Redsbaby JIVE 2 Pram Instruction Manual

Redsbaby JIVE 2 Pram Instruction Manual

General Instructions

This document contains important information and must be kept for future reference. Please read thoroughly before commencing assembly, and
use of your Redsbaby JIVE2. Incorrect assembly, and use can be dangerous and result in serious injury or even death. There may be slight variations in the design of your product to that shown in the images of this instruction manual. Your Redsbaby  JIVE2 chassis is only compatible with the Redsbaby JIVE2 / METRO2 seat unit or Redsbaby JIVE2 / METRO2 bassinet. Do not use your Redsbaby JIVE2 chassis with any other model of pram seat or bassinet. Your Redsbaby JIVE2 chassis can be used with Maxi-Cosi, Britax, Joie and Nuna car capsules (sold separately) using our Redsbaby JIVE / METRO Maxi-Cosi adaptors sold separately or, for a Britax capsule, the adaptors that are used to connect your bassinet to the frame.

TIP! You can also view our Assembly and Daily Use instructional videos on the Redsbaby YouTube channel

Your 24 Month Warranty covers manufacturing defects relating to your pram/accessories as listed below:

• Chassis, frame, wheels and adaptors;
• 5-point harness buckle, padding, strapping and assembly; and
• All soft good seams, bindings and zippers. To the extent permitted by law, the following are not covered by warranty:
• Failure or defects resulting from improper care or use;
• Normal wear and tear including scratches to the pram frame;
• Scuffs and tears to leatherette handles/bumpers;
• Products purchased second hand or from an unauthorised distributor;
• Fading or discolouration of fabrics and materials due to cleaning and/or excessive sun exposure;
• aulty or incorrect assembly of the products by the customer;
• nstallation of a part or accessory not compatible with the product and/or not manufactured by Redsbaby;
• Any modification or alteration not conducted or authorised by Redsbaby;
• Corrosion or rust on the wheels and chassis due to extreme environmental conditions, including high humidity, salt spray, ice or snow or due to insufficient maintenance;
• Accidental or intentional damage, abuse or neglect;
• Damage to handle bar grips or fabrics as a result of normal handling and daily use;
• Airline/transport damage: check your Redsbaby product carefully after it has been handled by the airline (or other
• transporters) and if required, submit your claim directly to your travel insurer/airline;
• Consumer dissatisfaction with the product in terms of disliking the fit, weight, functionality, colour or style (outside of the 30 Day Trial period);
• If the batch number sticker has been damaged or removed; and
• When the product has not been used for normal use and in accordance with the manufacturer’s instructions.

For more information on our 24 Month Warranty, please read our Terms and Conditions at www.redsbaby.com.au. Please ensure you follow the assembly instructions, which can be found in this instruction manual

How to make a warranty claim

To submit a warranty claim please visit the Suppor Centre page on our website, www.redsbaby.com.au and complete the Warranty Claim form. The more detailed
you are with your description of the defect, the quicker we will be able to process your warranty claim. Once your form has been submitted, a member of our Customer
Care team will contact you within seven (7) business days. Depending on the nature of the claim, we will either send out a replacement part to resolve the issue or request a
repair at one of our Australia-wide repair centres. Alternatively you can call our Customer Care team on 1300 344 964.

Warnings and safety precautions

Please read the following warnings and safety precautions thoroughly before using your Redsbaby JIVE2. Incorrect assembly and use can result in serious injury or death.
Always follow safety instructions for assembly, folding and use. Always ensure that your Redsbaby JIVE2 is correctly assembled and locks are engaged before use.
After unpacking, immediately discard any plastic wrapping and packaging materials, as these can lead to a choking hazard.
Always use the safety features that come with your Redsbaby JIVE2, such as the tether strap, brakes and harness.

