Homedics SS-6510 SoundSpa Fusion Alarm Clock Radio Sound Machine and Dock for iPod Instruction Manual and Warranty Information

: June 8, 2024
: Homedics

Homedics SS-6510 SoundSpa Fusion Alarm Clock Radio Sound Machine and Dock for iPod Instruction Manual and Warranty Information

Create your perfect sleep environment.

Thank you for purchasing SoundSpa Fusion, the HoMedics ultimate dock for iPod and relaxation machine. This, like the entire HoMedics product line, is built with
high-quality craftsmanship to provide you years of dependable service. We hope you will find it to be the finest product of its kind.

SoundSpa Fusion helps create your perfect sleep environment. Fall asleep to any of the six calming sounds, then wake to iPod, sounds, radio, or beep tone. SoundSpa Fusion can also mask distractions to improve your concentration while you read, work or study.

IMPORTANT SAFETY INSTRUCTIONS:
When using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING

DANGER – To reduce the risk of electric shock:

Always unplug the appliance from the electrical outlet immediately after using and before cleaning.
Do not reach for an appliance that has fallen into water. Unplug it immediately.
Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
WARNING – To reduce the risk of burns, fire, electric shock or injury to persons:
Close supervision is necessary when this appliance is used by or near children, invalids or disabled persons.
Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by HoMedics; specifically any attachments
not provided with the unit.
Never operate this appliance if it has a damaged cord, plug, cable or housing. If it is not working properly, if it has been dropped or damaged, return it to Homedics Service Center for examination and repair.
Keep cord away from heated surfaces.
Never drop or insert any object into any opening.
Do not operate where aerosol (spray) products are being used or where oxygenis being administered.
Do not carry this appliance by power cord or use cord as handle.
To disconnect, remove plug from outlet.
This appliance is designed for indoor use only. Do not use outdoors.
Only set on dry surfaces. Do not place on surface wet from water or cleaning solvents.

SAVE THESE INSTRUCTIONS
Caution – Please read all instructions carefully before operating.

Never leave the appliance unattended, especially if children are present.
Never cover the appliance when it is in operation.
This unit should not be used by children without adult supervision.
Always keep the cord away from high temperature and fire.
Do not lift, carry, hang, or pull the product by the power cord.
If the adaptor sustains damage, you must stop using this product immediately and contact the HoMedics Service Center. (See the warranty section for the HoMedics address.)

Figure 1

Set +/- 10 Sounds
Volume 11 Power
Dock for iPod 12 Audio
Dimmer 13 Snooze/Nap
Timer 14 Aux Connection Cable
Time Set 15 DC Adapter
AL Mode 16 iPod Inserts (4)
AL Set 17 AM Antenna
AL1/AL2 18 Interchangable Faceplates (3)

SoundSpa Fusion Features

6 Nature Sounds: Night, Ocean, Brook, Sunrise, Rain and Water Fall
Charging docking station for iPod
Premium quality speakers
AM/FM radio with digital tuner
Dual Alarm with Snooze
Nap and Auto timer options 15, 30, 45 or 60 minutes
Four wake options – iPod, radio, beep or nature sound
Easy-to-read clock with LCD display

Figure 2 Figure 3

Figure 4
_ **
Figure 5 Figure 6
_**

Before You Begin
The SoundSpa Fusion uses a backup battery system to provide continuous alarm and clock settings in the event of a power failure. Two
“AA” batteries (included) must be inserted into the battery compartment if memory backup is desired. When the Backup Battery is installed, in the event of a power failure or the DC cord is accidentally disconnected, the LCD display will not remain lit, but the current time and alarm time settings will be temporarily maintained.

Changing the Colored Faceplates

Attaching Faceplates

Choose a faceplate.
Slide top lip of faceplate under top lip of SoundSpa Fusion unit (Fig. 5-A).
Press firmly on faceplate until it locks in place (Fig. 5-B).

