IMILAB EC3 Outdoor Security Camera User Manual
- June 7, 2024
- IMILAB
Table of Contents
IMILAB EC3 Outdoor Security Camera
Please read this instruction manual carefully before using the device and retain it for future reference.
Product Introduction
In this instruction manual, images of the device, accessories, and user interface are for illustrative purposes only and should only be used for reference. The actual device may differ from the illustrations due to product updates and upgrades. Please refer to the actual device.
Packing list: IMILAB EC3 Outdoor Security Camera, wall mounting pack, power
adapter, waterproofing tape for power/LAN cable user manual
Installing the Device
Assemble the camera as shown below. Then secure the camera to the metal rod
with a screw.
Note: The warranty does not cover any damage caused by improper installation.
Please follow the instructions.
Mounting the device
Note: Please check that the Wi-Fi signal is strong enough before mounting the
device.
1. Attach the positioning sticker to the desired installation location. Drill
four holes at the positions indicated on the sticker. Drilling diameter of
around 6.0mm; drilling depth of around 30mm.
2. Insert four plastic expansion nuts into the holes.
3. Cover part of 2-in-1 power and LAN cable with the base plate as indicated.
4. Put the base plate on the wall. Ensure that the 2-in-1 power and LAN cable goes straight down. Secure the base plate by inserting the screws into the expansion nuts.
Note:
• In order to prevent accidents and injuries, please secure the device firmly
onto the wall as illustrated. The wall on which the device is mounted must
have a loading capacity of at least 3 times the weight of the device.
• Do not install the device near a heat source, such as an air-conditioner
compressor, air vent of a range hood, or air vent of a gas water heater.
• As the camera can be rotated horizontally, please pay attention to the safe
turning distance during installation. Do not install the device at a location
where its horizontal movement would be impeded.
Top view
The distance between the base plate and the wall should be at least 50mm to allow for a safe turning distance. Any gap of less than 50mm will result in an obstruction to the camera’s movement.
Waterproofing kit
The camera has a power supply port and a LAN port. Waterproofing must be done
on both these ports.
1. Wrap the power supply port with the waterproofing tape as shown below.
2. Wrap the LAN port with waterproofing tape or a waterproofing sleeve.
• The LAN port can be wrapped with waterproofing tape in the same way as the
power supply port.
• For instructions on the use of a waterproofing sleeve, visit the IMiLab
WeChat account.
Wrapping with the waterproofing
tape
Scan the QR code below to follow the IMiLab WeChat account. Public WeChat
account.
http://weixin.qq.com/r/a0MhOXPEkS7urTda9xZ5
Connecting the Device
-
Turn on the camera
Step1: Insert the power supply cable into the camera’s power supply port. Connect the other end of the power supply cable to a power source.
Step 2: When connected to a power supply, the indicator light will show the camera’s status. When the indicator light is yellow, the camera is being turned on; when the indicator light is flashing yellow, it is waiting to be connected. -
Insert a micro SD card
Ensure that the camera is disconnected from the power supply. Use a screwdriver to remove the protective case and expose the micro SD card slot. The contact points of the micro SD card should be facing the same direction as the camera. Insert the micro SD card into the slot.
Note:
When inserting or removing the micro SD card, please disconnect the camera
from the power supply. Please use a micro SD card from a reputable
manufacturer. The recommended read and write speed of the micro SD card is at
least U1/Class 10.
- Restoring factory settings
Press and hold the reset button to restore the factory settings. The content inside the micro SD card will not be deleted.
Specifications
Name: IMILAB EC3 Outdoor Security Camera
Model: CMSXJ25A
Item Dimensions: 11791116mm
Input: 12V 1A
Net Weight: 495g
Resolution: 1920×1080
Lens Angle: 110°
Operating Temperature: -20~ 40
Aperture: F1.6
Video Encoding: H.265
Wireless Connectivity: Wi-Fi IEEE 802.11 b/g/n 2.4GHz
LAN Connection: 1 x 10/100M adaptive network port
Compatible With: Android 4.4 or iOS 9.0 or higher
FCC ID: 2APA9-IPC025B
Manufacturer: Shanghai Imilab Technology Co., Ltd. (a Mi Ecosystem Company)
Address: Room 908, No. 1, Lane 399, Shengxia Rd., China Pilot Free Trade Zone,
Shanghai, China 201210
For further information, please go to
www.imilab.com.
Support: help@imilab.com
For Business: globamarketing@imilab.com
Connecting to Mi Home App
This product works with Mi Home and can be controlled using the Mi Home app.
Scan the QR code to download and install the Mi Home app. If you already have
the Mi Home app installed, you will be directed to the device connection page.
You can also search for “Mi Home” in an app store to download and install the
Mi Home app.
http://home.mi.com/do/index.html?model=chuangmi.camera.ipc020
About Works with Mi Home
A product that works with Mi Home can be controlled using the Mi Home app.
Please note that such products are only verified at the software level. Xiaomi
and Mi Home are not responsible for the production, implementation of
standards, and quality control of these products and their manufacturers.
Note:
The actual operation may differ from the instructions above due to Mi Home app
upgrades and updates. Please follow the instructions shown by the Mi Home app.
Infrared Night Vision
The light sensor can automatically switch the device to night vision mode
through IR-CUT based on changes in the lighting of the environment. The device
features 10 built-in infrared night vision lights that ensure recording stays
clear even in darkness.
Video Playback
Past videos can only be viewed when a compatible micro SD card is inserted in
IMILAB EC3 Outdoor Security Camera. After inserting a micro SD card and
turning on the device, the camera will automatically start recording. In the
control interface for. in the Mi Home app, tap the playback button to enter
the video playback page. You can also view a recording by selecting a time
period.
Sharing a Video
In the control interface for IMILAB EC3 Outdoor Security Camera in the Mi Home
app, you can set the device as a shared device in the settings menu and invite
others to watch the recordings. Users must download the Mi Home app and log in
to their Xiaomi account in order to view the recordings of the shared device.
Home Security
- The Home Security function can be turned on/off in the control interface for IMILAB EC3 Outdoor Security Camera in the Mi Home app.
- The device can detect and record movements within the viewing angle and push the recording to the client. Users can set the surveillance time, alert sensitivity, alert interval, etc.
Precautions
- The working temperature of the device is -20 to 40. Do not use the device when the temperature is too high or too low.
- For better results, avoid placing the camera in front of or next or a glass surface, a white-colored wall, or other reflective surfaces as this may cause the recording to have un-even lighting between the foreground and background or be over-exposed.
- Please ensure that the device is within Wi-Fi signal coverage. Place it at a location with good Wi-Fi signal strength. Try to avoid placing the device near a metallic object, a microwave oven, or other objects that may cause signal interference.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation. Note: This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC 20cm Statement: This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. This equipment should be installed
and operated with a minimum distance of 20cm between the radiator & your body.
This transmit er must not be co-located or operating in conjunction with any
other antenna or transmitter.
WEEE Disposal and Recycling Information
Correct Disposal of this product. This marking indicates that products should
not be disposed of with other household wastes throughout the EU. To prevent
possible harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and collection
systems or contact the retailer where the product was purchased. They can take
this product for environmentally safe recycling.
Adaptor Statements
For pluggable equipment, the socket-outlet (power adaptor) shall be installed
near the equipment and shall be easily accessible.
Hereby, Shanghai Imilab Technology Co., Ltd. declares that the radio equipment type IMILAB EC3 Outdoor Security Camera is in compliance with Directive 2014/53/EU.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>