ACE LED Troffer AT1 Instruction Manual
- June 3, 2024
- ACE
Table of Contents
Troffer AT1 Instruction
Manual
LED Troffer AT1
ACE LED TROFFER (AT1) INSTALLATION INSTRUCTIONS
READ CAREFULLY BEFORE INSTALLING FIXTURE.
PLEASE KEEP THIS MANUAL FOR FUTURE USE.
Fixtures must be wired in accordance with the national electrical code and
all applicable local codes. Proper grounding is required for safety.
This product must be installed in accordance with the application code by a
person familiar with the construction and operation of the product and the
hazards involved. Make certain power off before installing or maintaining
fixture. Check that voltage is compatible with fixture driver, use approved
connectors for all electrical connections
LED troffer not suitable for using in wet locations.
LED troffer not suitable for covering with thermally insulating material.
Please keep the LED troffer away from any corrosive substance, and please use
dry cloth when you clean it.
WARNING
Risk of Fire or Electric Shock
Make sure power supply is off before installing or maintaining the product.
Risk of fire or electric shock. Install this product only in the luminaires
that have the construction features and dimensions shown in the photographs
and/or drawings and where the input rating of the product does not exceed the
input rating of the luminaire. Install the recessed troffer only in 15/16”
NEMA type G or type NFG t-grids with a minimum troffer depth of 3”. Risk of
fire or electric shock. To prevent wiring damage or abrasion, do not expose
wiring to edges of sheet metal or other sharp objects.
Risk of fire or electric shock. Installation guide requires knowledge of
luminaire electrical systems. If not qualified, do not attempt installation.
Contact a qualified electrician.
Risk of fire or electric shock. Only those open holes indicated in the
photographs and/or drawings may be made or altered as a result of kit
installation. Do not make or alter any open holes in an enclosure of wiring or
electrical components during installation.
Risk of fire or electric shock. Never perform maintenance or cleaning while
fixture is energized. Disconnect power and allow fixture to cool before
maintaining.
Risk of injury. Wear safety glasses and gloves during installation and
servicing.
**** MAINTENANCE CAUTION
- Review the diagrams before beginning and make sure the fixture is grounded properly.
- For lighting controls, use driver wiring diagram.
- Turn power off and wait for fixture to cool.
- Maintenance must be done by qualified electricians.
TECHNICAL SPECS
Part No.| Power| Working Current| Input Voltage| Efficacy| CCT| Viewing Angle|
CRI| PF| Dimmable| Warranty
---|---|---|---|---|---|---|---|---|---|---
AT10S-A2-ADJ-22-ADJ-80-FR -LV-GRID- xxx]-10V| 30W / 35W / 40W| 0.367A| AC
120-277V| 125 LPW| 3500K / 4000K / 5000K| 120°| ≥80| ≥0.9| 0-10V| 5 Years
AT10S-A2-ADJ-24-ADJ-80-FR -LV-GRID-[xxx]-10V| 30W / 40W / 50W| 0.458A
Dimensions | 2×2 | 2×4 |
---|---|---|
L | 23.74” | 47.75” |
W | 23.74” | 23.74” |
H | 2.08” | 2.08” |
INSTALLATION GUIDE
|
---|---
Unscrew the driver cover.| Connect the conduit to the driver box.
|
Connect other wires separately.| Put back the driver cover and fix it by
screw.
Recessed Installation
-
Replace existing lighting fixture from ceiling with LED Troffer.
-
Use the protective brackets for safety.
Linmore LED Labs, Inc.
2360 S Orange Ave, Fresno CA 93725
559-485-6010
linmoreled.com
info@linmoreled.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>