Removing Faceplates

Use thumb to press latch on bottom of SoundSpa Fusion. Press firmly so faceplate pops off unit (Fig. 6).
See ATTACHING FACEPLATE for directions on replacing the faceplate.

Getting Started

Setting Clock Time

Press the TIME SET BUTTON located on the top of the unit (Fig. 1); hour digit will begin flashing. Turn the SET +/- KNOB until the current hour is displayed. Remember to set the correct AM or PM (an icon in the upper left of the time display is the PM INDICATOR; there is no AM indicator) (Fig. 2).
Press the TIME SET BUTTON again; minute digits will begin flashing. Turn the SET +/- KNOB until the current minute is displayed.
Press the TIME SET BUTTON again to exit the clock setting mode or after 5 seconds the display will stop flashing to indicate the time is set.

Install/Replace Backup Battery

Make sure the DC adaptor is connected. Otherwise the time setting may be lost during battery replacement.
Open the battery compartment cover located on the bottom of the unit.
Insert two AA batteries, checking that the positive polarity matches the picture in the battery housing.
Close the compartment cover.

Battery Precautions

Use only the size and type of batteries specified.
When installing batteries, observe proper +/ – polarities. Incorrect installation of battery may cause damage to unit.
Do not mix different types of batteries together (e.g. alkaline with carbon-zinc or old batteries with new ones).
If the unit is not going to be used for a long period of time, remove batteries to prevent damage due to possible battery leakage.
Do not dispose of batteries in fire. Batteries may explode or leak.

Charging your iPod

The SoundSpa Fusion comes with four dock inserts. See chart below to determine the size insert you should use.

Insert Label

|

iPod Model

---|---
3G nano| iPod nano 3rd Generation
4G nano| iPod nano 4th Generation
Classic 80G/Touch| iPod Classic (80GB & 120GB), iPod Touch (8GB, 16 GB &
2ND Gen.), 5G iPod with Video (30GB), U2 iPod with video
Classic 160G| iPod Classic (160 GB), 5G iPod with video (60GB, 80GB)

When you want to connect a different size iPod, remove the insert from the
SoundSpa Fusion and replace with the correct size insert. To remove dock
insert, place fingernail in slot on insert (Fig 3) and gently pull up. You must
always use the appropriate size insert for your iPod. You may contact
HoMedics Consumer Relations at 1-800-466-3342 to order the correct insert
for your iPod.
Note: Make sure you are using the correct insert for your iPod and that it is
properly docked in the SoundSpa Fusion. Failure to do so may damage
your iPod.

WARNING: INSERT AND PIN CONNECTOR ARE DESIGNED FOR APPLE iPOD MUSIC PLAYERS ONLY. ATTEMPTING TO ATTACH OR
FORCE ANY NON- iPOD MUSIC PLAYER INTO THE ENCLOSED INSERT OR ONTO THE PIN CONNECTOR WILL DAMAGE AND EVEN

DESTROY YOUR DEVICE.

Before you begin, remove your iPod from its case or ‘skin’. Place insert in dock, being sure that the two plastic tabs face the front of the unit.
Press insert into place, ensuring it is firmly placed in the dock. Carefully place your iPod into the docking area so that the pin connector in the dock is fully connected to the pin socket on the bottom of your iPod (Fig. 7).

Figure 7
Your iPod will then begin charging, until fully charged.
NOTE: Your iPod will charge even if the POWER button is turned off. The
SoundSpa Fusion only needs to be plugged in for the iPod to charge.
To remove/replace an insert, first remove your iPod, then place fingernail in slot on insert (Fig. 2) and gently pull up.

