TAC 72330B Bull Bar Steelcraft Instruction Manual

: June 7, 2024
: TAC

Table of Contents

TAC 72330B Bull Bar Steelcraft
Product Information
Product Usage Instructions
PARTS LIST
PROCEDURE
Passenger/right Side Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TAC 72330B Bull Bar Steelcraft

TAC-72330B-Bull-Bar-Steelcraft-product

Product Information

Specifications:

Model: 3 BULL BAR
Compatible Vehicles: 21-24 GRAND CHEROKEE L, 22-24 GRAND CHEROKEE, 22-24 GRAND CHEROKEE 4xe
Part Number: 72330B
Manufacturer Website: www.tacautoparts.com

Parts List:

1 Bull Bar
1 Driver/Left Frame Mounting Bracket
1 Passenger/Right Frame Mounting Bracket
4 10-1.5mm x 35mm Hex Bolts
8 10mm x 30mm x 2.5mm Flat Washers
4 10mm Lock Washers
4 10mm Hex Nuts

Product Usage Instructions

Remove the plastic splash guard from the vehicle.
Identify and locate the mounting bolts on the passenger/right side bumper end.
Trace and cut out a section of the bumper cover to fit the Frame Mounting Brackets.
Attach the Frame Mounting Brackets to the bumper using the provided hardware.
Securely attach the Bull Bar to the Mounting Brackets with assistance.
After installation, wax the product for protection. Regular waxing is recommended for maintenance.

Note: For stainless steel finishes, use aluminum polish for scratches and mild soap for cleaning. For gloss black finishes, mild soap is recommended for cleaning.

FAQ:

Q: Is professional assistance recommended for installation?
A: Yes, assistance is recommended for installation to ensure proper fit and secure attachment.
Q: What should I do to protect the finish of the product?
A: Regular waxing with a non-abrasive wax is recommended to protect the finish. Avoid using polishes containing abrasives.

INSTALLATION INSTRUCTIONS

3” BULL BAR
21-24 GRAND CHEROKEE L
22-24 GRAND CHEROKEE
22-24 GRAND CHEROKEE 4xe
PART# 72330B

PARTS LIST

$TAC-72330B-Bull-Bar-Steelcraft-fig- $1$$

1 Bull Bar
1 Driver/Left Frame Mounting Bracket
1 Passenger/Right Frame Mounting Bracket
4 10-1.5mm x 35mm Hex Bolts
8 10mm x 30mm x 2.5mm Flat Washers
4 10mm Lock Washers
4 10mm Hex Nuts

PROCEDURE

REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED. CUTTING IS REQUIRED

Remove the plastic splash guard, (Figure 1). Pay close attention to the type and location of all factory hardware for easier reinstallation.
Locate the large (21mm) and small (16mm) mounting bolts attaching the passenger/right sideouter bumper end to the inner impact bumper, (Figure 1). NOTE: The “small” 16mm hex bolt is visible, the larger hex bolt is partially hidden behind the plastic bumper cover.
Select the passenger/right side Frame Mounting Bracket, (Figure 2). Hold the Bracket in place over the hex bolts. Trace the outline of the Bracket onto the plastic cover, (Figure 3). Use a sharp knife or hacksaw blade to cut out a small section of the bumper cover, (Figure 4).
Remove the smaller forward hex bolt. Loosen but do not remove the larger rear hex bolt. Slid the rear slot end of the Bracket under the larger bolt, (Figure 4). Reinstall the smaller hex bolt to attach the Bracket. Snug but do not fully tighten hardware at this time.
Repeat Steps 3—5 to attach the driver/left side Frame Mounting Bracket.
With assistance, hold the Bull Bar up to the inside of the Mounting Brackets. Attach the Bull Bar to the Mounting Brackets with the included (4) 10mm x 35mm Hex Bolts, (8) 10mm Flat Washers, (4) 10mm Lock Washers, and (4) 10mm Hex Nuts, (Figures 5 & 6).
Align and adjust the Bull Bar and tighten all hardware. Reinstall the rear of the splash guard.Hold the front of the splash guard up to the bottom of the Brackets, (Figure 6). Cut slots in the splash guard to clear the Brackets. Fully reinstall the splash guard.
Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installation. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to clean the Bull Bar.
For gloss black finishes: Mild soap may be used to clean the Bull Bar.