NEXTECH 0.5W UHFTransceiver User Manual

0.5W UHF Transceiver
DC1102

User Manual

The use of the citizen band radio service is licensed in Australia by ACMA Radio Communications (Citizen Band Radio Stations) Class License and in New Zealand by MED General User Radio License for Citizens Band Radio. Operation is subject to conditions contained in those licenses.

This lightweight hand-held transceiver is suitable for all manner of recreational and professional activities such as building sites, IT cablers, electricians, inter-car road trip communication, or keeping in touch with the kids while they play. Open field transmission range is up to 6km, with typical city range up to 1km. It runs off 3 x AAA batteries and has features you usually only find in more expensive models, including VOX hands-free, monitor, call tones, roger beep, backlit display, headset connection, and CTCSS sub- channels. There is also an LED torch built into the top in case you’re stuck in the dark. Thanks to the auto-battery saving feature, the batteries won’t go flat in case you forget to turn it off.

Specific Recommendations:

• To avoid the risk of burns, do not use the device if the aerial is damaged in any way.
• Do not use the device in a potentially explosive setting (e.g. Around pumps, on the lower deck of a boat, or around a fuel-storage installation or chemical products) If traveling in a car or by bike, stop before using the device.
• Switch off the device if on an airplane or in a hospital,
• Never use the device in close proximity to the radio to avoid interference.
• Remove the batteries if the device is not going to be used for an extended period of time. Never mix used with new batteries.
• Position the transmitter and antenna at least 5cm from your face. Direct the antenna upwards and speak normally.
• Clean the device with a damp cloth. Avoid the use of cleaning agents and solvents.
• Do not modify the device in any way. In the event of damage occurring, ensure that the device is checked by a qualified professional.
  The device cannot be used to contact emergency services.

Key Functions:

Before Using the Device:

Removing the belt clip:
Before insert batteries into the device, first pull the belt clip latch away from the device (See PIC01).

Installing the Batteries:

1. Slide down the battery compartment cover (See PIC02).
2. Insert 3 x AAA Alkaline (Not included)
3. Position the batteries according to the polarity making on the battery compartment.
4. After placing batteries into correct positions, replace the battery cover (See PIC03).

Using the Device:

1. Turning the Device ON/OFF
Switch on the Device: Press and hold the Power Button for 3 seconds then you will hear a beep sound.
Switch off the device: press and hold the Power Button for 3 seconds then you will hear a beep sound.
2. Adjusting the Volume
To increase the volume, press the ▲Up Button; press the ▼Down Button to decrease the volume.
3. Low Battery Indication
The device can detect low battery levels. When the battery voltage is low, the battery icon will flash and a beep will be heard to indicate that the batteries need to be replaced.
4. Receiving/Transmitting Communications:
The device is in “Reception” mode when it is turned ON and not transmitting. When a signal is received on the current channel, the LCD will display receiving icon.
When you press the PTT (push to talk) button, the device switches to “Transmission” mode.
Hold the device in a vertical position with the Mic (microphone) 3-5cm away from your mouth. While holding the PTT button, speak into the microphone in a normal tone of voice. Release the PTT button when you have finished transmitting. For others to receive your transmission, they must be on the same channel as you.
Note:
1. The maximum talking range is up to 6Km, this will depend on your surroundings and environment. It can be affected by obstructions such as hills or buildings.
2. Don’t try to use two devices that are less than 1.5m (5 feet) apart. Otherwise, you may experience interference.

5. Changing Channels:
Press the MENU button once, the channel number will flash on the display.
Press the up▲ /down▼ button to change the channel. Press the PTT button to confirm and return to standby mode.
Note:
If no button is pressed within 15 seconds during the setting, the device will return to standby mode.

