DENVER LED Smart Tv User Manual
- June 7, 2024
- Denver
Table of Contents
DENVER LED Smart Tv
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS – PLEASE READ CAREFULLY BEFORE USE.
The following safety instructions are located on the back of the TV.
| DANGER OF ELECTRIC SHOCK! NEVER REMOVE THE SCREWS OF THE COVER. NO USER-
SERVICEABLE PARTS IN THE DEVICE. REPAIR ONLY BY QUALIFIED SERVICE PERSONNEL.
---|---
| The exclamation mark in the equilateral triangle indicates important
operating and maintenance instructions
| The flash in the equilateral triangle indicates high voltage in the device,
which can lead to electric shock
Please follow the instructions below:
- Do not use this TV near water.
- Only clean the device with a damp cloth.
- Do not block any ventilation openings.
- Set up the television in accordance with the supplied quick guide and these operating instructions.
- Lay the power cable so that it cannot be stepped on or pinched. Pay special attention to the plug and the point at which the cable is led out of the television.
- Do not let the power cord hang over the edge of the table.
- Disconnect the TV from the mains if there is a thunderstorm or if it is not used for a long period
| WARNING! EXPOSE THE TELEVISION TO AVOID FIRE OR ELECTRIC SHOCK OR RAIN
OR MOISTURE. THE TELEVISION SHOULD NEVER BE EXPOSED TO SPLASH / DRIP WATER AND
NO OBJECTS FILLED WITH LIQUID ON THE TELEVISION
---|---
NOTE: Open flames (such as candles) should never be placed on the TV
Smells from the TV
New TVs can cause unusual smells when they are switched on for the first time.
Due to the manufacturing process of the components, the television and other
electronic products may have parts that produce odors when they are first
turned on and warmed up.
The smell usually disappears after a few days of use and does not return.
This is normal and occurs with many electronic devices. Ensure that there is
sufficient ventilation in and around the device so that the smell can
disappear.
EXTERNAL SCHEMATIC AND INSTALLATION
SCART: AV input from a device like VCR
Coax Out: Digital Audio Output from TV
DVB-S: Connect RF signal from satellite/DVB-S
DVB-T: Connect Analog/ATV signal or Digital/ DVB-T or DVB-C signal
HDMI1/HDMI2: Connect HDMI input signal from signal source such as DVD
USB: USB support multimedia playback and software upgrade
CI Slot: Insert CI card for Digital TV
Mini AV In: Mini AV input from video playback device
Mini YPbPr In: Mini component input from a video playback device
Earphone Out: Audio output from TV through Earphone
Antenna/Cable Connection
a. Connect the Plug of the antenna cable or CATV cable to the cable (not
provided with this unit), then connect to the antenna input of this unit for
best reception.
b. If the antenna cable in your home is other than the above two or you
have problems in installing the antenna, please contact your dealer.
Notes:
a. Current outdoor antenna or cable TV use 75 OHM coaxial antenna cable.
For better reception suggest this kind of antenna cable
b. Flat cable or indoor antenna are old designed, the reception may not
be good enough
REMOTE CONTROLLER
-
POWER( )
Press to turn the TV on or off (Standby). -
MUTE ( )
Press to mute or restore the volume. -
PROGRAM SELECT (0-9)
Press to select the TV channel directly. -
RECALL
Press to return to the previously viewed channel/ Press to back in previous state (Optional). -
DISPLAY
Press to display relevant information such as screen format, source, etc. -
MENU
Press to enter or exit from the TV menu. -
INPUT
Press to select the input source mode. -
UP/DOWN/LEFT/RIGHT Cursor
(▲/▼/►/►)
Navigate the menu. -
ENTER
Press to confirm and execute the selection. -
EPG
Display the EPG interface in DTV mode -
VOLUME UP/DOWN (V+/V-)
Press to adjust the volume. -
PROGRAM UP/DOWN (CH+/CH-)
Press to select previous/ next channel. -
FREEZE
Press to hold/ freeze the current screen without update & change. Press again to release the freeze state (RF Source only.) -
USB
Press to select USB mode directly (Optional). -
Picture Mode {P.M.)