Listening to Your iPod

Press the POWER BUTTON on the SoundSpa Fusion (Fig. 1).
Toggle through the AUDIO BUTTON to play the iPod (Fig. 1).
The IPOD ICON will appear on the LCD display on the right side of the clock, to indicate that the iPod mode has been selected.
Note: When the iPod is docked and in standby mode, it will automatically begin playing once the iPod mode is selected on the unit.
Press the PLAY/PAUSE button on your iPod to pause play; press play again to resume play.
Turn the VOLUME KNOB (Fig. 1) on the unit to adjust the system volume.
Press the or on your iPod to go to the next or previous track.
To turn unit off, press the POWER BUTTON. The iPod will continue charging in the dock.

Listening to a non-docking iPod or other portable audio devices

If you are using an iPod without a docking port, other MP3 player, or other portable audio device, you can play it through the SoundSpa Fusion
via the LINE IN located on the back of theunit (Fig. 9).

Figure 9

Plug one end of the Connection Cable (included) into the headphone or line-out jack on your audio device and the other end of the Connection Cable into
the SoundSpa Fusion LINE IN, located on the back of the unit.
Press the POWER BUTTON on the unit to turn it on (Fig. 1).
Toggle through the AUDIO BUTTON on the unit until you reach the auxiliary mode. The AUX ICON (Fig 2) will appear in the right side of
the clock, to indicate that the auxiliary mode has been selected.
Turn on and play external audio device.
Turn on VOLUME KNOB (Fig 1) on the unit to adjust the system volume.
Note: You may need to adjust the volume on external device also.
To turn off the unit, press the POWER BUTTON on the top of the unit.
Note: You may need to turn off your external audio device as well.

Listening to Nature Sounds

Press the POWER BUTTON on the unit to turn it on (Fig. 1).
Select the Sounds button to toggle through the different nature sounds (Fig 1). They will be shown on the bottom of the LCD display, below the time. (FIg. 2)
Turn the VOLUME KNOB on the unit to adjust the volume (Fig. 1).
To turn off the nature sounds, press the POWER BUTTON to turn the unit off, or switch the audio mode by pressing the AUDIO BUTTON (Fig. 1).
Note: When the unit is turned on, it will always default to the last mode used.

Listening to the Radio

FM Antenna
Extend FM wire antenna fully for best FM reception (do not strip, alter or
attach to other antennas).
AM Antenna Snap the AM loop antenna into the base provided. Next, plug the AM loop antenna into the connecter located on the back of
the unit for best AM reception (Fig. 10).

Figure 10

Press the POWER BUTTON on the unit to turn it on (Fig. 1).
Toggle through the AUDIO BUTTON to play the radio (Fig. 1). The RADIO ICON will appear on the right side of the clock (Fig. 2).
To choose between FM or AM radio, press the AUDIO BUTTON again. The FM or AM icon will show on the left side of the clock to indicate the
band that is selected (Fig. 2).
Turn the SET +/- knob on the unit to tune in the desired station (Fig. 1).
Turn the VOLUME KNOB on the unit to adjust the system volume (Fig. 1).
To turn off the unit, press the POWER BUTTON.

Using Auto-Timer

While listening to your iPod, the nature sounds, or the radio, you may set a timer so the unit will turn off automatically after so many minutes.

Toggle through the TIMER BUTTON until the time of your choice, 15, 30, 45, or 60 minutes, is shown on the LCD.
To cancel the timer, toggle through the TIMER BUTTON until OFF is shown on the LCD.

Setting And Using The Alarms

Setting Alarm1 or Alarm2 (Individually)