6. CTCSS (Continues Tone Coded Squelch System):
Press the MENU button twice, the current CTCSS code will flash on the display. Press the up▲ /down▼ button to change the 38 available codes. Press the PTT button to confirm and return to standby mode. This license-free radio operates on the 476MHZ frequency band; the device has 80 available radio channels. If there are any device users near you, there is a chance that some of the users are operating on the same radio channel. To prevent you from receiving signals from other users, sub-channels have been integrated. When using CTCSS, a low- frequency tone (between 67-250Hz) will be transmitted along with the voice signal. There are 38 available tones to choose from. You are free to choose one of the 38 available sub-channels. Due to filtering, these sub-channels will generally not be audible so they will not disturb the communication.

7. VOX (Hands-free function):
Press the MENU button three times, the current VOX setting will flash on the display and the VOX icon will display, press the UP▲ button to set the VOX sensitivity level between 1 and 3 levels (level 3 is the highly sensitive level). Press the down ▼ button until “OF” appears on the display to turn VOX OFF. Press the PTT button to confirm and return to standby mode. In VOX mode, the radio will transmit a signal when it is activated by your voice or another sound around you. VOX Operation is not recommended if you plan to use your device in a noisy or windy environment.
Note: VOX mode will be overridden when you press the PTT button.

8. Scanning for an active radio channel:
Press and hold the UP ▲ button for 2 seconds: The “SCAN” function indicator will appear on the display and the channel will scan continuously. Once an active channel is found, the scanning will stop and you can listen to the transmission. When the transmission has stopped on that channel, the scan function will resume automatically. Note: If you press the PTT button while listening to a found channel, the device will go back to standby mode on the found channel.

9. Monitor:
Press and hold the DOWN▼ button for about 3 seconds to activate the monitor. Release the DOWN▼ button to return to standby mode.

10. Setting the Call tones:
The device has 10 call tones. Press the MENU button 4 times, “CA” is displayed and on the current call tone. Press the UP▲/Down▼ button to change to another call tone. Press the PTT button to confirm and return to standby mode.

11. Sending a call tone:
Press the call button one time quickly, the call tone will be transmitted on the set channel.

12. Roger Beep On/Off:
After the PTT button is released, the device will send out a roger beep to confirm that you have stopped talking. Press the MENU button 6 times, “RO” will be displayed. Press the UP▲/Down▼ button to set the roger beep ON/OFF. Press The PTT button to confirm your selection and return to standby mode.

13. Backlit Display:
Press any button except for the MENU button to activate the backlight of the LCD display. The backlight will light on approx. 5 seconds.

14. Headset Connection:
The device can be used with an authorized headset. The connector is located on the top of the device. Insert the earpiece plug into the connector (2.5mm jack). There is a small “PTT” button on the earpiece that has the same function as the PTT button on the device. When you use the PTT button from the earpiece, you must also use the microphone from the earpiece to talk.
Note: Do not connect an unauthorized headset, this may damage your device.

15. Battery Saving Function
When the device has not been used for 6 seconds, the economy mode is automatically activated. This does not affect the reception or transmission of the radio. Standby mode is automatically re-activated as soon as a signal is detected.

16. Built-in Flash Light
Your device has a built-in flashlight that can be used for sending light signals or for other lighting needs.

17. Lock & Unlock the Device
Press and hold the MENU button for 3 seconds to lock the device. The button lock icon is displayed on the LCD screen. Press and hold the MENU button for 3 seconds to unlock the device.

18. Technical Specifications

Parks

Channel 11| 476.6750| Simplex      Call Channel
Channel 12| 476.7000| Simplex
Channel 13| 476.7250| Simplex
Channel 14| 476.7500| Simplex
Channel 15| 476.7750| Simplex
Channel 16| 476.8000| Simplex
Channel 17| 476.8250| Simplex
Channel 18| 476.8500| Simplex      Caravan & Campers Convoy Channel
Channel 19| 476.8750| Simplex
Channel 20| 476.9000| Simplex
Channel 21| 476.9250| Simplex
Channel 22| 476.9500| Data Only (No Voice – No Packet)
Channel 23| 476.9750| Data Only (No Voice – No Packet)
Channel 24| 477.0000| Simplex
Channel 25| 477.0250| Simplex
Channel 26| 477.0500| Simplex
Channel 27| 477.0750| Simplex
Channel 28| 477.1000| Simplex
Channel 29| 477.1250| Simplex     Pacific Hwy (NSW) Er Bruce Hwy (Qld)

