PHILIPS VoiceTracer Audio Recorder User Manual

: June 7, 2024
: Philips

Table of Contents

PHILIPS VoiceTracer Audio Recorder
Safety instructions
Cleaning and disinfection
Disposal of your old product
Your VoiceTracer audio recorder
- Product highlights
- Overview of your audio recorder
Get started
Recording
Playback
Settings
Device and data management
Technical data
DOWNLOAD RESOURCES
FAQ’S
VIDEO
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PHILIPS VoiceTracer Audio Recorder

product

PHILIPS VoiceTracer Audio Recorder

Important
Do not make any adjustments and modifications that are not described in this manual. Follow all safety instructions to ensure proper operation of the device. The manufacturer assumes no liability for damages resulting from non- compliance with the safety instructions.

Safety instructions

Protect the device from rain and liquids to prevent damage to the device or a short circuit.
Do not expose the device to excessive heat caused by placing it on a heating device or in direct sunlight.
Protect the cables from damage by being trapped, particularly at the plugs and where cables exit the housing.
Do not perform any maintenance operations that are not described in this user manual. Do not disassemble the device into its component parts to carry out repairs. The device may only be repaired in authorized service centers.
All wireless devices may be susceptible to interference, which could affect performance.
Back up your data and recordings. The manufacturer’s warranty does not cover loss of data resulting from user actions.

Rechargeable built-in battery

This device contains a built-in Li-polymer battery which should not be replaced by the customer. The battery may only be replaced in authorized service centers or by an authorized Philips partner for dictation equipment.
Batteries contain substances that may pollute the environment. Used batteries should be disposed of at an official collection point.

Data reset

Philips VoiceTracer has an internal memory with 8 GB built-in storage. If you want to perform a factory data reset, observe the following cautions:

Back up your data and recordings. Performing a factory data reset will delete all data on your device.
Formatting the memory on a computer may cause incompatibilities with your device. Format the memory only on the device.

Hearing protection

Observe the following guidelines when you use headphones:

Set the volume to a moderate level and don’t use headphones to listen for excessively long periods of time.
Be particularly careful to avoid adjusting the volume to a level that your hearing can’t deal with.
Don’t turn the volume up so high that you can’t hear what is going on around you.
In potentially dangerous situations, be particularly careful or temporarily discontinue use.
Don’t use headphones while you are operating a motorized vehicle, cycling, skateboarding, and so on. You could be a hazard to yourself and other road users, and possibly be breaking the law.

Small children

Your device and its enhancements may contain small parts. Keep them out of the reach of small children.

Legal restrictions on recording

The use of the device’s recording function is subject to the legal restrictions that may apply in your country. You should also respect the privacy and personal rights of third parties if you record talks or lectures.
If you want to record telephone calls, check if this is legal in your country. In certain countries, you may be legally required to inform the person you are conversing with on the telephone that you are recording the conversation.

Cleaning and disinfection

Before cleaning, disconnect all cables from the device.
To clean the device, use a soft dry cloth.
To disinfect the device, use products for disinfection of surfaces in clinical areas and patient care equipment, such as surface disinfectant wipes.
Do not use harsh chemicals or strong detergents.
Avoid getting moisture in openings.
Do not rub or strike the surface with anything hard or sharp as this may scratch or damage the surface permanently

Disposal of your old product

Europe

A crossed-out wheeled bin symbol attached to a product indicates that the product is covered by the European Directive 2011/65/EU. Please get informed about the local separate collection system for electrical and electronic products. Please act according to your local rules and don’t dispose of your old products with your normal household waste. Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health.

United States

Rechargeable Li-ion battery:

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. For recycling information, please contact your local waste management facilities or visit www.recycle.philips.com.
This appliance contains a rechargeable lithium-ion battery which must be disposed of properly.
Contact your local town or city officials for battery disposal information. You can also call 1-800-822-8837 or visit www.call2recycle.org for battery drop-off locations.
For assistance, visit our website www.philips.com/support or call 1-800-243-3050 toll free.