Press to select the desired picture mode. -
ASPECT
Press to select the desired picture aspect ratio. -
Sound Mode (S.M.)
Press to select the desired sound mode. -
CHN LIST
Press to go to channel list. -
EXIT
Press to exit default browser. -
FAV
Press to view your favorite channel list. -
*USB Play Control Buttons Play & Pause ( )
Press to stop the running media file.
Stop ( )
Press the stop button to exit full-screen
playback, access to the preview.
Fast Backward Button ( )
Press to fast reverse.
Fast Forward ( )
Press to fast forward.
Previous ( )
Press to play the previous file.
Next** ( )
Press to play the next file. -
TV/RADIO
Switch between TV and Radio -
Color Buttons (R,G,Y,B)
TITLE: Shows the tile of the media
GOTO: Go to the desired time REPEAT: Repeat the media playback
A-B: A-B Repeat function enables playback to a specific section repeatedly by setting the start point (A) and end point (B) -
Teletext Keys
TV/TXT: Load or exit teletex menu
CANCEL: Back to TV Program while searching a teletext page
REVEAL: Display or hide hidden information
NICAM/A2 : Select the desired sound playback depending on the channel
SOURCE
Press INPUT button to display the input source list
Press ▼ / ▲ or OK button to select the input
source you want
Press OK button to enter the input source
Press EXIT button to quit
BASIC OPERATION
First Time Installation
Connect an RF cable from the TV’s input called “RF-In” and to your TV Aerial socket.
Select Language
Press ◄ / ► button to select the language to be used for menus and message.
Select Country
Press ▼ / ▲ button to highlight country menu.
Press ◄ / ► button to select the country you want to
Auto Tuning
First tuning ATV, press Menu and left arrow button to skip ATV tuning, Second
tuning DTV, press Menu and left arrow button to skip DT
Setup
Press MENU button to display the main menu.
Press ◄ / ► button to select SETUP in the main menu.
Press ▼ / ▲ button to select the option that you want to adjust in the
SETUP menu.
Press Enter button to adjust.
After finishing your adjustment, Press Enter button to save and return to
the previous menu.
Language
Select an OSD menu language can be displayed. Default English is selected as
menu language.
Press ▼ / ▲ / ◄ / ► button to select Menu Language.
TT Language
Press ▼ / ▲ button to select TT Language, then press Enter button to enter
sub-menu.
Press ▼ / ▲ / ◄ / ► button to select TT language.
Audio Languages
Press ▼ / ▲ button to select Audio Languages, then press Enter button to
enter sub-menu.
Press ◄ / ► button to select the primary of Audio Languages.
Press ▼ / ▲ / ◄ / ► button to select the Audio Languages
Subtitle Language
Press ▼ / ▲ button to select Subtitle Language, then press Enter button to
enter sub-menu.
Press ◄ / ► button to select the primary of Subtitle Language.
Press ▼ / ▲ / ◄ / ► button to select the Subtitle Language.
Hearing Impaired
Press ▼ / ▲ button to select Hearing Impaired, then press Enter button to
select On or Off.
PVR File System
Press ▼ / ▲ button to select PVR File System, then press Enter button to enter
sub-menu.
Press ▼ / ▲ button to select Check PVR File System, Then press Enter button to
enter, it will check the USB speed.
Aspect Ratio
Press ▼ / ▲ button to select Aspect Ratio, then press Enter button to enter
sub-menu.
Press ▼ / ▲ button to select aspect ratio. (Available options are: Auto, 4:3,
16:9, Zoom1, Zoom2)
Blue Screen
Press ▼ / ▲ button to select Blue Screen, then press Enter button to select On
or Off.
