BOOMPODS Rhythm 60 Stereo Wireless Speaker User Manual

BOOMPODS Rhythm 60 Stereo Wireless Speaker

In the Box

Controls

1. Power on/off. Long press (2)
   Short press’s 3 fames: Factory reset

2. Short press: TWS connection, TWS disconnection
   Long press 25: Bluetooth disconnected

3. Rotate: Volume + Volume –

4. Short press: Switch LED mode
   Long pres. 25: Turn off LED light

5. Short tap1 time:
   Short tap 3 fames: Pause/play/Pick up/hang up the call Previous track
   Short tap 2 times: Next frack/phone call private
   Long fap 25:
   Long tap 4s: Reject the call Switch EQ mode

6. Microphone
   

How to Connect

Switch ON: blue LED indicator will flash, Choose “Rhythm 60” from your device menu, Wait until you hear voice prompt “Connected”. You are now connected, Blue LED indicator will now stay on.

AUX

Pull waterproof cover up from the bottom (gently) to access AUX port, AUX will play automatically once AUX cable is inserted.
Note LED Indicator will fum Green.

Power bank

Pull waterproof cover up from the bottom (gently) to access USB port, you can use this as an emergency power to your phone or other USB chargeable devices.

LIGHS

10 Different LED lights, Short press ” “once to change modes, Mode 1 is defaulted when you power on each time. you can press and hold to switch off lights.

EQ

3 Equalizer settings: bass boost, vocal boost and Boom pods Studio are available, to change: Long press indicator area until you hear the setting Vocal prompt, note that Boom pods studio is defaulted when vou Dower on.

Calling

When you have a incoming call: Short tap once to Answer. Short tap Once to hang up. Short fap twice to move call from speaker to phone to keep call private. Tap Hold for 2s to reject call.

Pair 2

lf you have already paired the Speaker to your phone or other device (in range) clear them from those devices. Switch on both speakers. Short press ” “button, on one of the speakers, now wait until you hear “BEEP” prompt from both speakers. Now pair to your phone, follow the instruction on previa US page.

Charging

Gently remove waterproof cover only until USB-C charging port is exposed. (Please make sure after charging this is securely fixed back in place to avoid water and debris, this could void the waranty) Use supplied USB-C Charging Cable. Use an utput source 5V/2A (or above). Charge when you hear “Battery Low” prompt or the LED indicator flash RED Red LED will be on while charging and switch off when fully charged.

Speaker will power off automatically of save battery when nothing is Connected after 10 minutes.

Specifications

Look after me

1. Please read this manual carefully before use and keep it safe.
2. First time Use, please fully charge
3. Use certified adapter that hoes passed national safety certification.
4. Charge at lease once a month to maintain performance.
5. Do not use in extremely hot or cold environments, temperature beyond 5 C-35C. If Used beyond the above range, the product may stop automatically to protect the internal circuit.
6. When charging in high temperature environments, the product may automatically stop charging to protect the battery. At this time, the charging indicator usually flashes quickly to indicate that the charging environmental temperature or the product internal temperature is too high.
7. Storage environment temperature: -5~35C RH<70% (recommended 20Ct5).

Important safety instructions

1. Do not disassemble or repair this speaker personally, otherwise it may cause product damage or personal injury.
2. Do not Use it in dusty, humid, dry, and high-temperature environments.
3. Do not place this product near a heat source, or a place with direct sunlight, lots of dust, or mechanical vibration.
4. Do not exceed the IPX5 waterproof rating parameters.
5. When the product is fully charged, remove from charging.
6. The maximum ambient temperature should not exceed 40°C.
   *This speaker supports mobile phones/ tablets/ PCs etc. Here this User Manual is illustrated base on mobile phones.

FCC STATEMENT

This device complies with Part 15 of the FCC rules. Operation is subject to the following tv conditions: 1) this device may not cause harmful interference, and 2) this device must acceptancy interference received including interference that may caused undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with then limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation. if this. equipment does cause harmful interference to radio or television receipt which can be determinedly turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocated the rekey Vingo antenna. Increase the separation between the equipment and receive. Connect the equipment into an outlet on a circuit different from that to which the receiver is connect. Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement, the device cane used in portable exposure condition without restriction.
www.b0ompods.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>