iNGCO 202404 HS2401_HS2401e HAMMER User Guide
- July 3, 2024
- iNGCO
Table of Contents
- 202404 HS2401_HS2401e HAMMER
- Safety
- The use of the manual
- Important information
- Package content
- Technical Specifications
- Appearance of the phone
- eSIM function
- Buttons
- Turning the phone on and off
- Using the touch screen
- Communication
- Maintenance of the device
- Correct disposal of used equipment
- Correct disposal of used battery
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
QUICK START GUIDE
HAMMER HS2401_HS2401e
Lot number: 202404
202404 HS2401_HS2401e HAMMER
CAUTION! | Statement |
---|
The manufacturer is not responsible for the consequences of situations caused
by improper use of the phone or failure to follow the instructions in the
operating manual.| The software version can be upgraded without earlier
notice.
The manufacturer’s representativereserves the right to decide on the correct
interpretation of this manual.
Safety
—DO NOT RISK—
All wireless devices may cause interferences, which could affect the quality
of other connections. Do not switch the device on in places which are
prohibited from using cell phones, or when it may cause interferences or other
dangers. Always abide by any kinds of prohibitions, regulations and warnings
conveyed by the staff.
—RESTRICTIONS IN USE—
Wi-Fi wireless connectivity uses the 2.4 GHz band and the 5 GHz band. The 5
GHz Wi-Fi band shall not be used outdoors in the European Union. Please
observe the national and local regulations at the place of use.
—QUALIFIED SERVICE— Only qualified personnel or an authorized service
center may install or repair this product. Repairing the device by an
unqualified or unauthorized service technician may result in damage to the
device
and void the warranty.
—ALARM CALLS—
Making alarm calls may not be possible in some areas or circumstances. It is
recommended to find an alternative way to notify emergency services if you are
going to this type of remote areas.
—WI-FI (WLAN)—
In the European Union Member States, a WLAN network may be used indoors
without any restrictions.
—PETROL STATIONS—
Do not use your mobile phone while refuelling at a petrol station or in the
vicinity of chemicals.
CAUTION! In places where there is a risk of explosion (i.e. Petrol
stations, chemical factories etc.), it is advisable to turn off the phone.
Please refer to regulations governing the use of GSM equipment in these
places.
—ROAD SAFETY—
Apart from emergency situations, using the phone while driving should be
carried out only with use of a headset or a speakerphone, which ensures safety
and does not limit motor abilities of the user. If one does not own a headset
and still wants to use the phone, oneshould pull over and stop the car. Pay
attention to the legal regulations of the country you are in, concerning the
use of mobile phone while driving.
—CHILDREN, &PHYSICALLY/MENTALLY DISABLED PEOPLE—
This device should not be operated by people (including children) with limited
physical or mental abilities, as well as by people with no earlier experience
in operation of electronic equipment. They may use the device only under
supervision of people responsible for their safety.
This device is not a toy. Memory card and SIM card are small enough to be
swallowed by a child and cause choking. Keep the device and its accessories
out of reach of children.
—WATER AND OTHER LIQUIDS—
The device has resistance certificate IP69. It means that the device is dust-
proof and waterproof when all of the rubber seals are intact and properly put
in place. As far as possible protect the device from water and other liquids.
Water and other fluids do not have a positive effect on phone electronic
components. If wet, wipe and dry the device assoon as possible.
Make sure the USB cable is dry before connecting it to the phone’s charging
socket. Plugging the cable into a wet or damp outlet exposes it to slow
corrosion and may cause problems with charging your phone.
—BATTERY AND ACCESSORIES—
Avoid exposing the battery to very high/low temperatures (below 0°C / 32°F and
over 40°C / 104°F). Extreme temperatures may influence capacity and battery
life. Avoid contact with liquids and metal objects as it may cause partial or
complete battery damage. The battery should be used according to its purpose.
Do not destroy, impair or throw the battery into flames – it might be
dangerous and may cause fire. Worn-out or impaired battery should be placed in
a dedicated container. Installing an incorrect battery type can cause an
explosion.
Never open the battery. Please dispose of battery according to the
instructions. Disconnect an unused charger from power grid. In case of the
charger wire damage, it should not be repaired but replaced with a new one
cable or a new charger.
Use only original manufacturer’s accessories.
—HEARING—
To avoid hearing damage, do not use the device at high volume levels for a
long period of time, do not put operating device directly to the ear.
—EYESIGHT—
To avoid eyesight damage do not look closely onto the flash light during its
work. A strong bean of light may cause permanent eye damage!
The use of the manual
Pictures of the device and screenshots contained in this user manual may
differ from the actual product. Accessories attached to the smartphone set may
differ from the illustrations included in manual.
Options described in the manual are found in Android system. Those
descriptions may differ, depending on the version of the operating system and
applications installed on the device.