Rechargeable NiMH battery:

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. For recycling information, please contact your local waste management facilities or visit www.recycle.philips.com.
This appliance contains a rechargeable NiMH battery which must be disposed of properly.
Contact your local town or city officials for battery disposal information. You can also call 1-800-822-8837 or visit www.call2recycle.org for battery drop-off locations.
For assistance, visit our website www.philips.com/support or call 1-800-243-3050 toll free.

Canada

Rechargeable Li-ion battery:

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. For recycling information, please contact your local waste management facilities or visit www.recycle.philips.com.
This appliance contains a rechargeable lithium-ion battery which must be disposed of properly.
Contact your local town or city officials for battery disposal information. You can also call 888-224-9764 or visit www.call2recycle.ca for battery drop-off locations.
For assistance, visit our website www.philips.com/ support or call 1-800-243-7884 toll free.

Rechargeable NiMH battery:

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. For recycling information, please contact your local waste management facilities or visit www.recycle.philips.com.
This appliance contains a rechargeable NiMH battery which must be disposed of properly.
Contact your local town or city officials for battery disposal information.
You can also call 888-224-9764 or visit www.call2recycle.ca for battery drop-off locations.
For assistance, visit our website www.philips.com/support or call 1-800-243-7884 toll free

About this user manual
Find a quick overview of your device on the next pages. For detailed description, see the following chapters of this user manual. Read the instructions carefully.

Symbols used
Tip: This symbol identifies information that helps you to use your device more efficiently and simply.
Note : This symbol indicates notices which you should observe when handling or operating the device.
Caution : This symbol warns of damage to the device and possible data loss. Damage can be caused by improper handling.

Your VoiceTracer audio recorder

We are delighted that you have chosen a Philips device. Visit our website for comprehensive support, such as user manuals, software downloads, warranty information and more: www.philips.com/dictation.

Product highlights

Superior recording quality
Audio scenes
Voice-activated recording
MP3 and PCM recording
Large color display
8 GB internal memory
Long-lasting battery

What’s in the box

Overview of your audio recorder

Microphone
Record/Status LED
Display
Left function button
Middle function button
Right function button
Up button
Backward button
Record button
Down button
Forward button
File list/Back button
Play/Stop button
Power/Lock switch
Reset button
Headphones jack
Speaker
USB Type-C port
Eye for wrist strap

Get started

Caution: Before you connect your VoiceTracer, first read the safety instructions (see Safety instructions).

Charging the battery

Charge the built-in battery before you use the device for the first time or if you haven’t used it for an extended time period. If the battery is completely discharged and your device turns off, allow the battery to charge for a while before you turn on the device.

NOTE:

A complete charging cycle takes about 3 hours.
Before you charge the battery via computer, make sure that your computer is turned on.
While the device is connected to a computer, it can’t be operated manually.
When the low battery icon is displayed, charge the device promptly.
If you charge your device via computer instead of using a power supply unit, the charging speed might slow down due to a lower charging current. For fast charging, use a USB power supply unit (not included).

Turn the device on and off

To turn the device on or off:
Slide and hold the Power switch on the right side of the device downwards for three seconds.

Key lock

You can lock your device when it’s active to prevent any unwanted device operations or access.
To lock the device:
• Slide the Power switch on the right side of the device upwards towards the lock symbol. XX
The lock symbol appears on the screen for a moment.
All buttons are locked now.
To unlock the device:
• Slide the Power switch downwards.
The unlock symbol appears on the screen for a moment.

Connect to a computer

You can use your recorder as a USB mass storage to conveniently store, back up and move files. Link the device to a computer with a USB cable. Your recorder will automatically be recognized as a mass storage device. You don’t need to install any software.
For more information on how to connect your device to a computer, see the illustration in Start a new recording.