GENERAL WARNINGS:

• To avoid injury or death: Always apply the brakes whenever the Redsbaby JIVE2 is stationary.
• Do not leave children unattended.
• Secure the child in the harness at all times.
• Do not carry extra children or bags on the Redsbaby JIVE2.
• Make sure children are clear of any moving parts if you adjust the Redsbaby JIVE2, otherwise they may be injured.
• Ensure the frame fold locks are engaged correctly before placing a child in the Redsbaby JIVE2.
• Follow the manufacturer’s instructions.
• Put on all the brakes whenever you park the  Redsbaby JIVE2.
• Use the harness at all times.
• When not in use disconnect shoulder straps from the waist strap and/or buckle.
• The harness can form loops which may cause a strangulation hazard. Never leave a harness connected when not fitted to a child in the Redsbaby JIVE2.
• Use the tether strap to stop the Redsbaby JIVE2 rolling away.
• Do not use the seat or bassinet with any other models of pram/stroller.
• Do not use bassinet once the child can sit up unaided.
• Only use the bassinet in the flat position. Do not recline.
• Do not use any accessories that are not designed for or compatible with the Redsbaby JIVE2.
• Take care when using on stairs or escalators.
• We recommend you do not use the Redsbaby JIVE2 on stairs, as this may damage the frame and lead to breakage.
• Do not use or leave the Redsbaby JIVE2 near open fire or exposed flames.
• Brakes must always be applied when the Redsbaby JIVE2 is not moving.
• The Redsbaby JIVE2 is compatible with the Redsbaby JIVE / METRO Buggyboard. The maximum weight of a child on the board is 20kg (44.1lbs). Ensure you securely connect the JIVE / METRO Buggyboard to the tubing that runs between the rear wheels of your Redsbaby JIVE2.
• The rearward-facing position of the seat is only intended for a child up to 2 years, or until the child’s feet extend over the edge of the leg rest. The front-facing position
  should be used from then on.

GENERAL SAFETY PRECAUTIONS:

• When the vehicle is being folded and unfolded, there is potential for fingers or parts of the body to be injured and due care should be exercised.

• Overloading, incorrect folding or the use of nonapproved accessories may cause injury or damage your Redsbaby JIVE2.

• Ensure you follow the regular maintenance and care instructions included in this manual. Pay special attention to maintenance and care of the brakes.

• The Redsbaby JIVE2 can be used for two (2) children only when using the Redsbaby JIVE2 Second Seat Conversion Kit. Without the Second Seat Conversion Kit, the Redsbaby JIVE2 can only be used for (1) child.

• Do not hang bags on the Redsbaby JIVE2 handles, as this can cause it to become unstable.

• Do not lift or carry the Redsbaby JIVE2 when a child is in it.

• Do not lift or carry the Redsbaby JIVE2 when fully assembled. Only lift and carry when folded.

• The Redsbaby JIVE2 is designed for use on flat or gentle sloping surfaces and may be unstable on higher sloping and uneven surfaces. The vehicle may tip over when used incorrectly on steep inclines/declines.

• Take care when changing terrains and when going over uneven surface levels (inclines/declines/curbs/obstacles)with your pram. Ensure you apply pressure to the handle
  to lift the front wheels over uneven surface levels or when meeting an incline or decline as required (also called ‘popping’ the front wheels). Failure to take care when changing terrains or surface levels, and when going over uneven surface levels, may cause your pram to become unstable.

• Do not leave the rain cover on without the ventilation window on the front of the rain cover open.

• When using your Redsbaby JIVE2 on stairs or escalators, take care.

MAXIMUM WEIGHT LIMITS:

• Maximum weight for a child in the bassinet is 9kg (19.8 lbs).
• Maximum weight for a child in the upper seat is 20kg (44.1 lbs).
• Maximum weight for a child in the lower toddler seat is 17kg (37.5 lbs).
• Maximum weight for items in the basket is 12kg (26.4 lbs).
• Maximum weight for items in the back pocket is 1kg (2.2 lbs).

