MI Smart Projector Pro 2 User Manual

June 7, 2024
Mi

MI Smart Projector Pro 2 User Manual

MI Smart Projector Pro 2 User Manual

User Notice

Thank you for choosing the Mi Smart Projector 2 Pro. Read this manual carefully before use, and retain it for future reference. Illustrations of product, accessories and user interface in the user manual are for reference purposes only. Actual products and functions may vary due to product enhancements.

Regulatory Compliance

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as the terms and conditions of such collection points.
Hereby, [Fengmi (Beijing) Technology Co., Ltd.] declares that the radio equipment type [Mi Smart Projector 2 Pro/XMTYY02FM] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.mi.com/global/service/support/declaration.html This device is restricted to indoor use when operating in the 5150 to 5350 MHz frequency range. Operation Frequency: 2.4 GHz­2.4835 GHz (for Bluetooth) Maximum RF Power Output: < 10 mW (for Bluetooth) Operation Frequency: 2.4 GHz­2.4835 GHz (for Wi-Fi 2.4 GHz) Maximum RF Power Output: < 100 mW (for Wi-Fi 2.4 GHz) Operation Frequency: 5.15 GHz­5.35 GHz and 5.47 GHz­5.725 GHz (for Wi-Fi 5 GHz) Maximum RF Power Output: < 200 mW (for Wi-Fi 5 GHz)
Note: Under normal use of conditions, this equipment should be kept at a separation distance of at least 20 cm between the antenna and the body of the user.

Safety Instructions

Before using the product, please carefully read the following safety instructions.

This warning symbol informs the user that this product contains non-insulated voltage sources that can cause an electric shock. Coming into contact with any internal component may result in an electric shock.

This symbol informs the user about important handling and maintenance-related information. Please read this information carefully to ensure proper use.

This symbol informs the user to be aware of high temperatures.

This symbol informs the user to avoid touching this part.

Grounding Warning: This product must be grounded when in use.

Transportation Instructions: It is recommended to transport this projector in its original or similar packaging.
Preventing Electric Shocks and Fire Hazards:

– Using an incorrect power cord may result in decreased product performance and even electric shock or fire. To ensure the projector’s performance and safety, only use its original power cord or an identical replacement.
– If you use an extension cord, it must not have a current rating lower than the projector’s original power cord. Failure to heed this warning may result in the extension cord overheating and could pose hazards such as electric shock and fire.
– To avoid damage caused by a power surge or lightning strike, unplug the projector from the power outlet during thunderstorms or when it is not in use for a long time.
– Do not place any flammable objects near this projector so as to avoid fire.
– Do not block the lens with any object when the projector is turned on. Any object placed close to the lens may get very hot and/or deformed, and may even cause a fire.
– Do not block any of the vents of the projector, as this may cause a buildup of heat within the product and result in a fire.
Safety Precautions:
– Do not place this projector on an unstable platform, stand or table so as to prevent it from falling and causing serious damage or personal injury.
– Do not look directly into the lens when the projector is turned on to avoid eye damage.
– Do not attempt to disassemble this projector as it may contain dangerous high voltage components. This projector must only be maintained and repaired by a qualified or authorized technician.
– Do not place this projector in an upright position, as it may fall over and cause injury or damage.
– Do not expose this projector to rain or moisture (operating humidity is 20%­80%).
– Do not immerse this projector in, nor expose it to water or other liquids. Immediately unplug the projector if any liquid or object got into its housing, and have it checked by a qualified technician before using it again.
– Do not place this projector in any of the following environments:

  • In poorly ventilated or narrow spaces.
  • Near devices that produce a strong magnetic field.
  • In direct sunlight.
  • Close to a fire alarm.
  • In extremely hot, cold, or humid environments.

Caution:

– Risk of explosion if the battery is replaced by an incorrect type.
– Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
– Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
– A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.

Caution:
As with any bright light source, do not stare into the beam, RG2 IEC 62471-5:2015

Caution
Do not stare into the beam
RG2

Package Contents

MI Smart Projector Pro 2 User Manual - Package
contents

Note:
– The actual contents may vary depending on the country (or region) of sale, please refer to the actual product.
– Retain the original packaging for future storage or transportation.

Product Overview

Exterior
![MI Smart Projector Pro 2 User Manual - Product Overview](https://manuals.plus/wp-content/uploads/2021/07/MI-Smart-Projector-Pro-2-User-Manual-Product-Overview.jpg)

Note

– Do not place any flammable objects near the heat dissipation vent.
– Do not place any objects near the vents, as this may cause heat to build up inside the projector.
– Do not look directly into the lens so as to avoid eye damage as this projector emits strong light during use.
Suspended installation note:
– Please use the specified screws: M4 × 8 mm, 4 pcs.
– Remove the rubber plugs from the feet on the bottom to access the threaded holes.
– Please choose an appropriate suspension bracket.

Connection Ports

MI Smart Projector Pro 2 User Manual - Connection
Ports

  1. Power Port

  2. HDMI input port 2

  3. HDMI input port 1
    / Audio return channel port

  4. Supports USB 2.0 communication protocol

  5. Supports USB 2.0 communication protocol

  6. Audio output port

  7. Optical digital audio signal output port

  8. Ethernet port

Power Indicator

MI Smart Projector Pro 2 User Manual - Power Indicator

The power indicator (white light) indicates the projector status as follows:
– While turning on the projector, the indicator light will blink.
– After loading the system, the indicator light will turn off.
– After turning off the screen, the indicator light will turn on.
– After shutting down the system, the indicator light will turn off.

