Johan Lewis Alice Pierced Shade Floor User Manual
- June 7, 2024
- JOHAN LEWIS
Table of Contents
User manual
IL4017
ALICE PIERCED
SHADE FLOOR
Thank you for purchasing this Alice pierced shade floor lamp. Please read the
instructions carefully before use to ensure safe and satisfactory operations
of this product.
Please keep this instruction for future reference.
Warnings!
The supply cable runs through the inside of this product. Take care not to
place undue stress on the cable whilst unpacking to prevent the possibility of
a poor connection. If you are in any doubt consult a person competent to give
advice on the assembly of electrical equipment. If the external flexible cable
of the lamp is damaged it shall be exclusively replaced by the manufacturer or
his service agent or a similarly qualified person in order to avoid a hazard.
To prevent electrocution switch off at the mains supply before assembling or
maintaining this fitting. Ensure the plug is not connected to any power supply
and read instructions before assembly.
Always be sure to use the correct type and wattage of bulbs as indicated on
the fitting. Never exceed the wattage stated. When changing the bulb, always
switch off at the mains and allow the old bulb to cool down before handling.
Dispose of used bulbs carefully.
Caution! The bulb and surrounding parts can become hot during use. For
indoor use only.
Care instructions
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish. Replace bulbs from John Lewis or established brands of the same type and compatibility.
Parts list
Assembly
Never assembly your appliance on a wet, freshly painted surface. Ensure to switch off at the mains supply before assembling or maintaining this fitting.
Step 1
Unpack the product and remove all packaging. Be careful not to scratch the
surface of the product whilst removing the wrapping. Lay the product out on
the floor. If the floor is not carpeted please cover it with a soft cloth to
avoid damage to the flooring and surface of the product. Assembly should take
place with the product laying flat. Screw the lower pole onto the upper lamp
holder section ensuring that the lamp holder section is kept still and that
the pole is threaded on ensuring that the cable does not twist.
Step 2
Gently pull any excess supply cable through the small hole in the base until
it meets the pole assembly. Place the self-adhesive protective pad to the
bottom of the base.
Note: Peel the cover from the protective base pad and apply evenly. Stand
the floor lamp upright and ensure all the assembled parts are fully tightened.
Step 3
To fit shade: Lower the shade over the lamp holder section and align the
screw holes at the base of the shade with those in the frame just below the
lamp holder. Insert the three thumb screws through the underside of the lamp
holder frame section and into the threaded holes in the lower frame and
tighten screws to secure them in place.
Fit the bulb, type, and wattage as indicated on the fitting (bulb not
supplied). The wattage indicated must not be exceeded. The floor lamp is now
ready for use.
Recommended bulb
2 x 3-4 Watt SES energy-efficient LED CNDL
or
2 x 28 Watt SES eco halogen CNDL
Bulb not included
Specification
Max power: 28W
Voltage: 220~240V, 50Hz
IP20
Weight 2.4Kg
Please retain these instructions for future reference.
This symbol indicates that this product should not be treated as normal
household waste and it should be recycled. John Lewis does not operate in-
store take back, but as members of the Distributor Take Back scheme have
funded the development and upgrade of recycling facilities across the UK.
Please take it to your nearest collection facility or for further details
contact your local council or visit www.recycle-more.co.uk.
We have taken great care to ensure that this product reaches you in perfect
condition. However, should any parts be damaged or missing please e-mail
lightingparts@JLPspares.co.uk
Troubleshooting:
Why is the light not working when switched on?
Check your power supply is switched on
Turn off light and check that the bulb is inserted correctly
Check the bulb is still in working order.
John Lewis partnership
171 Victoria Street
London SW1E 5NN
Johnlewis.com
Made in China
Issue 2 05/18
References
- John Lewis & Partners | Department Store | Home, Fashion, Tech & More
- Everything you need to know to Recycle More
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>