Caution: Don’t disconnect the USB cable from the device while you are transferring files. This might cause data loss.
Note: While the device is connected to a computer, it can’t be operated manually.

Set the date and time

You can always change the date and time as well as the time format on your device.

In stop mode, press the Right function button to open the settings panel.
Press the Record button to select All settings.
Press the Right function button to enter the Device settings.
Press the Down button to navigate to Date & time and then press the Record button to confirm.
Press the Up/Down buttons to navigate to your desired setting Date, Date format, and Time. Use the Forward and Backward buttons to change your desired setting.
Press the Record button to confirm your settings.
Press the Back button to return to the stop mode screen.

Set the device language

You can always change the language of your device.

In stop mode, press the Right function button to open the settings panel.
Press the Record button to select All settings.
Press the Right function button to enter the Device settings.
Press the Record button to select Language.
Press the Up/Down buttons to navigate to your desired language, and then press the Record button to confirm your selection.
Press the Back button to return to the stop mode screen.

Recording

Note

Be careful not to cover the microphones while recording. This might result in a lower recording quality.
If the recording time of your current recording exceeds the available storage capacity, the recording will stop. In this case, delete files from your device to make more storage available.

Before you start recording:

• Make sure your device has enough battery power left. When your battery is almost discharged, you will see a battery low icon .
XX The device will turn off and your current recording will automatically be saved.
• First select the folder you want your recording to be saved in. For more information, see Start a new recording. You can store 100 files in each of the folders A, B, C, and D.
If one of the folders is full, your subsequent recordings will automatically be stored in the next folder.
• We recommend that you make a test recording in order to find the most suitable presets for your recording and achieve the best recording results.

Start a new recording

In stop mode, press the Left function button to start a new recording.
The new file mode screen is displayed.
Press the Right function button to open the settings panel .

To select a folder for your recording to be saved in.
Press the Up/Down buttons to navigate to Folder and then press the Record button to confirm your selection.
Press the Up/Down buttons to navigate to the folder you want your new recording to be saved in and then press the Record button to confirm your selection..
To return to the stop mode screen, press the Back button.
To adjust the settings for your recording:
Press the Up/Down buttons to navigate to your desired setting and then press the Record button to confirm your selection.
To return to the stop mode screen, press the Back button.

3. Press the Record button to start recording. The recording screen is displayed.
The Record/Status LED flashes red.
4. Press the Record button again to stop recording.
The recording is saved to the preselected folder.

Edit a file

You can edit existing recordings in stop mode by appending or overwriting a recording.
Append: Add additional recording parts at the end of an existing recording.
Overwrite: Overwrite an existing recording part starting from any point within the recording.

To append a recording part:
In stop mode of an existing file, press the Record button.

If the cursor of the audio progress bar is at the end of the recording:
- The recording screen is displayed and a new recording part is added at the end of your file.
If the cursor of the audio progress bar is at the beginning of the recording:
- The editing panel opens.
- Press the Up/Down buttons to select Append and then press the Record button to confirm your selection.
- The recording screen is displayed and a new recording part is added at the end of your file.

To overwrite a recording part:

In playback mode, press the Play/Stop button to stop playback at your desired part.
Press the Record button.
The editing panel opens.
Press the Up/Down buttons to select Overwrite and then press the Record button to confirm your selection.
The recording screen is displayed and a new recording starts from where you stopped playback.

Tip
If you always want to either append or overwrite a recording part and don’t want the editing panel to open each time, press the Right function button to open the settings panel . Press the Down button to navigate to Edit mode and then select Append or Overwrite.

Playback

Note: If you have connected headphones to your Voice Tracer, the built-in speakers are disabled.

Start and stop playback

In stop mode, press the Previous track or Next track button to navigate to your desired recording. To start playback, press the Play/Stop button.
The Record/Play indicator illuminates green. Alternatively, press the File list button and then press the Up/Down buttons to navigate to your desired recording. To start playback, press the Play/Stop button.
To adjust the volume, press the Up/Down buttons.
To stop playback, press the Play/Stop button.
To continue playback, press the Play/Stop button again.