First Time Installation
Press ▼ / ▲ button to select First time installation, then press Enter button
to enter. Reset Press ▼ / ▲ button to select Reset, then press Enter button to
enter sub-menu.
Software Update (USB)
Press ▼ / ▲ button to select Software Update (USB), plug your USB device in
the USB slot, then press Enter button to update the right software.
HDMI CEC Press ▼ / ▲ button to select HDMI CEC, then press Enter button
to enter the sub menu.
HDMI CEC Press ◄ / ► button to turn the HDMI CEC On or Off.
HDMI ARC Press ◄ / ► button to turn the HDMI ARC On or Off.
Auto Standby Press ◄ / ► button to turn the Auto Standby On or Off.
Device List Press Enter button to open the main menu of device.
Picture
Press MENU button to display the main menu.
Press ◄ / ► button to select PICTURE in the main menu
Press ▼ / ▲ button to select the option that you want to adjust in the
PICTURE menu.
Press OK button to adjust.
After finishing your adjustment, Press MENU button to save and return back
to the previous menu
Picture Mode
Press ▼ / ▲ button to select Picture Mode, then press OK button to enter
sub-menu.
You can change the value of contrast, brightness, color, sharpness and tint
when the picture is in Personal mode.
TIPS: You can press PMODE button to change the Picture Mode directly
Contrast/ Brightness/ Color/ Tint / Sharpness
Press ▼ / ▲ button to select option, then press ◄ / ► button to adjust.
Contrast Adjust the highlight intensity of the picture, but the shadow of
the picture is invariable.
Brightness Adjust the optical fiber output of the entire picture, it will
affect dark region of the picture.
Color Adjust the saturation of the picture based on your own liking
Tint Use in compensating color changed with the transmission in the NTSC
code.
Sharpness Adjust the peaking in the detail of the picture
Color Temp
Change overall color cast of the picture
Press ▼ / ▲ button to select Color Temperature, then press OK button to enter
sub-menu.
Press ▼ / ▲ button to select Color Temperature. (Available Picture mode: Cold,
Normal, Warm).
Change the value of red, green and blue when the color temperature is in
User mode
Cold Increase the blue tone for the white.
Normal Set to default color temperature.
Warm Increase the red color for the white
Noise Reduction
Filter out and reduces the image noise to improve picture quality.
Press ▼ / ▲ button to select Noise Reduction , then press OK button to
enter sub-menu.
Off Select to turn off video noise detection.
Low Detect and reduce low video noise.
Middle Detect and reduce moderate video noise.
High Detect and reduce enhanced video noise.
Default Set as Default.
Sound
Press MENU button to display the main menu.
Press ◄ / ► button to select SOUND in the main menu
Press ▼ / ▲ button to select the option that you want to adjust in the
SOUND menu.2.
Press Enter button to adjust.
After finishing your adjustment, Press Enter button to save and return to
the previous menu
Sound Mode
Press ▼ / ▲ button to select Sound Mode, then press Enter button to enter sub-
menu.
Press ▼/▲ button to select.
You can change the value of Treble and Bass when the sound is in Personal
mode.
TIPS: You can press SMODE button on the remote control to change the
Sound Mode directly.
Standard Produces a balanced sound in all environments.
Music Preserves the original sound. Good for musical programs.
Movie Enhances treble and bass for a rich sound experience.
Sports Enhances vocals for sports.
Personal Select to customize sound settings
Note: The treble and bass are only available in Personal mode, you
can adjust them as you like.
Balance
Press ▼ / ▲ button to select option, Press ◄ / ► button to adjust.
Auto Volume level
Press ▼ / ▲ button to select Auto Volume Level, then press ◄ / ► button to
select On or Off.
SPDIF Mode
Press ▼ / ▲ button to select SPDIF Mode, then press ◄ / ► button to select Off
/ PCM / Auto AD Switch
Press ▼ / ▲ button to select AD Switch, then press ◄ / ► button to select On
or Off.
