Johan Lewis Callum House Ceiling Pendant User Manual
- June 7, 2024
- JOHAN LEWIS
Table of Contents
User manual
Callum House
Ceiling Pendant
Thank you for purchasing this Callum House ceiling pendant.
Please read the instructions carefully before use to ensure safe and
satisfactory operations of this product. Please keep this instruction for
future reference.
Warnings!
This product is Class II = and should be fitted to a lighting Supply protected
by a 5 amp fuse or equivalent circuit breaker.
For your safety, this product must be installed in accordance with local
Building Regulations. If in any doubt, or where required by the law, consult a
competent person who is registered with an electrical self-certification
scheme. Further information is available online or by phone at your Local
Authority.
To prevent electric shock, switch off the mains supply before installing or
maintaining this product. Ensure other persons cannot restore the electricity
supply without your knowledge.
Always use the correct bulb type with the correct wattage as indicated in the
specification table.
When changing the bulb, always switch off at the mains and allow the old bulb
to cool down before handling. Dispose of used bulbs carefully.
Caution! The bulb and surrounding parts can become hot during use.
For indoor use only.
Care instructions
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as
these will damage the finish.
Replace bulbs from John Lewis or established brands of the same type and
compatibility.
Parts list
Assembly
Never install your appliance on a wet, freshly painted, or plastered surface.
Ensure the house electricity supply is switched off at the fuse box. If
removing an existing fitting, note down all wiring connections. Check the
fixings will not touch any existing wiring before drilling and attaching the
light to the ceiling.
Ensure you thread the ceiling wires through the black insulating tube fixed to
the appliance.
Step 1
Remove mounting bracket from the fitting by removing the retaining screws and
washers, retain for later. Using the mounting bracket as a template, mark and
then drill the fixing holes in the ceiling (ensure the screws are firmly fixed
into a solid or other suitable mounting and not just the plasterboard.). Take
care not to damage wiring. Attach the mounting bracket to the mounting surface
using suitable fixings. Do not attach the fitting to the mounting bracket at
this stage. Make sure no wires are trapped in the process.
Step 2
Ensuring that the power has been isolated, lever opens the terminal block box
cover with a screwdriver then feed supply cable through rubber sleeving and
make electrical connections as follows:
- Connect the supply Live (Normally brown or red) to fitting life (marked “L”)
- Connect the supply neutral (blue or black) to fitting neutral (marked “N”)
NO EARTH must be connected to any part of this fitting.
Please note that residential wiring can vary, if you are unsure about the correct polarity please consult a qualified electrician.
Height Adjustment: This fitting is height adjustable at the point of installation only. No attempt must be made to adjust the height once it has been attached to the ceiling. If adjustment is required at a later date the fitting must be isolated from the mains and removed from the ceiling first. Lay the fitting on a clear covered surface. Using a suitably sized flat-bladed screwdriver loosen the plastic screw clamp under the ceiling cup, also undo the screws or clamp located in the ceiling cup. Carefully pull the cable through the ceiling cup to the desired height and then retighten all screws to ensure that clamps are fully secured.
Step 3
The excess cable must be carefully located inside the ceiling cup or within
the ceiling void. Carefully offer fitting over mounting bracket then secure in
place with the screws and washers removed earlier.
Fit the bulb , type, and wattage as indicated on the fitting (bulb not
supplied). The wattage indicated must not be exceeded.
Once installation is complete, the house electricity may be restored at the
fuse box.
Recommended bulb
1 x 6-9 Watt E27 (ES) energy-efficient LED GLS bulb
Or
1 x 42W E27 eco halogen GLS bulb
Bulb not included
Specification
Max power: 42W
Voltage: 220~240V, 50/60Hz
IP20
Weight 0.7Kg
Please retain these instructions for future reference.
This symbol indicates that this product should not be treated as normal
household waste and should be recycled. John Lewis does not operate in-store
take back, but members of the Distributor Take-Back scheme have funded the
development and upgrade of recycling facilities across the UK. Please take it
to your
nearest collection facility or for further details contact your local council
or visit www.recycle-more.co.uk.
We have taken great care to ensure that this product reaches you in perfect condition. However, should any parts be damaged or missing please e-mail lightingparts@JLPspares.co.uk
Troubleshooting:
Why is the light not working when switched on?
Check your power supply is switched on Turn off the light and check that the
bulb is inserted correctly Check the bulb is still in working order.
John Lewis partnership
171 Victoria Street
London SW1E 5NN
Johnlewis.com
Made in China
Issue 01 09/18
References
- John Lewis & Partners | Department Store | Home, Fashion, Tech & More
- Everything you need to know to Recycle More
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>