Press the AL1/AL2 button (Fig. 1). The AL1 or AL2 ICON will appear in the upper right corner of the LCD display to indicate which alarm is activated.
Press the AL SET BUTTON twice (Fig. 1); hour digits will begin flashing. Turn the SET +/- KNOB until the desired hour is displayed. Remember to set the correct time of day, AM or PM (an icon to the left of the time display is the PM INDICATOR; there is no AM indicator) (Fig. 2).
Press the AL SET BUTTON again; minute digits will begin flashing. Turn the SET +/- KNOB until the desired minute is displayed.
Press the AL SET BUTTON again to exit the alarm setting mode or after
seconds the display will stop flashing to indicate the alarm is set.
Note: You can press the AL SET BUTTON at any time to review the alarm setting.
Toggle through the AL MODE BUTTON until the corresponding icon lights on the LCD screen for the wake mode of your choice: iPod, sound, radio, or beep (Fig. 2).
Note: To wake to iPod, your iPod must be properly docked in the unit, or alarm will default to beep wake mode.
Note: When using the sound mode, the unit will set to the last sound you listened to. If you wish to change it, first, press the POWER button to turn the unit on, then press the SOUND button and toggle through until the sound of your choice is shown on the LCD display, then press the POWER button to turn the unit off.
When the alarm is sounding, press the POWER BUTTON on the unit to urn the alarm OFF. The alarm will come on again at the same time on the next day. To stop the alarm from coming on the next day, press the AL1/AL2 BUTTON until the AL1 or AL2 icon disappears on the LCD display. If the icon disappears, this indicates the alarm is disarmed.
Note: If the alarm sounds for 30 minutes continuously it will automatically turn off and reset for the next day

Setting Alarm1 and Alarm2 (Together)

Press the AL1/AL2 button (Fig. 1) until both AL1 and AL2 icons appear in the upper right hand corner of the LCD display to indicate that both alarms are activated
(Fig. 2).
Note: You cannot change the alarm time when BOTH alarms are selected. If you need to change the alarm time for either alarm, follow step 1 under Setting Alarm 1 or Alarm 2 (Individually).
Toggle through the AL MODE BUTTON until the corresponding icon lights on the LCD screen for the wake mode of your choice: iPod, sound, radio,
or beep (Fig. 2). Both AL1 & AL2 must wake to the same mode. Note: To wake to iPod, your iPod must be properly docked in the unit, or it will default to beep wake mode.
Note: When using the sound mode, the unit will set to the last sound listened to. If you wish to change it, first press the POWER button to turn the unit on, then press the SOUND button and toggle through until the sound of your choice is shown on the LCD display, then press the POWER button to turn the unit off.
When the alarm is sounding, press the POWER BUTTON (Fig. 1) on the unit to turn the alarm OFF. The alarm will come on again at the same
time on the next day.
Note: If the alarm sounds for 30 minutes continuously it will automatically turn off and reset for the next day.
To stop the alarm from coming on the next day, press the AL1/AL2 button until the AL1 or AL2 icon disappears on the LCD display. If the
icon disappears, this indicates the alarm is disarmed.
Note: If one of the alarm users still needs their alarm set, you will need to toggle through the AL1/AL2 button until the alarm that corresponds to their wake time is shown on the LCD display.

Snooze Operation

Press the SNOOZE/NAP BUTTON (Fig. 1) on the unit while the alarm is sounding. The alarm will go off for 9 minutes and then sound again. You
may use this feature until you turn the alarm OFF.
Note: After you have pressed the SNOOZE/NAP button once, you may turn off the snooze function prior to the alarm activating again by pressing the POWER button twice. The alarm will come on again the next day at the same time.

Nap Operation
The NAP TIMER FUNCTION will wake you after a nap of 15, 30, 45, or 60
minutes without the need to change your regular Alarm 1 or Alarm 2 settings.

If the system is playing audio, press the POWER BUTTON to OFF.
Toggle through the SNOOZE/NAP BUTTON until the corresponding time of your choice, 15, 30, 45, or 60 minutes, shows on the LCD display.
Toggle through the AL MODE BUTTON until the corresponding icon lights on the LCD display for the wake mode of your choice: iPod, nature sound, radio, or beep (Fig. 2).
Note: To wake to iPod, your iPod must be properly docked in the unit, or unit will default to beep wake mode.
Note: When using the sound mode, the unit will wake to the last sound listened to. If you wish to change it, first press the POWER button to turn the unit on, the press the SOUND button and toggle through until the sound of your choice is shown on the LCD display, then press the POWER button to turn the unit off.
The alarm will sound to wake you up after the selected amount of minutes have passed.
To cancel the NAP TIMER, press the SNOOZE/NAP BUTTON, until OFF shows on the LCD display, which indicates the NAP function is disarmed.