Amblyopia function for the blind, the tracks will be mixed describe the
current screen.
It needs code stream to support.
Note:
Balance: This item can adjust the speaker’s output, it enables you to
listen to best at your position.
Auto Volume: This item is used for reducing the difference between
channel and program’s volume automatically.
Channel
Press MENU button to display the main menu.
Press ◄ / ► button to select CHANNEL in the main menu
- Press ▼ / ▲ button to select the option that you want to adjust in the CHANNEL menu.
- Press Enter button to adjust.
- After finishing your adjustment, Press Enter button to save and return to the previous menu
Auto Tuning
Press ▼ / ▲ button to select Auto Tuning, then press Enter/► button to enter
ATV Manual Tuning
Current CH >
Set the channel number.
Color System >
Select the color system
Sound System >
Select the Sound system
Fine-Tune >
Adjust the frequency of the channel finely.
(Available System: AUTO, PAL , SECAM )
Search >
Start searching channel
DTV
Press ▼ / ▲ button to select Manual Tuning, then press Enter button to enter
sub-menu.
Press ◄ / ► button to select channel, then press Enter button to search
program.
Manual Tuning
Program Edit
Press ▼ / ▲ button to select Program Edit, then press Enter button to
enter sub-menu
The three colored key is the shortcut key for programming the channel
First press ▼ / ▲ to highlight the channel you want to select, then:
Press the Red button to delete the program in the list.
Press the Yellow button to move the channel in favorite list.
Press the Blue button to skip the selected channel.
Press Fav button to add or remote the channel to your favorite list.
(Your TV set will skip the channel automatically when using CH+/- to view the
channels.)
Schedule List
Press ▼ / ▲ button to select Schedule List, then press Enter button to enter
sub-menu.
It is available in source
Press the YELLOW button to enter the interface below:
When the time appointment is conflict, it will produce a warning message:
Signal Information
Press ▼ / ▲ button to select Signal Information, press the Enter
button to see the detail information about the signal. Only available when
there is signal in DTV.
The CHANNEL List in Satellite Source
Auto Tuning
Press ▼ / ▲ button to select Auto Tuning, then press Enter/► button to enter
Dish Setup
Press ▼ / ▲ button to select Dish Setup, and then press Enter/► button to
enter.
Press MENU button to call out the main menu.
Highlight “Channel” using navigation buttons and press OK to enter it.
Then highlight “Dish Setup” and press OK to enter it.
Press LEFT/RIGHT navigation button to highlight Left, Middle or Right column.
Press EXIT button to return.
A. When the “Satellite” column is highlighted:
-
Press YELLOW button to enter Add menu.
Satellite Name
Press RIGHT navigation button to enter rename page.
Use navigation buttons to complete a new name.
Longitude Direction
Press LEFT/RIGHT navigation button to select desired option.
Longitude Angle
Press LEFT/RIGHT navigation button to move the cursor and press number buttons on remote control to input desired value.
Band
Press LEFT/RIGHT navigation button to select desired option. -
Press GREEN button on remote control to enter Edit menu.
The operations of Edit menu are the same as Add menu. -
Press BLUE button on remote control to enter Scan menu.
Press UP/DOWN navigation button to highlighted desired item.
Press RIGHT navigation button to select desired Scan Mode, Channel Type and Service Type. -
Press RED button to delete
Press EPG button to switch satellite and Transponder.
B. When the “Transponder” (Middle) column is highlighted:
-
Press YELLOW button on remote control to enter Add menu.
Frequency
Press LEFT/RIGHT navigation button to move the cursor and press number buttons on remote control to input desired value.
Symbol (ks/s)
Press LEFT/RIGHT navigation button to move the cursor and press
number buttons on remote control to input desired value.
Polarity
Press LEFT/RIGHT navigation button to select desired option -
Press GREEN button on remote control to enter Edit menu
The operations of Edit menu are the same with Add menu. -
Press BLUE button on remote control to enter Scan menu.