Features and components

1. Adjustable handle                        8. Circular frame
2. Extension canopy                        9. Adjustable foot rest
3. Frame fold latches                       10. Brake
4. Bumper bar                                 11. Front swivel wheels
5. Frame                                          12. Basket
6. Fold lock                                      13. Rear wheels
7. Seat unit

Assembly instructions

Frame

To release the frame from the folded position:

1. Place frame on the ground and position yourself behind the brake.

2. Release the automatic frame lock located on the left hand side of the frame.
   

3. Holding the frame on both sides, gently lift the frame upwards, continuing until the frame locks into place. When the frame has been fully opened, you will hear
   and feel a firm ‘click’.
   

Brake component

The brake will come permanently assembled on your pram frame and is located at the bottom of the frame in the right hand side and is red in colour.

Rear wheels

Fit the rear wheels by pressing the center button on the wheel, and inserting them into the rear wheel housing located at the back of the pram frame. Once inserted,
release the center button of the wheel to secure in place.

IMPORTANT:

Ensure you check that the wheels are clicked in correctly by tugging them outwards. Failure to attach  the wheels correctly will result in them falling off the pram while in use. To remove, simply press the button in the middle of the wheel to release and pull outwards to remove.

Front swivel wheels

Fit the front wheels by inserting them into the front wheel housing located at the front of the frame. You will hear and feel a firm ‘click’ when the wheels are locked in place.

Assembling the seat and bumper

1. The seat fabrics will come assembled on your Redsbaby JIVE2 circle frame.
2. Attach the bumper by aligning the ends of the bumper with the two openings on the circular frame. Gently push down into place until you hear and feel a firm ‘click’ on both sides.
3. If desired, attach the canopy.
4. To place the seat on the frame, push down gently until you feel and hear a firm ‘click’.
   

**Basket

**

The basket will come assembled on your Redsbaby JIVE2. To remove, release all press studs and clips.

Using your Redsbaby JIVE2

To release the frame from the folded position:

1. Release the frame fold lock on the left hand side of the frame
   

2. Holding the frame on both sides, gently lift the frame upwards, continuing until the frame locks into place. When the frame has been fully opened, you will hear
   and feel a firm ‘click’.
   

To fold the frame

1. Remove the bassinet or seat unit if attached to the frame.
2. Simultaneously pull back on the frame fold latches on the left and right hand side of the frame.
3. Gently fold the frame forwards and downwards until the frame fold lock engages.
   

Tip: You can also fold the Redsbaby JIVE2 with the seat connected in the fully upright and forward-facing position.

Safe lifting and carrying of the Redsbaby JIVE2 frame when folded:

1. Always lift and carry the frame using two hands.
2. Ensure the frame fold lock is engaged.

IMPORTANT:

• Do not lift or carry the Redsbaby JIVE2 when a child is in it.
• Do not lift or carry the Redsbaby JIVE2 when fully assembled.
• Only lift and carry when folded.

Engaging and releasing the brake

The brake is located next to the right rear wheel of the
Redsbaby JIVE2. The brake is identified by its red colour.

1. To engage the brake, press downwards and backwards on the brake until you feel and hear a ‘click’.
2. To release the brake, press your foot forwards on the brake in the opposite direction until the brake lock disengages. You can also flick the brake upwards to disengage if its comfortable for you to do so.
   

IMPORTANT:

• Ensure the pram is completely stationary before applying the brake.
• Ensure you have disengaged the brake completely before pushing your pram. If you hear a clicking sound, double check the brake lock isn’t clicking
  on the rear wheel. It can be helpful to push your toe downwards on the brake in the released position firmly to ensure the brake lock is not touching the rear wheel.

Locking the front swivel wheels

1. Press downwards on the buttons located on top for the front wheel housing until you hear and feel a ‘click’.
2. Push the Redsbaby JIVE2 forwards until you hear a second click in both front wheels.
3.  To unlock, simply press the buttons again. When released successfully, you will hear and feel a ‘click’.

Adjusting the handle

Simultaneously pull the tabs located under either side of the handle and move the handle to the desired height.

Using the 5-Point Safety Harness

1. Clip shoulder and waist straps into center buckle securely.
   IMPORTANT: For the safety of your child the 5-point safety harness must be properly fitted and adjusted.
   