Dimmer Control

Press the DIMMER BUTTON (Fig. 1) to adjust the backlight intensity of the LCD display.

Maintenance

To Store
You may leave the unit on display, or you can store it in its box in a cool,
dry place.
To Clean
Use only a soft dry cloth to clean the enclosure of the unit. NEVER use liquids or abrasive cleaner to clean. Modifications not authorized by the manufacturer may void users authority to operate this device.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by urning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such
modifications could void the user authority to operate the equipment

LIMITED ONE YEAR WARRANTY

HoMedics sells its products with the intent that they are free of defects in manufacture and workmanship for a period of one year from the date of original purchase, except as noted below. HoMedics warrants that its products will be free of defects in material and workmanship under normal use and service. This warranty extends only to consumers and does not extend to Retailers. To obtain warranty service on your HoMedics product, mail the product and your dated sales receipt (as proof of purchase), postpaid, to the following address:
HoMedics Consumer Relations
Service Center Dept. 168
3000 Pontiac Trail
Commerce Township, MI 48390
No COD’s will be accepted.
HoMedics does not authorize anyone, including, but not limited to, Retailers, the subsequent consumer purchaser of the product from a Retailer or remote purchasers, to obligate HoMedics in any way beyond the terms set forth herein. This warranty does not cover damage caused by misuse or abuse; accident; the attachment of any unauthorized accessory; alteration to the product; improper installation; unauthorized repairs or modifications; improper use of electrical/power supply; loss of power; dropped product;
malfunction or damage of an operating part from failure to provide manufacturer’s recommended maintenance; transportation damage; theft; neglect; vandalism; or environmental conditions; loss of use during the period the product is at a repair facility or otherwise awaiting parts or repair; or any other conditions whatsoever that are beyond the control of HoMedics. This warranty is effective only if the product is purchased and operated in the country in which the product is purchased. A product that requires modifications or adoption to enable it to operate in any other country than the country for which it was designed, manufactured, approved and/or authorized, or repair of products damaged by these modifications is not covered under this warranty.
THE WARRANTY PROVIDED HEREIN SHALL BE THE SOLE AND EXCLUSIVE WARRANTY. THERE SHALL BE NO OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS OR ANY OTHER OBLIGATION ON THE PART OF THE COMPANY WITH RESPECT TO PRODUCTS COVERED BY THIS WARRANTY. HOMEDICS SHALL HAVE NO LIABILITY FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES. IN NO EVENT SHALL THIS WARRANTY REQUIRE MORE THAN THE REPAIR OR REPLACEMENT OF ANY PART OR PARTS WHICH ARE FOUND TO BE DEFECTIVE WITHIN THE EFFECTIVE PERIOD OF THE WARRANTY. NO REFUNDS WILL BE GIVEN. IF REPLACEMENT PARTS FOR DEFECTIVE MATERIALS ARE NOT AVAILABLE, HOMEDICS RESERVES THE RIGHT TO MAKE PRODUCT SUBSTITUTIONS IN LIEU OF REPAIR OR REPLACEMENT.
This warranty does not extend to the purchase of opened, used, repaired, repackaged and/or resealed products, including but not limited to sale of such products on Internet auction sites and/or sales of such products by surplus or bulk resellers. Any and all warranties or guarantees shall immediately cease and terminate as to any products or parts thereof which are repaired, replaced, altered, or modified, without the prior express and written consent of HoMedics. This warranty provides you with specific legal rights. You may have additional rights which may vary from country to country. Because of individual country regulations, some of the above limitations and exclusions may not apply to you. For more information regarding our product line in the USA, please visit: www.homedics.com