Press UP/DOWN navigation button to highlighted desired item.
Press LEFT/RIGHT navigation button to select desired Scan Mode, Channel Type and Service Type
C. When the “Ku_ASTRA…” (Right) column is highlighted:
LNB (Low Noise Block) Type
Press LEFT/RIGHT navigation button to enter submenu. Then use UP/DOWN
navigation button to select desired option.
LNB Power
Press LEFT/RIGHT navigation button to select desired option.
22 kHz
Press LEFT/RIGHT navigation button to select desired option.
Toneburst
Press LEFTRIGHT navigation button to select desired option.
DisEqc1.0 (Digital Satellite Equipment Control)
Press LEFT/RIGHT navigation button to select desired option.
DisEqc1.1
Press LEFT/RIGHT navigation button to select desired option.
Motor
Press LEFT/RIGHT navigation button to select desired option
EPG
Press EPG in the remote control to record the programs.
Press UP/DOWN navigation button to select preferred program.
Press LEFT/RIGHT navigation button to switch between left column and right
column.
When a program is highlighted (cursor moved to Right column):
Press RED button to record program.
Press GREEN button repeatedly to set a reminder.
Press YELLOW button to display program guide of previous day.
Press BLUE button to display program guide of next day.
Time
Press MENU button to display the main menu.
Press ◄ / ► button to select TIME in the main menu.
Press ▼ / ▲ button to select the option that you want to adjust in the
TIME menu.2. Press Enter button l to adjust.
After finishing your adjustment, Press Enter button to save and return to the
previous menu
Off Time Press ◄ / ► button to select On/Off
On Time Press ◄ / ► button to select On/Off
Time Zone Press ▼ / ▲ button to select Time Zone, then press Enter
button to enter sub-menu.
Press ▼ / ▲ / ◄ / ► button to select time zone
Sleep Timer
Press ▼ / ▲ button to select Sleep Timer, then
press Enter button to enter sub-menu.
Press ▼ / ▲ button to select.
(Available options are: Off,10min,20min,30min,60min,90min,
120min,180min,240min).
Auto Standby
Press ▼ / ▲ button to select Auto Standby, then press ENTER button to enter
sub-menu
Press ▼ / ▲ button to select
Tips: The remote control does not make any operation in the hypothesis time,
it will close down automatically. If you do any operation, it will reset time.
OSD Timer
Press ▼ / ▲ button to select OSD Timer, then press ENTER button to enter sub-
menu
Press ▼ / ▲ button to select
Lock
Press MENU button to display the main menu.
Press ◄ / ► button to select Lock in the main menu
Press ▼ / ▲ button to select the option that you want to adjust in the LOCK
menu.
Press Enter/◄ / ► button to adjust.
After finishing your adjustment, Press MENU button to return back to the
previous menu
System Lock
Press ▼ / ▲ button to select System Lock, Then press ENTER button to make
following four options valid.
Default Password is 0000, if you forget what you set, please call service
center.
Set Password
Press ▼ / ▲ button to select Set Password, then press Enter button to enter
sub-menu to set new password.
Channel Lock
Press ▼ / ▲ button to select Channel Lock then press Enter button to enter
sub-menu to select.
Press GREEN button to lock or unlock the channel.
Parental Guidance
Press ▼ / ▲ button to select Parental Guidance, then press Enter button to
enter sub-menu to select the number of age which is suitable for your
children.
Key Lock
Press ▼ / ▲ button to select Key Lock, then press ◄ / ► button to select Off
or On.
When Key Lock’s statue is on, you can’t use the Key panel button.
Ho tel **
**
Press ▼ / ▲ button on the remote control to select hotel mode in the Lock
menu.
Press Enter button on the remote control to enter the sub-menu.
After finishing your adjustment, Press MENU button to save and return back to
the previous menu.