Fast rewind or fast forward
In playback mode or stop mode, press and hold the Backward or Forward button to jump to the desired part of the recording. Release the switch when you have reached your desired playback part.

Note: If you have set bookmarks and press the Backward or Forward button shortly, the audio progress indicator will jump to the next or previous bookmark. If you have not set bookmarks and press the Backward or Forward button shortly, you will jump to the previous or next file.

Play back files from a selected folder

In stop mode, press the File list button.
All voice recordings are displayed.
Press the Left function button to open the folder panel.
Press the Up/Down buttons to navigate to your desired folder and then press the Record button to confirm your selection.
Only the files in the selected folder are displayed now.

Delete files

You can delete individual files from your device.

In stop mode or playback mode, press the Right function button to open the settings panel.
Press the Up/Down buttons to navigate to Delete and then press the Record button to confirm your selection.

Settings

Settings mode

In the settings mode, you can change and adjust various settings according to your own preferences.

Recording settings
Playback settings
Device settings

Start the settings mode

In stop mode, press the Right function button to open the settings panel.
Press the Record button to select All settings.

Navigate between settings
Use the Up/Down buttons.
Select a setting
Press the Record button.

Recording settings

Scene
Select a scene according to specific recording situations, e.g. a lecture or an interview. Every scene has predefined settings, such as the format or the microphone sensitivity, that cannot be changed. If you would like to change the settings of a scene, you need to select the scene Custom where you can define each setting according to your own preferences.

Format
Select the format of your recording according to specific recording situations.

Mic sensitivity
Adjust the microphone sensitivity of your Voice Tracer. Select the sensitivity according to the background noise, number of recorded sound sources and distance between sound source and microphones.

Limiter
Activate this function to prevent recordings from being oversteered by sound input over the maximum sound level. If the recording suddenly exceeds the maximum sound level, the microphone sensitivity is automatically reduced.

Noise cut
Turn the Noise cut feature on in order to reduce background noise while recording. This way, especially audio recordings sound clearer.

Wind filter
Activate the wind filter to reduce wind noise when you are recording in a very windy environment.

Folder
Select the folder you want your recording to be saved in.

Voice activation
Use voice activation to start recording when you begin speaking. When you stop speaking, the device will automatically pause recording after three seconds of silence. It will resume only when you begin speaking again.

Edit mode
Select what should happen when you edit a recording.

Pre-recording
When the pre-recording function is enabled, the device will start recording some seconds prior to the event.

Timer
Use the timer function to automatically start recording on a preset date and at a preset time. You can also select when the recording should stop.

Auto divide
During recording, the auto divide feature will automatically split the current recording and save a new file every 15, 30 or 60 minutes.

Auto bookmark
Use the Auto bookmark funktion to automatically set bookmarks at preset time intervals.

External input
Choose between various input sources to guarantee the best recording quality for specific recording situations.

Playback settings

Play mode
Choose between various playback options.

Equalizer
Choose between the equalizer music options Classical, Jazz, Pop, or Rock.

ClearVoice
Activate the ClearVoice function for better playback quality. Dynamic emphasis on quiet passages improves the intelligibility of quiet voices.

Device settings

Language
Select your desired device language from the language list. You can change the language whenever you want.

Brightness
Adjust the brightness of your screen acccording to your own requirements.

Backlight
To save your Voice Tracer’s battery power, you can reduce the backlight time. If you don’t operate your device for the preset time, the backlight turns off automatically.

Date & time
You can always change the system date and time on your device. Use the Backward, Forward, Up, and Down buttons to set the date and time.

Recording light
If you turn on the recording light, the Record/Status LED will illuminate red when recording.

Auto Off
Select a time for your device to automatically turn off when you don’t operate it.

Device sounds
Select if you want the device sounds, such as key tone and power on/off sound, to be turned on or off.

