STAIRVILLE DMX Splitter 6 RDM User Guide
- June 7, 2024
- STAIRVILLE
Table of Contents
STAIRVILLE DMX Splitter 6 RDM User Guide
Quick
Start Guide
This quick start guide contains important information on the safe operation of the product. Read and follow the safety advice and instructions given. Retain the manual for future reference. If you pass the product on to others please include this manual.
Safety instructions
Intended use
This device is used to distribute an RDM / DMX signal through six separate
outputs. Any other use or use under other operating conditions is considered
to be improper and may result in personal injury or property damage. No
liability will be assumed for damages resulting from improper use.
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not
within reach of babies and young children. Choking hazard! Ensure that
children do not detach any small parts from the product. They could
swallow the pieces and choke! Never let children unattended use electrical
devices.
Where to use the product
Never use the product
- in conditions of extreme temperature or humidity
- in extremely dusty or dirty areas
- at locations where the unit can become wet
General handling
- To prevent damage, never use force when handling the product.
- Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use liquid cleaners such as benzene, thinners or flammable cleaning agents.
Features
- 6-way DMX distributor
- The 19″ rackable DMX Splitter 6 RDM is equipped with a DMX input + DMX link out and six further DMX outputs
- Rear: 1 × DMX input + 1 × DMX link out (terminal or PassThru switchable)
- Front: 6 × DMX output
- Galvanic isolation of the connections
- RDM-W capaWble
- XLR IN / OUT: 3-pin / 5-pin
Operating elements and connections
- PWR : The red LED lights up when the device is connected to the mains.
- DMX : The green LED flashes as soon as a DMX signal is present at one of the DMX IN sockets and goes out when the DMX signal is interrupted.
- OUT 1 – OUT 6: DMX outputs 1 to 6 with 3-pin and 5-pin XLR panel sockets. Always use only one connection to control spotlights etc., never both connections at the same time (use either 3-pin or 5-pin socket).
- POWER IN : Power Twist mains connection socket for the power supply of the device. A suitable power cord is included.
- POWER OUT : Power Twist mains output socket for the power supply of other devices. Make sure that the total current consumption of all connected devices does not exceed 12 A, otherwise injuries and irreparable damage to the device can occur.
- F1AL250V : If the fuse has blown, disconnect the device from the power supply and replace the fuse with a new fuse of the same type. If the fuse blows repeatedly, please contact our service.
- Pass Thru / Terminated : If several DMX splitters 6 RDM are connected in series, this switch must be in the ‘Terminated’ position on the last device in the chain. For all other devices in the chain, this switch must be in the ‘Pass Thru’ position. Only then will the input signals be forwarded to the DMX / RDM THRU sockets.
- DMX / RDM IN : DMX input with 3-pin and 5-pin XLR panel plugs for connecting a DMX control unit. Always use only one connection for the control, never both inputs at the same time.
- DMX / RDM THRU : 3-pin and 5-pin XLR panel sockets for forwarding the DMX signal present at the DMX input (DMX / RDM IN). Always use only one connection to forward the DMX signal, never both outputs at the same time.
Technical specifications
- Supported protocol: DMX 512 and RDM
- DMX / RDM connections: 3-pin and 5-pin
- Voltage supply: XLR 230 V ~ 50 Hz
- Power consumption: 10 W
- Fuse: 1.0 A, 250 V, 5 × 20 mm, fast-acting
- Dimensions (W × H × D): 481 mm × 51 mm × 141 mm
- Weight: approx. 2.1 kg
For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version. Do not dispose of your old device with your normal household waste. Dispose of this product through an approved waste disposal firm or through your local waste facility. Comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.
Thomann GmbH · Hans-Thomann-Straße 1 · 96138 Burgebrach ·
www.thomann.de ·
info@thomann.de
DocID: 483813_16.03.2021
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>