Road Channel

Channel 30| 477.1500| Simplex     UHF CB Broadcasts
Channel 31| 477.1750| Repeater Input
Channel 32| 477.2000| Repeater Input
Channel 33| 477.2250| Repeater Input
Channel 34| 477.2500| Repeater Input
Channel 35| 477.2750| Repeater Input (Emergency Use Only)
---|---|---
Channel 36| 477.3000| Repeater Input
Channel 37| 477.3250| Repeater Input
Channel 38| 477.3500| Repeater Input
Channel 39| 477.3750| Simplex
Channel 40| 477.4000| Simplex     Highway Channel
Channel 41| 476.4375| Duplex – Repeater Output
Channel 42| 476.4625| Duplex – Repeater Output
Channel 43| 476.4875| Duplex – Repeater Output
Channel 44| 476.5125| Duplex – Repeater Output
Channel 45| 476.5375| Duplex – Repeater Output
Channel 46| 476.5625| Duplex – Repeater Output
Channel 47| 476.5875| Duplex – Repeater Output
Channel 48| 476.6125| Duplex – Repeater Output
Channel 49| 476.6375| Simplex
Channel 50| 476.6625| Simplex
Channel 51| 476.6875| Simplex
Channel 52| 476.7125| Simplex
Channel 53| 476.7375| Simplex
Channel 54| 476.7625| Simplex
Channel 55| 476.7875| Simplex
Channel 56| 476.8125| Simplex
Channel 57| 476.8375| Simplex
Channel 58| 476.8625| Simplex
Channel 59| 476.8875| Simplex
Channel 60| 476.9125| Simplex
Channel 61| | Reserved for Future Expansion
Channel 62| | Reserved for Future Expansion
Channel 63| | Reserved for Future Expansion
Channel 64| 477.0125| Simplex
Channel 65| 477.0375| Simplex
Channel 66| 477.0625| Simplex
Channel 67| 477.0875| Simplex
Channel 68| 477.1125| Simplex
Channel 69| 477.1375| Simplex
Channel 70| 477.1625| Simplex
Channel 71| 477.1875| Repeater Input
---|---|---
Channel 72| 477.2125| Repeater Input
Channel 73| 477.2375| Repeater Input
Channel 74| 477.2625| Repeater Input
Channel 75| 477.2875| Repeater Input
Channel 76| 477.3125| Repeater Input
Channel 77| 477.3375| Repeater Input
Channel 78| 477.3625| Repeater Input
Channel 79| 477.3875| Simplex
Channel 80| 477.4125| Simplex

UHF CB radio – What you need to know

A few things to note about channel allocation. Channels 5 & 35 are reserved for emergency only, and misuse of these channels carries hefty fines or jail time. Besides these, the truckies use channel 40, 18 is the caravan and campers channel. Channels 1-8 and 31-38 are for repeater use, the latest standard states that 41 – 48 and 71 -78 may also become available for repeater operation to supplement the other repeater channels. Presently speech telephony is inhibited on channels 22 and 23 (i.e. data only). Channels 61, 62, and 63  are currently not activated on all UHF units until approved by the ACMA at some time in the future.

Distributed by:
TechBrands by Electus Distribution Pty. Ltd.
320 Victoria Rd, Rydalmere
NSW 2116 Australia
Ph: 1300 738 555
Int’l: +61 2 8832 3200
Fax: 1300 738 500
www.techbrands.com
Made in China

References

• Electus Distribution - Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>