Select storage
Select if you want your recordings to be saved on the device’s internal storage or on the external memory card.

Format storage
Use this function to format your device’s internal storage or the memory card and delete all data. For more information, see Reset data.

Reset settings
You can reset your menu settings to their default state—the way they were when you first purchased your device and turned it on. For more information, see Reset settings.

Information
See various information about your device, such as the available memory space or the firmware version.

Device and data management

Transfer data to the computer

You can quickly and conveniently move files from your VoiceTracer to your computer. Link the device to a computer with a USB cable. Your recorder will automatically be recognized as a mass storage device. You don’t need to install any software.

For more information on how to connect your device to a computer, see the illustration in Charging the battery.
Caution Don’t disconnect the USB cable from the device while you are transferring files. This might cause data loss.
Note While the device is connected to a computer, it can’t be operated manually.

Transfer data from VoiceTracer to the computer

Connect the device to the computer via the supplied USB cable.
A charging battery icon appears on the screen and the Record/Status LED flashes orange for a few seconds.
Open Windows Explorer on a Windows computer, or open Finder on a Mac computer.
Your VoiceTracer is recognized as an external drive.
Double-click the VoiceTracer drive.
The content of your VoiceTracer is displayed in a new window.
Select the desired files from one of the folders and copy, cut or drag them to the desired location on your computer.

Reset your device and data

Device reset
If you should encounter problems with your device software, for example, the software freezes, the device works slowly or apps don’t respond, you can reset your device and restart it.

Press and hold the reset button on the right side of your device by using a small, pointed object, for example, a paper clip.
To restart the device, slide and hold the Power switch on the right side of the device downwards for three seconds.

Reset data

You can format your device’s internal storage and delete all data from your device.
Caution : Formatting your Voice Tracer will delete all data on your device. Before you perform a data reset, back up any important data saved on your device.
Note: Your menu settings won’t be deleted and are still available after resetting the data.

To reset your data:

In stop mode, press the Right function button to open the settings panel.
Press the Record button to select All settings.
Press the Right function button to enter the Device settings.
Use the Up/Down buttons to navigate to Format storage and then press the Record button to confirm your selection.
Select if you would like to reset the data on the internal storage or on the memory card, and then press the Record button to confirm your selection.
Select Yes.
All data is deleted from the selected storage.

Reset settings

You can reset your menu settings to their default state— the way they were when you first purchased your device and turned it on.
Caution Resetting your menu settings will delete all settings you have made on your device. After a reset, you will have to adjust all settings again.
Note Your data won’t be deleted and is still available after resetting the menu settings.

To reset your settings:

In stop mode, press the Right function button to open the settings panel.
Press the Record button to select All settings.
Press the Right function button to enter the Device settings.
Use the Up/Down buttons to navigate to Reset and then press the Record button to confirm your selection.
Select Yes.
All settings on your device are reset to their default state.

Updating your device

Your device is controlled by an internal program called firmware. As a part of ongoing product maintenance, the firmware is upgraded and errors are corrected.
It is possible that a newer version (an ‘update’) of the firmware has been released since you purchased the device. In this case, you can easily update your device to the latest version.

Caution

Before you update the firmware, make sure that your device has at least 30% battery power left. This helps to prevent the power supply being interrupted during the update.
Do not disconnect your VoiceTracer from the computer during the firmware update. Failures in the firmware update might result in the device’s malfunctioning.

Note To find out about new firmware versions, regularly check the product website for your model at www.dictation.philips.com/voicetracer.

Update your VoiceTracer

Connect the device to the computer via the supplied USB cable.
A charging battery icon appears on the screen and the Record/Status LED flashes orange for a few seconds.
Download the firmware update file for your model from the product website www.voicetracer.com/help.
Open Windows Explorer on a Windows computer, or open Finder on a Mac computer.
Double-click the VoiceTracer drive.
The content of your VoiceTracer is displayed in a new window.
Copy the firmware update file to the root directory of the device.
During this process, the Record/Status LED flashes orange. When the process is complete, the Record/Status LED stops flashing.
Disconnect the device from the computer.
The firmware is automatically updated.
The Firmware update window is displayed.
When the update is complete, the device will automatically switch off.