Without prior written consent of the manufacturer, no part of this manual may
be photocopied, reproduced, translated or transmitted in any form or by any
means, electronic or mechanical, including photocopying, recording or storing
in any systems of storing and sharing information.
Important information
The majority of applications which can be installed on the device are mobile apps. Modus operandi of such applications may be different from their counterparts installed on a personal computer. Apps installed on the device may vary depending on country, region, and hardware specifications. The manufacturer is not liable for problems caused by third party software. The manufacturer is not responsible for anomalies that may occur when editing the registry settings and modifying the operating system software. Attempts to modify the operating system can cause malfunctions and problems with applications. It may cause a loss of warranty.
System Android™
This device runs on Android operating system.
Android and Google Play and trademarks of Google LLC.
4.1 Trademarks
- Google, Android, Google Play are Google LLC trademarks.
- Oracle and Java are a registered trademarks of Oracle and / or its affiliates.
- Wi-Fi® Wi-Fi logo are a registered trademarks Wi-Fi Alliance association.
- All other trademarks and copyrights belong to their respective owners.
Manufacturer
mPTech Ltd.
Nowogrodzka 31 street
00-511 Warsaw, Poland
Manufactured in China
Package content
- Mobile phone
- USB cable
- User manual
If any of the above items is missing or damaged, please contact your dealer.
Technical Specifications
Processor: MediaTek Helio G36 Octa-core, 4x 2.2 GHz, 4x 1.6 GHz
Display: 6.56” HD+, 1612 x 720px
Rear camera (main): 13 Mpx + LED
Front camera (selfie): 5 Mpx
RAM memory: 4 GB
Internal memory: 64 GB
Card reader: microSD (up to 256 GB)
Operating system: Android 14
Dual SIM: nanoSIM+nanoSIM+microSD
Dust and water resistance: IP69, STD-MIL-810H
Connector: USB-C
Connectivity: 2.4/5GHz, 802.11 a/b/g/n/ac, GPS/A-GPS, Glonass,
Galileo, Beidou, Bluetooth 5.0
2G: 900/1800 MHz
3G: 900/2100 MHz
4G: 700/800/900/1800/2100/2600 MHz
Sensors: Proximity sensor, Light sensor, Accelerometer, Gyroscope, Compass,
NFC
Battery:
HS2401: Li-Poli 6500 mAh
HS2401e: Li-lon 6500 mAh
Dimensions: 171.5 x 81.2 x 12.39 mm
Weight netto: 270g
Power parameters: fast charging system Pump Express
(5V/7V/9V/12V and maximum 18W)
It is recommended to use the charger: Hammer RAPIDCHARGE
Charger input parameters: AC 100-240V, 50/60Hz 1A
Charger output parameters:
USB-C: 3.3-11V/2.0A, 5V/3.0A,9V/2.22A, 12V/1.67A (20W MAX)
USB-A: 5V/3.0A,9V/2.0A, 12V/1.5A (18W MAX)
USB-C+USB-A: 5V/3.0A (15W MAX)
Appearance of the phone
| Function
---|---
1| Brightness and proximity sensors
2| Internal speaker
3| 5 Mpx digital camera lens (selfie)
4| Notification diode
5| Minijack socket 3.5 mm
6| 13 Mpx digital camera lens (rear)
7| Camera flash / Torch
8| The tray for SIM cards/ microSD
9| Volume control buttons
10| Blockade on/off button
11| Programmable button
12| Touchscreen 6.56”
13| External speaker
14| Multifunctional USB-C port
15| Microphone
16| Lanyard attachment
17| Safety valve (Do not insert anything)
eSIM function
The smartphone is equipped with a tray for SIM / eSIM / microSD cards, thanks to which you can use the phone in the following configurations:
- SIM 1 card + SIM 2 card + microSD card
- eSIM card + SIM 2 card + microSD card
eSIM is only supported by slot 1!
The smartphone supports eSIM technology. To take full advantage of it, you
must additionally purchase a special card with nano eSIM from the
manufacturer’s store. After purchasing the card, the first step is to break
the nano eSIM card from the larger card. Then place it in slot 1 of the tray.
The next step will be to launch and activate the eSIM card.
8.1 Starting and activating the eSIM card
An Internet connection (Wi-Fi or cellular data) is required to install the
eSIM profile). Make sure your smartphone has a nano eSIM card in the
appropriate slot. Go to [Settings] and select [Network and Internet] >
[Mobile Network] > [Add Card] from the menu list (if a regular SIM card is
inserted, go to [eSIM]) to start the card installation. Activating the eSIM
card involves downloading its profile by going through the
configuration.
If the SIM card is in the phone and already has an eSIM profile assigned by
the carrier, the phone will automatically download and install this profile.
**** If adding a new eSIM card, remove the SIM card before configuration!
To set up a new eSIM profile, you will need to enter a special QR code you
receive from your carrier, which you can scan with a QR code scanner or enter
manually by going to the [Need help?] tab while scanning.