   Note: The shoulder heights can be adjusted according to your child’s height by feeding the shoulder straps through the seat back. The shoulder straps should sit just above the shoulders of your child.

2. Adjust the shoulder strap (A1) and (A2), waist straps (B1) and (B2) and crotch strap (D) to the desired fit.
   

3. To unlock the 5-point safety harness, simply press the button in the middle of the centre buckle (C) to release all straps at once.
   Note: Padding has been provided for the shoulder straps (A1) and (A2) and crotch strap (D) for the comfort of your child.
   

Reversing and reclining the seat

1. To recline, lift the lever located at the top of the seat back and move the seat into the desired position.
   IMPORTANT: Do not reverse the seat when a child is in the seat.
   IMPORTANT: The lever MUST be fully released (pulled upwards) before trying to lower or raise the seat. If the lever is not fully released, the seat will not move.

2. To reverse, remove the seat unit by pushing the tabs located on either side of the seat unit inwards and lift upwards. The seat unit can be fitted either rear or
   forward facing.
   

Using the tether strap

Attach the tether strap to your wrist at all times when using the Redsbaby JIVE2.

Lifting and carrying the Redsbaby JIVE2 safely

IMPORTANT:

• Do not lift or carry the Redsbaby JIVE2 when a child is in it.
• Do not lift or carry the Redsbaby JIVE2 when fully assembled.
• Only lift and carry when folded.

Adjusting the footrest

The footrest can be adjusted into three positions. Simply press the buttons on either side of the footrest to adjust the footrest downwards into the desired position. To adjust
into the upper positions, simply lift the footrest upwards and it will click into position and hold with downward pressure.

IMPORTANT:

The footrest will move freely in the upwards direction and doesn’t lock into place. This is normal and allows the footrest to fold into the frame without resistance
when folding the JIVE2 with the seat attached.

Product care

IMPORTANT:
Ensure you follow the regular maintenance and care instructions. Pay special attention to maintenance and care of the brakes.

General Maintenance

• Regularly inspect the locking devices, brakes, harness assembly, catches, seat adjusters, joints and fixings to ensure they are secure and in full working order.

• Do not store your Redsbaby JIVE2 in your car for prolonged periods of time, especially when it is hot as this may lead to warping some of the plastics parts and reduce the life of your product.

• The brakes and wheels are subject to wear and should be replaced as and when necessary. Brakes are available through contacting our Customer Care team at info@redsbaby.com.au

• Should any parts of the Redsbaby JIVE2 become stiff or difficult to operate, ensure that dirt is not the cause. Use a light application of a silicone spray lubricant, ensuring
  the lubricant penetrates between the components. Use sparingly, as excessive application may encourage the accumulation of dirt. Regular light lubrication of moving parts will extend the life of your Redsbaby JIVE2 and make operating, opening and folding much easier.

• Do not leave the Redsbaby JIVE2 in sunlight for prolonged periods of time, as the colour of some fabrics may fade.

• Store the Redsbaby JIVE2 in a dry, well-ventilated and safe place.

• Do not use your Redsbaby JIVE2 if any screws are loose or missing or if any component is damaged.

Cleaning
Plastic and metal parts

•  Sponge clean with warm water and a mild detergent and then air dry.
• Do not use any abrasive or corrosive cleaning products on your Redsbaby JIVE2.
• Do not use products that contain alcohol, as they may cause stains, discolouring and damage to the leatherette parts on your Redsbaby JIVE2. This includes
  applying hand sanitiser to your hands or directly on the product

Fabrics

• May be cleaned by sponging lightly with warm water and a mild detergent (ensure your child is not allergic to the detergent you use). Then air dry.
• For more instructions, follow the care labels on each fabric item.

IMPORTANT:

Do not place any fabric or other component of your Redsbaby JIVE2 in the dryer. Allow all parts to dry thoroughly before storing.

Read More About This Manual & Download PDF:

References

• Official Redsbaby | Baby Prams, Carriers, Nursery & more.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>