Technical data

Connectivity

Headphones: stereo jack, 3.5 mm, impedance 16 Ohm or more
USB: type C, high-speed 2.0

Audio recording

Built-in microphone: 2 omni-directional microphones
Recording formats: MPEG1 layer 3 (MP3), PCM (WAV)
Recording quality: MP3 (8, 32, 64, 96, 128, 192,256, 320 kbps), PCM (22 kHz/16 bit, 44.1/16 bit, 48 kHz/16 bit)
Audio scenes: Note, Speech recognition, Interview, Lecture, Meeting, Music, Custom
Recording time (built-in memory): 2147 h (MP3, 8 kbps), 536 h (MP3, 32 kbps), 268 h (MP3, 64 kbps), 178 h (MP3, 96 kbps), 134 h (MP3, 128 kbps), 89 h (MP3, 192 kbps), 67 h (MP3, 256 kbps), 53 h (MP3, 320 kbps), 24 h (PCM, 22 kHz/16 bit), 12 h (PCM, 44.1 kHz/16 bit), 11 h (PCM, 48 kHz/16 bit)
Pre-recording mode: 5, 10, 15 seconds buffer
File editing function: overwrite, append
Auto-divide function: 15, 30, 60 minutes
Auto-bookmark function: 5, 10, 15, 30, 60 minutes
Bookmark function: up to 32 per file
Voice-activated recording: 25 levels
Instant one-touch recording
Record monitor function
Recording timer
Wind filter
Limiter (attack time/decay time): slow (32/128 ms), medium (16/64 ms), fast (8/16 ms)
Noise-cut

Speaker

Speaker output power: 200 mW
Speaker size: 11 × 15 mm

Storage media

Built-in memory capacity: 8 GB
Mass storage class compliant
MicroSD card socket: up to 32 GB

Music playback

Sound enhancement: ClearVoice
Equalizer: Classic, Jazz, Pop, Rock
Playback mode: Repeat file, Repeat all, Random
ID3 tag support
Supported file formats: MP3, WMA

Power

Battery type: built-in rechargeable Li-ion polymer battery
Battery lifetime: up to 36 hours of recording (MP3, 8 kbps)
Battery capacity: 1000 mAh
Rechargeable: yes
Charging time (full charge): 3 hours

Design and finishing
Color(s): black/chrome

Display

Type: LCD color display
Backlight
Diagonal screen size: 2 in/5 cm
Resolution: 240 × 320 pixels

Product dimensions

• 4.7 × 12.8 × 1.6 cm / 1.9 × 5.0 × 0.6 in
• Weight: 79 g/2.7 oz Convenience
• Firmware upgradeable
• Keypad lock
• Multi language: English, French, German, Spanish, Italian, Russian, Polish

System requirements

• Free USB port
• Operating system: Windows 10/8/7, macOS, Linux

Green specifications

• Compliant to 2011/65/EU (RoHS)
• Lead-free soldered product

Operation conditions

• Temperature: 1° – 45° C / 34° – 113° F
• Humidity: 10% – 90%

DOWNLOAD RESOURCES

PHILIPS VoiceTracer Audio Recorder [pdf] User Manual VoiceTracer Audio Recorder, DVT2110, DVT2810
Read more: https://manuals.plus/philips/voicetracer-audio-recorder-manual#ixzz7e28ipbbK

FAQ’S

How does the Philips VoiceTracer work?

The Philips VoiceTracer comes with preset scenes which automatically adjust the recorder’s audio settings depending on what you want to record, whether it is notes, audio for speech recognition, interviews, lectures, music or meetings.

How do I start the voice recorder?

Press the Power button. The device will start.