Remote Control

MI Smart Projector Pro 2 User Manual - Remote Control

Note:
– Pay attention to the positive and negative poles when installing batteries in the remote control.
– When the battery leaks, immediately wipe away any fluid with a dry cloth and replace the batteries with new ones.
– Dispose of used batteries according to local waste disposal rules and regulations of the country or area you live in.

Projection Distance & Screen Size

MI Smart Projector Pro 2 User Manual - Projection Distance & Screen
Size

Determine the distance between the projector and the wall or screen according to the desired screen size.

MI Smart Projector Pro 2 User Manual - Determine the distance
table

Screen Dimensions (SD): The diagonal size of the projection screen (in inches). Relative Distance (D): The distance between the projector and the wall or screen (in cm). Relative Height (H): The distance from the bottom of the projector to the bottom edge of the projected image (in cm).

Note: The dimensions in the table above are for reference only, they are approximate and may slightly differ from the actual values.

How to Use

Pairing the Remote Control

MI Smart Projector Pro 2 User Manual - Pairing the Remote
Control

After installing the batteries in the remote control, press the OK button to start pairing.

MI Smart Projector Pro 2 User Manual - Point the remote at the bottom right
corner of the projector

Point the remote at the bottom right corner of the projector, then simultaneously press and hold the APP and the Home button. Once you hear a beep, it indicates that the pairing process has started. Release the buttons and wait for the process to complete.

MI Smart Projector Pro 2 User Manual - A notification will appear on the
projected image

A notification will appear on the projected image once the remote control has been paired successfully.

Note: Keep the remote control within 20 cm of the projector during the pairing process.

Image Focus

Go to Settings > Projector > Focus and select Execute Focus, the screen will focus and once it is finished you can press the left or right button on the remote control for further fine-tuning.

MI Smart Projector Pro 2 User Manual - image Focus

Go to Settings > Projector > Focus and select the Auto Focus switch, when it is enabled, moving the projector will automatically trigger the screen to focus, and you can also change the Auto Focus Method between Camera Focus and Instant Focus.

If there is an issue with Instant Focus, you can go to Settings > Projector > Focus to select Instant Focus Calibration, and follow the instructions to complete the Instant Focus Calibration.

Keystone Correction

Go to Settings > Projector > Keystone Correction > Keystone Correction, and use the up and down buttons to select Quick Adjustment, Fine Tuning, and Reset, then press the OK button to enter the correction mode.

MI Smart Projector Pro 2 User Manual - Keystone
Correction

If the projector is moved, it will start automatic keystone correction and the projected image will be adjusted automatically.
Note: Go to Settings > Projector > Keystone Correction, to configure Auto Keystone. Auto Keystone is enabled by default.

Bluetooth Speakers

The projector has four high-quality built-in speakers with a total output of about 20 W. The speakers can also be used as a standalone Bluetooth stereo.
To use speakers as the Bluetooth stereo, select Settings > Remotes & Accessories > Bluetooth speaker mode. Enable the Bluetooth function on your phone. Search and locate the projector name in the Bluetooth list, then pair the projector with your phone.

MI Smart Projector Pro 2 User Manual - Bluetooth
Speakers

Note:
To connect and pair with other Bluetooth devices such as speakers and earphones, select Settings > Remotes & Accessories > Add accessory. Make sure the device is in an awaiting connection mode with its Bluetooth function enabled.

Smart Temperature Control

The projector automatically monitors the ambient temperature (operating temperature range is 0°C to 40°C), and the projector’s fan speed is automatically adjusted based on the detected temperature values.
The projector has two brightness modes to choose from when operating at a normal temperature. To adjust the projector’s brightness level, go to Settings

Image > Brightness Mode.
If the projector gets too hot, and an overheating warning will appear and the projector will automatically switch to low brightness mode. Temperature and error warnings will be displayed automatically whenever the temperature exceeds its maximum range to inform you that the projector will be automatically turned off.

Care & Maintenance

Heat Dissipation Maintenance
![MI Smart Projector Pro 2 User Manual - Heat Dissipation Maintenance](https://manuals.plus/wp-content/uploads/2021/07/MI-Smart-Projector-Pro-2-User-Manual-Heat-Dissipation-Maintenance.jpg)
Cleaning & Maintenance

MI Smart Projector Pro 2 User Manual - Cleaning &
Maintenance

Turn off and unplug the projector before cleaning.

Note: Avoid touching the heat dissipation vent on the rear, as it can become very hot.

Note: Do not place any objects within 20 cm of the projector’s air vents, as this will affect the heat dissipation effect.
Only use the cleaning cloth that comes with the projector or a professional- grade cleaning cloth to clean the projector’s glass. Do not use any abrasive cleaning products, solvents, chemicals, or other rough objects so as to avoid scratches or corrosion.

Note:
– The projector is not water-resistant. Do not allow liquids to penetrate the projector, especially areas such as the power indicator, lens, air vents, connection ports, and speaker grilles.
– Only use the cleaning cloth that comes with the projector or a professional grade cleaning cloth to clean the projector’s lens. 15

Specifications

MI Smart Projector Pro 2 User Manual - Specifications MI Smart Projector Pro 2 User Manual -
Specifications

Troubleshooting

MI Smart Projector Pro 2 User Manual - Troubleshooting

Product Certification

MI Smart Projector Pro 2 User Manual - Product
Certification

http://patents.dts.com.

Manufactured for: Xiaomi Communications Co., Ltd.
Manufactured by: Fengmi (Beijing) Technology Co., Ltd.
(a Mi Ecosystem company)
Address: 301, 3F, Building 3, No.10, Barracks South Street,
Renhe Town, Shunyi District, Beijing, China

For further information, please go to www.mi.com

Importer:
Beryko s.r.o.
Na Roudné 1162/76, 301 00 Plzen
www.beryko.cz

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals