Blueair Car Air Purifier User Manual

: June 7, 2024
: Blueair

Blueair Car Air Purifier

product

General

Blueair Cabin P1 car air purifier

The car air purifier is designed for use in small to medium-size cars, purifiying the air while the car is in use. Blueair´s HEPASilent™ advanced filtration technology enables the car air purifier to remove harmful pollutants (i.e. VOCs such as
Formaldehyde), particles and odors. A control knob (also 12V power) enables the driver to either change the fan speeds (3 speed options) or activate the Clean Cycle program.

A 4,5 m cable connects the control knob to the main unit so that it can be installed behind a backseat headrest. The product is equipped with an easily accessible USB charging port so that back seat passengers can charge another device while the cabin air is cleaned. Similarly, a USB charging port on the control knob is available for use by the driver or front seat passenger.

Safety instructions

General

DISCLAIMER:
Ensure that the car air purifier is installed according to the instructions in the user manual. For your safety use only the items supplied in the box. Whilst operating the device, the driver must be aware of, and take into consideration the prevailing traffic conditions. Blueair declines all responsibility for personal harm or injury whilst using the product if the installation has not been carried out correctly or if the product is used incorrectly.

The car air purifier is an electrical appliance. Read these safety instructions carefully before use and take the necessary precautions to reduce the risk of fire, electric shock or injury.
The car air purifier warranty applies only if the product is installed, used and maintained according to these instructions.
Please do not adjust the settings , or look at the display of the car air purifier whilst driving.
Please do not look at your mobile phone whilst driving. You must comply with all applicable safe driving laws and behaviors, including those addressing the use of mobile devices.

WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION : Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.

WARNINGS

To avoid a hazard, a supply cable must always be replaced (because of damage, malfunction or any other reason) by the manufacturer, service agent or similarly qualified person.
Do not spill any liquids such as water, detergents or flammable solvents on the device. Do not use the device if any liquids have spilled on it. If there is a spill, wipe the exterior of the unit with a soft, clean, damp cloth.
Use only the mounting strap included in the box and ensure that the unit is securely fastened as specified. Blueair disclaims all liability for any harm or accident caused by improper installation, usage, disassembly and maintenance by any user or third party.

Note: The mounting strap shall not be removed from the unit.

To avoid injury it is important not to install the unit in front of, or near the safety airbag which is normally located in the dashboard in front of the front passenger seat.
Only use the power cable provided with your car air purifier to plug directly into an appropriate 12V power outlet in a car.
The car air purifier is designed for connecting to a 12V power outlet in a car that is automatically turned on or off when the ignition is turned on or off. Therefore we highly recommend using a ignition-controlled 12V power outlet in the car to avoid the risk of draining the batter Note: The product can also be installed in a boat, truck or RV/motorhome 12V power outlet. Ensure that the unit is securely fastened.
Do not alter the plug in any way.
Do not use the unit if the power cable or plug is damaged or malfunctions in any manner.
Keep the power cable away from heated surfaces.
No foreign objects should enter the unit as this may cause a electric shock or damage.
To prevent damage to the unit do not block the air outlet, air inlet and air ducts.
Install the unit in a position where air can fully circulate around it – do not cover the unit.
The device contains high precision technology. Dropping or striking the device may cause damage.
Install the unit in the appropriate position inside the vehicle by using accompanying accessories and according to the instructions in the user manual.
Do not remove or replace the mounting strap that is delivered with the unit

Intended use

CAUTIONS:

This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
To avoid electric shock or damage, keep the product out of the reach of children since it is not a toy.

COMPLIANCE AND STANDARDS:

This product complies with: SRRC, CMIIT ID no:

Blueair Cabin P1 car air purifier

Open and unpack the box
Read the User Manual and Quick Start Guide Please refer to www.blueair.com for more information

IMPORTANT! Please note that the Particle+Carbon filter is not mounted inside the unit when purchased. The filter is a separate item inside the box and MUST be installed before use

Contents of box

Purifier unit
Mounting strap
Particle+Carbon filter
Control knob with a 4,5m power cable
User information
Top cover
Folded Particle+Carbon filter
Unfolded Particle +Carbon filter
Purifier unit base
Top cover release lock
USB charging port
Main unit base (top view)
Filter reset button
Control knob
USB charging port
Power cable
Back view
Mounting strap
Cable plug area
Power supply port (12 V)

Filters

IMPORTANT! Please note that the Particle+Carbon filter is not mounted inside the unit when purchased. The filter is a separate item inside the box and MUST be installed before use.

One Blueair Particle+Carbon filter is delivered with car air purifier. This filter removes the following airborne pollutants from the car:

IMPORTANT! Use only genuine Blueair filters to ensure proper function of your unit and to qualify for full warranty coverage.

Filter checklist

To make it easy to find the right filter in the future, please fill in the customer record below and keep this user manual for reference. The model number and serial number of this product can be found on the rating label on the bottom of the unit.
Model number
Serial number
Retailer’s name
Retailer’s address
Date of purchase Telephone number

Blueair filter subscription program

This convenient service is available in some countries – contact your local Blueair retailer or check the Blueair website to find out if you can join.