How do I turn off the voice recorder?

Press and hold the Power button for 2 seconds to turn off the device.

How do I change the recording quality?

Press and hold the Play/Pause button for 3 seconds to change the recording quality. The available recording quality are High, Medium and Low.

How do I change the language?

Press and hold the Play/Pause button for 3 seconds to change the language. The available languages are English, French, Spanish, German, Italian, Dutch, Portuguese and Czech.

How do I delete a recording?

Press and hold the Play/Pause button for 3 seconds to delete a recording. A message will be displayed to confirm that you want to delete this recording. Select Yes or No by pressing OK or Cancel respectively on your device. If you select Yes, this recording will be deleted from your device. If you select No, this recording will not be deleted from your device.

How do I play back a recording?

Press and hold the Play/Pause button for 2 seconds to play back a recording. You can also press Play/Pause while in standby mode to play back a recording. If you have made multiple recordings on your device and you want to choose which one you want to listen to, press OK or Cancel while in standby mode until you reach the recordings screen where you can select which one you want to listen to by pressing OK or Cancel again on your device until it is highlighted in blue (for example if you want to listen to Recording 1 press OK until Recording 1 is highlighted in blue). You can also use Up or Down buttons on your device if they are available on your device (for example if there is no OK or Cancel button on your device). If there is no playback screen available when you press Play/Pause while in standby mode then this means that there are no recordings stored on your device yet or that there is no memory left on your device for storing recordings (for example if all of your memory has been used up by other files such as music files). In this case please make some room on your device by deleting some music files first before making new recordings so that there is enough memory left for storing recordings as well as other types of files such as music files again so that you can play back recordings later on if needed (for example if you need them for some reason such as listening back later on). Please note that it is not possible to delete voice recordings from within this voice recorder app itself but only from within Windows Explorer (for example if using Windows 10) or Finder (for example if using Mac OS X). Please see below how to delete voice recordings from within Windows Explorer or Finder depending on what operating system you are using (for example Windows 10 or Mac OS X).

How do you delete recordings on Philips Voice Tracer?

Slide the record switch to the up position to end the recording slide the record switch down to delete a recording use the left and right navigation buttons to select the file to be deleted.

How do I transfer files from my Philips Voice Tracer?

Connect your player to the computer via the USB port.
Launch Windows Explorer.
Under the player drive select the VOICE folder.
Drag & drop the voice recordings files that you made with your player to the computer.

How do I transfer voice recordings to my computer?

Insert the USB cable into the USB port on the side of the voice recorder.
Connect the opposite end of the USB cable to one of the USB ports on the computer system.
Click “Start” and “Computer” (or “My Computer”), and then double-click the removable device icon.

Where are my saved audios?

Find or delete your audio recordings
On your Android phone or tablet, open your device’s Settings app Google. Manage your Google account.
At the top, tap Data & privacy.
Under “History settings,” tap Web & App Activity. Manage activity. On this page, you can: View a list of your past activity: Items with the audio icon.

Where is the Voice Recorder on my phone?

Swipe down from the top of the phone screen twice to open the Quick Settings menu. You may need to swipe left to locate the Screen Recorder app. Tap on it and then tap Start now. The Screen Recorder menu will come up on the screen with the buttons for Record, Settings, and Close/Stop.

Why my recorder is not working?

Check for updates if you’re running an outdated OS version. Install the latest Phone app version on your device. For more information, see How to Update Android Apps Manually and Automatically. Your Android device and carrier need to support the call recording feature.

How long will a voice memo record?

No, there is no limit in Voice memos app. Just a 1 thing, it indepandeds in how much you have free storage on your device. It records when the screen is locked.

How do you charge a Philips Voice Tracer?

The rechargeable battery Philips Voice Tracer can be charged in the Voice Tracer. When the Voice Tracer is connected to a computer, the rechargeable battery is automatically charged. A complete recharge cycle takes about 2.5 hours.