R TEC AUTOMATION Interior Sun Sensor User Guide

R-TEC Smart Controls – Interior Sun Sensor RTMISS

Interior sun sensors automatically manage daylight transitions at each window, minimizing reliance on and costs of artificial light.

FEATURES

COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.

TECHNICAL DATA / PACK CONTENTS

PRODUCT SPECIFICATIONS

PACK CONTENTS

1. Sun Sensor
2. Instruction Manual
3. 3V – CR2032 Battery
   

SAFETY

WARNING
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

CAUTION

• Do not expose to moisture or extreme temperatures.
• Do not allow children to play with this device.
• Use or modification outside the scope of this instruction manual will void warranty.
• Installation and programming to be performed by a suitably qualified installer.
• Use only R-TEC Automation® hardware.
• Keep clear when in operation.
• Replace battery with correctly specified type.

IMPORTANT SAFETY INSTRUCTIONS TO BE READ PRIOR TO OPERATION

• It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.
• Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge should not be allowed to use this product.
• Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.
• Keep away from children.

INSTALLATION

SENSOR BATTERY
Pull battery tab out to activate for first use.
REPLACING BATTERY

MOUNTING

1. Ensure surface on glass is clean and free of dust.
2. On the back of the sensor, peel clear plastic off to reveal adhesive.
3. Find desired position on glass for the sensor and press adhesive side to glass.
4. Check that the glazing or the tint on the window will not affect the functionality of the Sun Sensor.
5. Ensure that the light level is enough to activate the Sun Sensor. If it is possible to measure the light intensity using the Lux-meter. The values measured should be according to the level of the sensor mode selected.

FUNCTIONAL OVERVIEW

BUTTONS

MODES

Mode 1 – DEFAULT Close Mode| Mode 2 Open / Close Mode| Mode 3 Shade Detect Mode
---|---|---
Preset light level reached

Light level stays above preset for 2 minutes

Blind goes down

Blind stays down

| Preset light level reached

Light level stays above preset for 2 minutes

Blind goes down

Light level goes below the  preset value for more than 15 minutes

Blind goes back up

| Preset light level reached

Light level stays above preset for 2 minutes

Blind goes down until sensor is covered

Blind goes up until sensor is uncovered

Light level goes below the preset value for more than 15 minutes

Blind goes back up

VIEW AND CHANGE SENSOR MODE

To view the current mode:
Press the SUN button for one second

1. blink indicates mode 1
2. blinks indicate mode 2
3. blinks indicate mode 3
   

To change the mode:
Hold the SUN button until the LED blinks 5 times. The mode has now shifted up by one. E.g. Mode 2 has changed to Mode 3.

LIGHT LEVELS OF LIGHT INTENSITY VALUES

TO CHANGE LIGHT LEVEL SETTING:
Press the SUN key repeatedly until the desired light level flashes.

LIGHT INTENSITY DETECTION
Press the SUN and P2 buttons for one second. → Hold the sensor toward the light.

Response
The unit will indicate light level

LOW BATTERY NOTIFICATION
When the battery needs changing, the currently selected light level LED will blink every 2 minutes.
UP BUTTON
The UP button can be used to manually override the sensor and tell the shade to go up.

PROGRAMMING

PROTOCOL SELECTION
R-TEC Automation® motors use the default ARC protocol mode. If your device is in the “EL” mode, to toggle back to the ARC mode follow the steps below.

Hold P2 while inserting battery

To check which mode the sensor is currently in, press the UP or P2 button briefly.
ARC Protocol: The current LED will blink fast 8 times to indicate that the new (ARC) protocol is currently set. *This is the mode needed for your R-TEC Automation® motor to work.
Acmeda “EL” Protocol: The current LED will blink slowly 4 times to indicate that the old protocol is currently set.

ADDING OR REMOVING SENSOR & CREATING GROUP CONTROL

USING MOTOR P1 BUTTON

USING PRE-EXISTING CONTROLLER
A = Existing controller or channel (to keep). B = controller or channel to add or remove. Press P2 on new sensor.

IMPORTANT
Consult your user manual for your controller or sensor.

TROUBLESHOOTING

page 5.
Battery is inserted incorrectly| Check battery polarity. See page 5.
Radio interference / Shielding| Ensure sensor is positioned away from metal objects and that aerial on motor or receiver is kept straight and away from metal.
Sensor distance is too far from remote| Move sensor to a closer position.
Power failure| Check power supply to motor is connected and active.
Incorrect wiring| Check wiring is connected correctly (refer to motor installation instructions).

Any Questions?
Contact our R-TEC Automation® in-house experts at 866.985.3423. Email us at RTECAutomation@RowleyCompany.com.
© 2021 Rowley® Company. All rights reserved. R-TEC Automation® is a registered trademark of the Rowley® Company, LLC.

Do no dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>