Johan Lewis Balance 2Lt Wall Light User Manual
- June 7, 2024
- JOHAN LEWIS
Table of Contents
User manual
Balance 2Lt Wall Light
IL4282
Thank you for purchasing this Balance wall light. Please read the instructions carefully before use to ensure safe and satisfactory operations of this product. Please keep this instruction for future reference.
Warnings!
For your safety, this product must be installed in accordance with local
Building Regulations.
If in any doubt, or where required by the law, consult a competent person who
is registered with an electrical self-certification scheme. Further
information is available online or by phone at your Local Authority.
To prevent electric shock, switch off the mains supply before installing or
maintaining this product. Ensure other persons cannot restore the electricity
supply without your knowledge.
Always use the correct bulb type with the correct wattage as indicated in the
specification table. This product is Class = and should be fitted to a
lighting Supply protected by a 5 amp fuse or equivalent circuit breaker. When
changing the bulb, always switch off at the mains and allow the old bulb to
cool down before handling. Dispose of used bulbs carefully.
Caution! The bulb and surrounding parts can become hot during use.
For indoor use only.
Care instructions
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as
these will damage the finish.
Replace bulb from John Lewis or established brand of the same type and
compatibility.
Parts list
Assembly
Never install your appliance on a wet, freshly painted, or plastered surface. Ensure the house electricity supply is switched off at the fuse box. If removing an existing fitting, note down all wiring connections. Check the fixings will not touch any existing wiring before drilling and attaching the light to the ceiling. Ensure you thread the ceiling wires through the black insulating tube fixed to the appliance.
Step 1
Remove mounting bracket from the fitting by removing the retaining screws and
any washers, retain for later. Using the mounting bracket as a template, mark
and then drill the fixing holes in the wall (ensure the screws are firmly
fixed into a solid or other suitable mounting and not just the plasterboard.)
Take care not to damage wiring. Attach the mounting bracket to the mounting
surface using suitable fixings. Do not attach the fitting to the mounting
bracket at this stage. Make sure no wires are trapped in the process.
Step
2
Ensuring that the power has been isolated, connect the electrical supply wires
to the connector blocks corresponding terminals. Make the electrical
connection as follows:
• Connect the supply live (normally brown or red) to fitting live (marked “L”)
on the terminal block housing.
• Connect the supply neutral (normally blue or black) to fitting neutral
(marked “N”) on the terminal block housing.
NO EARTH must be connected to any part of this fitting. Please note that
residential wiring can vary, if you are unsure about the correct polarity
please consult a qualified electrician. Ensure electrical connections are
tight and no loose strands of wire protrude from the terminal block then close
the connector block cover by snapping back together.
Step
3
The excess cable must be carefully located inside the ceiling cup or within
the ceiling cavity itself. Carefully offer fitting over mounting bracket then
secure in place with the screws and any washers removed earlier. Fit the bulb:
type and wattage as indicated on the fitting. The wattage indicated must not
be exceeded.
Fit the shades by placing the threaded hole in the shade over the lamp holder
section and rotating it into place. If cross-threading occurs undo and start
again. Take care not to overtighten as this may cause damage to the fitting.
Once installation is complete, the house electricity may be restored at the
fuse box.
Recommended bulb
2 x 3-5 Watt G9 energy-efficient LED
Specification
Max power: 5W
Voltage: 220~240V, 50/60Hz
IP20
Weight 0.7Kg
Please retain these instructions for future reference.
This symbol indicates that this product should not be treated as normal
household waste and it should be recycled. John Lewis does not operate in-
store take back, but as a member of the Distributor Take-Back scheme has
funded the development and upgrade of recycling facilities across the UK.
Please take it to your nearest collection facility or for further details
contact your local council or visit www.recycle-more.co.uk.
We have taken great care to ensure that this product reaches you in perfect
condition. However, should any parts be damaged or missing please e-mail
lightingparts@JLPspares.co.uk
Troubleshooting:
Why is the light not working when switched on?
Check your power supply is switched on
Turn off the light and check that the bulb is inserted correctly
Check the bulb is still in working order.
John Lewis partnership
171 Victoria Street
London SW1E 5NN
Johnlewis.com
Made in China
Issue 2 09/20
References
- John Lewis & Partners | Department Store | Home, Fashion, Tech & More
- Everything you need to know to Recycle More
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>