3 = HI position; not OFF.
2. Hands are placed directly between the Motion Sensor and Spout.
3. Unit is not placed in bright sunlight which will interfere with Motion Sensor operation.
4. Batteries are installed with correct polarity (+/ -) and not dead.

No Soap/Sanitizer Dispensed; Motor Runs

1. During start-up you may need to activate the Motion Sensor several times to “prime” the pump to begin dispensing soap/sanitizer.
2. The soap/sanitizer reservoir should be at least ¼ FULL.
3. Make sure that no dried soap/sanitizer is clogging the spout or pump tubing. Use a toothpick to clean the spout. If necessary, empty the soap/sanitizer tank, fill with water and run the CLEAN Function.

Battery Precautions:

1. Use AA alkaline batteries only. Do not use rechargeable batteries.
2. Replace all batteries at the same time.
3. Clean the battery contacts and the contacts of the device prior to battery installation with a dry cloth.
4. Ensure the batteries are installed correctly with regard to polarity (+ / -).
5. Remove batteries from the unit when it is not to be used for an extended period of time.
6. Remove depleted batteries from the unit promptly. Dispose of used batteries safely. Keep all batteries away from children. Batteries are small objects and could be ingested. If swallowed, contact a physician at once. Do not open batteries or dispose of in fire. Do not mix the new and used batteries.

Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Homedics HSD-100 Hand Sanitizer Instruction Manual and Warranty Information – Download [optimized]
Homedics HSD-100 Hand Sanitizer Instruction Manual and Warranty Information – Download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>