After scanning or entering the code, the card’s profile will download
automatically.
Once the profile is downloaded, [Menu] > [Network and Internet] > [Mobile
Network] > [Add Card] will show a tab with the name of the operator and eSIM
signature, and a network coverage icon in the top status bar.
You can also see the process of launching and activating an eSIM card on the
page linked below:
https://www.mptech.eu/promo/jak-dziala-esim
Buttons
Menu (virtual)
Pressing it will cause the list of open apps to appear, where you can switch
in-between or turn them off.
Home (virtual)
One quick press takes you to phone desktop. A longer press launches Google
Assistant.
Back (virtual)
Press to exit the application / return to the previous screen.
Blockade on/off button
- One quick press locks/unlocks the screen.
- Pressing and holding the button for about 2 sec, calls Google voice.
Volume increase and decrease buttons
Pressing during a voice call will cause an increase or decrease of the audio
connection volume.
Programmable button
Pressing on an unlocked smartphone launches a user-defined action or
application. You can change its function using the settings menu.
Turning the phone on and off
To turn on the phone, hold the On/Off/Lock Button until the phone screen
lights up, at which point release the button and wait for the phone to boot
up.
To turn off the phone you need to expand the notification bar, to do this
swipe twice on the screen from top to bottom and press in the lower right
corner, this will open the Disable / Restart Phone or Emergency Calls menu.
Select [Disable] and again to confirm [Disable].
Using the touch screen
The smartphone’s touchscreen makes it easy to select items, perform operations
and gestures. The touchscreen can be controlled by the following actions:
11.1. Touch
Touch one to start options, app, menu. 11.2 Swipe
Quickly swipe up, down, to the left or to the right, to scroll the list or the
screen. 11.3 Triple click
Quickly tap the screen three times to start zooming – if this option is
enabled in your smartphone settings.
11.4 Hold and swipe
Touch an element (an icon perhaps) and hold it for about 1 seconds. Then you
can delete/uninstall that element. 11.5 Slide in and out
Touch the screen with two fingers and slide them together or apart to zoom in
or out a photo or a map.
Communication
12. 1 Making calls
To make a call touch [Phone] icon , placed on the main screen or in Android applications menu and select the keypad icon . Insert the phone number you wish to call. Press “green handset” placed at the bottom of the screen and choose which SIM card you wish to use. It is possible to make a call to an already saved contact. Tap the [Phone] icon , located on the home screen or in the Android application menu, go to the [Contacts] tab and select a contact from the list of saved contacts. To start the call, press .
12. 2 SMS – Messages
You can manage your messages using the [Messages] application in the home
screen or smartphone menu. Start the application and touch the icon , type the
phone number, name of the contact or select a contact from the list. When you
have chosen the contact a screen will appear where you type the message
itself. Type the message body.
Before you send a text message you can transform it into a multimedia message
by pressing symbol ,situated in the left corner of the textbox and adding a
sticker, audio or location. To add a photo from the gallery or directly from
your camera, tap the symbol . To send the message press .
Maintenance of the device
Follow the instructions below.
- For cleaning use only a dry cloth. Never use any agent with a high concentration of acids or alkalis.
- Use the original accessories only. Violation of this rule may result in an invalidation of the warranty.
Correct disposal of used equipment
The device is marked with a crossed-out garbage bin, in accordance with the European Directive 2012/19/EU on used electrical and electronic Equipment (Waste Electrical and Electronic equipment – WEEE). Products marked with this symbol should not be disposed of or dumped with other household waste after a period of use. The user is obliged to get rid of used electrical and electronic equipment by delivering it to designated recycling point in which dangerous waste are being recycled. Collecting this type of waste in designated locations, and the actual process of their recovery contribute to the protection of natural resources. Proper disposal of used electrical and electronic equipment is beneficial to human health and environment. To obtain information on where and how to dispose of used electrical and electronic equipment in an environmentally friendly manner, user should contact their local government office, the waste collection point, or point of sale, where the equipment was purchased.
Correct disposal of used battery
According to the EU directive 2006/66/EC with changes contained in EU directive 2013/56/UE on the disposal of batteries, this product is marked with crossed-out garbage bin symbol. The symbol indicates that the batteries used in this product should not be disposed with regular household waste, but treated according to the legal directives and local regulations. It is not allowed to dispose of batteries and accumulators with unsorted municipal waste. Users of batteries and accumulators must use the available collection points of these items, which allows them to return, recycle and disposal. Within the EU, the collection and recycling of batteries and accumulators is a subject to separate procedures. To learn more about existing procedures of recycling of batteries and accumulators please contact your local office or an institution for waste disposal or landfill.
References
- myphone-mobile.com
- C.P.A. CZECH s.r.o. | Distributor mobilních telefonů a příslušenství
- myphone-mobile.com
- myphone.cz
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>