Getting started

Remove the top cover

Place the purifier unit on a flat surface or car seat and release the top cover by pressing the left and right release locks IN and UP as shown.
Lift off the top cover.
Turn top cover upside down and place next to the purifier unit base

Install the filter

Remove the plastic bag from around the filter and pull the two sides of the filter apart to form a square.
Mount the unfolded filter onto the purifier base unit.
Remount the top cover onto the purifier base unit

Note: As a safety precaution the unit cannot start unless the top cover is installed correctly

Note: There is no need to press the filter reset button for initial filter installation.

Attach the mounting strap

1. With purifier unit base face down on a flat surface, thread the mounting strap through the two silver buckles (as shown). Velcro side faces unit.

Connect cable to unit

Before installing the unit into the car, connect the power cable to the power supply port on the back of the unit.

Place and install the unit

Firmly secure the unit behind a back seat headrest by adjusting the mounting strap accordingly

Connect control knob and 12 V power supply

Connect the control knob with power supply into the 12 V power supply port located near the driver. (Refer to page 5 for more information)

Cable management

Run the cable under carpets or other plastic details between the control knob and the unit. To avoid cable damage when adjusting car seats, do not run too close to the seat tracks. Coil any cable excess and fasten with the supplied cable tie.

Functionality

General

The car air purifier unit is controlled by pressing down the control knob to adjust the fan setting

Notes:

In order for the unit to clean the air optimally, please ensure that the car´s recirculation mode is active and any window or sunroof is closed.
When the unit is powered off and then powered-up again, then the fan speed is activated at the same speed as the last used setting.
The cleaning time depends on the cabin volume of the cars in question. Blueair Cabin P1 car air purifier is recommended for use in cars up to mid-size (see table on page 12).

The control knob – overview

The control knob is mounted into the 12V power supply port, e.g. on the dashboard of the car.
The other end of the cable is inserted into the power supply port located on the main unit.
A USB port on the control knob enables the driver or front seat passenger to connect and charge another device (e.g.mobile phone).

Press the control knob once and toggle through the fan speeds (see section “Adjusting fan speed”). The control knob display is only illuminated when the fan is active

Information

The control knob can also display:

Low fan speed
Medium fan speed
High fan speed
Clean Cycle mode
Back to low fan speed etc.
Unit power on/idle mode
Filter change alert
Fan speed setting
Notifications (see section “Notifications”)

Turn on

To turn unit on press once.
Note: The unit must be connected to the power supply port and powered up (i.e. the car´s ignition is on) When the unit is turned on, the start up sequence begins and the fan starts in the last setting.

Adjusting the fan speed

By pressing once, the sequence goes round in a loop from Low speed to Medium Speed to High Speed to Clean Cycle mode to Low speed etc.

Clean Cycle program

The Clean Cycle program starts automatically with a high fan speed in order to purify the cabin from particles and gases as fast as possible. After 6 minutes. the fan speed decreases to medium and runs for 3 minutes, finally decreasing down to low speed as long as the unit is connected to the power supply. Press the control knob to toggle to another fan speed setting (Low, Medium or High) – or press and hold for 3 seconds to turn the unit to idle mode

Idle mode

Press the control knob for and hold for 3 seconds. Any LEDs that are on will fade out during a period of 2 seconds

Notification

3 red LEDs blink in a triangle formation should a notification or error occur (see table below)

Note: As a safety precaution the unit cannot start unless the top cover is installed correctly.

SI T U A T ION| R E COMME NDE D A C T ION
---|---
Top cover open| • Check the filter is installed correctly

• Check that the top cover has been correctly installed

Unit is not working – unit is disconnected from the control plug.| Check that control knob is correctly installed and that the cable/connector is not damaged.
Unit is not working – USB charging port overload If an extra USB charging port is powering too many external units – ie phones etc – the power load might be too much for the system and thus it shuts down.| Remove external units until the unit works.
General hardware failure| Contact customer service
Other error not indicated by error code. The LEDs on the control knob do not light up even though the unit is functioning.| Contact customer service

Changing the filter

A filter change alert is displayed on the control knob when a filter change is due.

Lift off the top cover and mount the new filter onto the purifier base unit
Note: The notification (3 red LEDs) appears as soon as the top cover is removed and remains visible until the top cover is remounted.
Turn on the car´s ignition.
Turn on the unit – (a blue LED lights up on the top cover indicating the unit is powered-up).
Note: The recommendation of approximately 6 months/180 days between filter changes is based on a usage of 360 hrs during that period (2,5hr 6 days 4 weeks * 6 months).
Press the filter reset button.
Remount the top cover onto the main base unit

Care and maintenance

We recommend regular cleaning in order to keep your unit in top condition.
When changing filters

Wipe the underside of the top cover clean after removal.
Vacuum the air outlets using a soft brush and/or other suitable attachment.
Vacuum the small air inlets with a soft brush attachment.

General

Wipe the exterior of the unit with a soft, clean, damp cloth.
Never clean with gasoline, chemical solvents or corrosive material as these agents may damage the surface.
Do not allow foreign objects to enter the ventilation or exhaust openings. This may cause electric shock or damage the unit.
Do not try to repair or adjust any of the electrical or mechanical functions on your Blueair unit yourself. Contact your local dealer or Blueair for warranty information

Environment protection:

Let’s protect the environment! Our products and packaging are sustainably designed and made from recyclable materials. Do not discard the filter or the product with household waste. Bring it to the nearest official waste recycling service.

Help and support If you have questions about Blueair products, please visit www.blueair.com.

Warranty information: The Blueair Limited Warranty applies only if the unit is installed, used, and maintained according to the instructions in this manual. www.blueair.com