bsi Base and Corner Base Unit Installation Guide
- June 7, 2024
- bsi
Table of Contents
- 800, 900 and 1000 Base and Corner Base Unit Assembly
- Components
- Tools Required
- 1 – 2 Assembly Instructions
- 3 – 4
- 5 – 6
- 7 – 11
- 
Components
Important Information – True Handleless Kitchens Installers: See
Note Above TH
FM
665131
Caution: Some pieces of hardware could be hazardous to small children.
Keep all these items out of reach and do not leave children unattended in the assembly area.
Please read these instructions carefully before proceeding. Refer to the Guide
to Receiving and Installing your Kitchen booklet for further information.
Note: Due to variation in wall conditions no screws are supplied for
fixing the units to the wall. If in doubt consult an expert. Assemble the unit
on a clean solid work surface.
In the interest of continuing improvements we reserve the right to amend or
adjust the specifications without prior notice. Errors and omissions excepted.
These units may be fitted with a drawer system. The drawers are supplied
separately. These instructions show the runner positions for the drawer
system.
Follow the instructions supplied with the drawers for drawerbox assembly.
Every effort has been made to ensure that this product leaves the factory in
perfect condition. In the unlikely event that an item is damaged or incorrect,
please contact the customer services department.
Note – Fitting Handles: (1) Decide where you are going to position each handle to maintain symmetry around your kitchen. (2) Measure the handle centres and mark off each door/drawer position. (3) Drill through the door/drawer using a fine drill (<2.5 mm), then drill back from the rear face using a 4.5 mm drill. (4) Attach with the fixings provided with your handle.
Ref. No. Item Quantity
150101 3.5x12mm 14
150202 4x12mm 16
150201 4x15mm 16/20
150199 
4.5x45mm 4
150198 
55mm Carcase Screw 3
154082 
6
154084 
1
154085 7
154004 
8
154027 6
154068 8
154047 
2
152181 
4
152162 4
150308 2
150309 2
152401 
4/5
152418 
4/5
152402 
2
152148 4
151999
12
151500 
2
Tools Required
Drill G-Clamp (pair)
Medium Crosshead Screwdriver Hammer
Large Flathead Screwdriver Tape Measure
Spirit Level Bradawl
1 – 2 Assembly Instructions
TH Modification required at this stage, see True Handleless guide
for further details.
Drawer Runner
1 x ‘L’; 1 x ‘R’
x4
x2
Fit as third screw
1. 2.
154082 6 154004 6
3 – 4
Note: Drill centre holes of B and E for Base Units. For Corner Base
Units consult kitchen plan for door size and drill accordingly.
Scrap wood Scrap wood
3.
154085 6
5 – 6
TH Modification required at this stage, see True Handleless guide
for further details.
Do Not Over Tighten
Start Locked
7 – 11
Scrap wood
8.
150199 4
 
Note: Countersunk screw goes into back panel D.
9.
150101 2 150202 2 154068 2
10.
150202 4 154047 2
Note: Only drill if drawers are being fit. Base Units drill as
indicated. Corner Base Units consult kitchen plan for door size and drill accordingly. Only drill from the lower set of holes
12 – 13 Without Drawers
TH Modification required at this stage, see True Handleless guide
for further details.
12.
154004 2
13.
150198 2
14 – 15 With Drawers
14. 15.
154085 1 154084 1
16 – 17 With Drawers
Do Not Over Tighten
Start Locked
Drawer Runner
1 x ‘L’; 1 x ‘R’
x4
x2
Fit as third screw
18 – 20 With Drawers
18. 19. 20.
154004 2 150198 2 150198 1
21 – 22
21.
152401 4/800 & 900 5/1000 150201 16/800 & 900 20/1000
22.
152418 4/800 & 900 5/1000
23 – 25 Installation Instructions
23.
150202 2 154068 2
TH Modification required at this stage, see True Handleless guide
for further details.
24.
150308 2 150309 2
25.
Appropriate to wall type (Not supplied) 2
26 – 29
26.
151500 2
27.
152402 2 150101 4
28.
154027 6
30 – 31
 Note: Do not over tighten screws or use a power screwdriver.
31.
150101 8
32 – 35
34. 35.
151999 4 152148 4
36 – 37 Fixed Fascia Fitting
36.
150202 2/4 154068 2/4 151999 4/8
37.
150202 2/4
38 Corner Post Fitting
 Note: Fittings are packed with the Corner Post.
TH Modification required at this stage, see True Handleless guide
for further details.
38.
150124 12 154081 6
39 – 41 Corner Post Fitting
TH Modification required at this stage, see True Handleless guide
for further details.
Note: Fit corner post to adjacent unit, then fit optional blanking
panel to corner base unit, finally attached corner post to corner base unit mullion. Use appropriate number of screws (not supplied). Any excess/hangover does not need to be trimmed as it will be concealed in the void.
40. 39. 41.
Not Supplied 6-10 150124 6
Unit Size
(mm)| Required
Door
Size (mm)| Total Length
in Plan (mm)| Void
“x” (mm)
---|---|---|---
800mm| 300| 925| 125
800mm| 400| 1025| 225
800mm| 500| 1125| 325
1000mm| 400| 1025| 25
1000mm| 500| 1125| 125
1000mm| 600| 1225| 225
Ref. 170801 (05)
Documents / Resources
| bsi
Base and Corner Base
Unit
[pdf] Installation Guide
Base and Corner Base Unit, 800, 900, 1000, FM 66513, 170801 05
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>