Lumary Smart Wi-Fi Speed Ceiling Fan Switch User Guide

: June 7, 2024
: Lumary

Table of Contents

Lumary Smart Wi-Fi Speed Ceiling Fan Switch
What’s in the Box
Get Ready
- Download the Lumary app
- Register a Lumery account
Install
Reset and restart
Connect: Easy Mode **
CONNECT: AUTO SCAN
Connect: AP Mode
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Lumary Smart Wi-Fi Speed Ceiling Fan Switch

product

What’s in the Box

Get Ready

Tum OFF pow11r supply at the circuit breaker or fl-. Uee a noncontact voltage tester to ensure that is off. More then one disconnect switch may be n..ted to turn off pow11r.
Confirm that you are replacing uingle pole (&ingluwitch), one-way swik:h (not a 3-way switch where two switct control one fixture).
Make sure the mcisting switch box hu a neutrel wire.

Download the Lumary app

Register a Lumery account

STEP1: Enter your mobile phone number or email address.

STEP2: Enter the verification code and create a password.

Install

Step 1:

Shut off power at the circuit breaker for the switch that you are replacing. More than one disconnection maybe required to turn off power. Use a noncontact voltage tester to ensure that power is off.

Step 2:

Make sure the existing switch box has a neutral wire. Remove old switch by disconnecting all the wires. Neutral wire is typically white.

STEP 3:

Connect Switch’s neutral wire (White) to your home’s neutral wire. Connect Switch’s five wire (Black) to your home’s hot wire. Connect Switch’s Light wire (Brown) to the wire that controls the light. Connect Switch’s Fan wire (Blue) to the wire that controls the fan. Connecting the Switch’s ground wire (Green) to your home’s ground wire is optional. Check that all wire nuts are secured. Mark all wires with included stickers for next reference.

Step 4:

Use screws to secure TAP into your wall. Snap on the included faceplate.

Step 5:

Restore power by reversing step 1.

Step 6:
Once power is connected, the white indicator light will blink to indicate that TAP is ready to connect to Wi-Fi. (Please make sure both light and fan are in OFF status)

Reset and restart

QUICKTIP: On the switch faceplate, the reset button as the power reset button and the start button is also known as the Wi-Fi reset button.

How do I reset TAP and What does the blinking light means?

Reset TAP by pressing and holding the Wi-Fi reset (restart) button for 3 seconds until the indicator begins to rapidly flash. The Wi-Fi reset button is located on the bottom right side of the switch(not the switch plate) labeled “restart”

Reset one time (press and hold) to reach Easy mode.
Reset again to reach AP mode

Connect: Easy Mode **

**

STEP 1:

Open the Lumary app. In the top comer of the Devices screen, click(+). Choose “Electricien-SWitch(Wi-Fi)”, if connection fail, please try “Lighting-Lighting (Wi-Fi)”.

STEP 2:

Make sure Switch’s light is rapidly flashing white. If not, reset to reach Easy Mode to connect (Pege 9). Press “Confirm indicator rapidly blink” in the app.

STEP 3:

Enter your Wi-Fi network and password.

STEP 4:

The Lumary app will connect to your switch.

NOTE: Lumary can connect to 5GHz networ1cs. If the connection fails, try to connect using AP Mode.

CONNECT: AUTO SCAN

Step 1:

Connect your smart phone to a 2.4GHZ Wi-fi, O[pen the Lumary app, in the top right corner of screen, click (+). Choose Auto-Scan.

Step 2:

Power on the smart garage opener, press and hold the reset button for 5 seconds until it is rapidly flashing white.

Step 3:

Click start scan, the app will search for device automatically. Wait 5-20 Seconds until the device appears on the screen. Click Next, cutomize the device name as needed, then click done to complete connection.

Connect: AP Mode

Step 1:

Press and hold the restart button for 5 seconds until indicator light is rapidly flashing. then press and hold the restart button for another 5 seconds until indicator light is slowly flashing.