Hotel Mode
Press ▼ / ▲ button to select Hotel Mode, then press ◄ / ► button to select on
or off.
Source Lock
Press ▼ / ▲ button to select Source Lock to lock the source you want, then
press Enter button to enter sub-menu to select.
Default Source
Press ▼ / ▲ button to select Default Source, then press ENTER button to
enter sub-menu to select.
Default Prog
Press ▼ / ▲ button to select Default Prog, then press ◄ / ► button to adjust.
It is available when the default source is TV.
Max Volume
Press ▼ / ▲ button to select Max Volume, then press ◄ / ► button to adjust.
Clear Lock
Press ▼ / ▲ button to select Clear Lock, then press Enter button to clear
the setting you have done before
MULTIMEDIA OPERATION
Media
Note: Before operating Media menu, Plug in USB device, then press INPUT
button to set the Input Source to Media .
Press ▼ / ▲ button to select Media in the Source menu, then press Enter button
to enter.
Press ◄ / ► button to select the option you want to adjust in the main Media
menu, then press Enter button to enter.
Movie
Press ◄ / ► button to select MOVIE in the main menu, then press Enter button
to enter.
Press Exit button to return to the previous menu and exit menu to quit. Press
◄ / ► button
to select drive disk you want to watch, then press Enter button to enter.
Press media button to play the selected movie.
Press display button to select menu in the bottom you want to run, then press
Enter button to operate.
Press Exit button to back to the previous menu and exit button to quit the
entire menu
Music
Press ◄ / ► button to select MUSIC in the main menu, then press Enter button
to enter.
Press Exit button to return to the previous menu and exit menu to quit.
Press ◄ / ► button to select drive disk you want to watch, then press Enter
button to enter.
Press ◄ / ► button to select return option to the previous menu.
Photo
Press ◄ / ► button to select PHOTO in the main menu, then press Enter button
to enter.
Press Exit button to return to the previous menu and exit menu to quit.
Press ◄ / ► button to select the file you want to watch in the file selecting
menu, then press media button to display picture.
When highlighting the option you select, the file information will appear on
the right and picture will be previewed in the center.
Text
Press ◄ / ► button to select TEXT in the main menu, then press Enter button to
enter.
Press Exit button to return to the previous menu and exit menu to quit.
Press ◄ / ► button to select drive disk you want to watch, then press Enter
button to enter.
Press ◄ / ► button to select return option to back to the previous menu.
ENERGY LABEL
Please notice – All products are subject to change without any notice. We take reservations for errors and omissions in the manual.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S
Electric and electronic equipment and included batteries contains materials,
components and substances that can be hazardous to your health and the
environment, if the waste material (discarded electric and electronic
equipment and batteries) is not handled correctly.
Electric and electronic equipment and batteries is marked with the crossed out
trash can symbol, seen above. This symbol signifies that electric and
electronic equipment and batteries should not be disposed of with other
household waste, but should be disposed of separately.
As the end user it is important that you submit your used batteries to the
appropriate and designated facility. In this manner you make sure that the
batteries are recycled in accordance with legislature and will not harm the
environment.
All cities have established collection points, where electric and electronic
equipment and batteries can either be submitted free of charge at recycling
stations and other collection sites, or be collected from the households.
Additional information is available at the technical department of your city.
Hereby, Inter Sales A/S declares that the radio equipment type LED-3277 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address: www.denver-
electronics.com and then click the search ICON on topline of website. Write
model number: LED-3277. Now enter product page, and red directive is found
under downloads/other downloads.
http://www.denver-electronics.com/denver-cau-438/Operating Frequency Range:
VHF
(50MHz ~ 230 MHz), UHF (474MHz ~ 862 MHz)
Max Output Power: 45W
DENVER ELECTRONICS A/S
Omega 5A, Soeften, DK-8382 Hinnerup, Denmark
www.facebook.com/denverelectronics
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>