Shuttle SH170R6 Series User Guide

: June 7, 2024
: Shuttle

Table of Contents

Front Panel
Back Pane
Motherboard Illustration
Jumper Settings
Safety Information
Begin Installation
CPU and ICE Installation
Memory Module Installation
- Installing a memory module
Component Installation
Installation of Drives
Installation of Expansion Cards
Complete
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Shuttle SH170R6 Series User Guide

Front Panel

F1	5.25” Bay
F2	3.5” Bay
F3	ODD Eject Button
F4	3.5″ HDD Bay Cover Button
F5	Power On Button
F6	Power LED
F7	HDD LED
F8	USB 3.0 Port
F9	USB 2.0 Port
F10	Mic In
F11	Headphone
F12	USB 2.0 Port & Fast Charger

Back Pane

B1	AC Power Socket
B2	Serial Port (Optional)
B3	DisplayPort
B4	HDMI Port
B5	USB 3.0 Port
B6	eSATA Port
B7	LAN Port
B8	Clear CMOS Button
B9	Front Speaker Out (L/R) Port
B10	Line-In Port
B11	Side Speaker Out (L/R) Port
B12	Real Speaker Out (L/R) Port
B13	Center/Subwoofer Speaker Out Port
B14	Wireless LAN Perforation (Optional)

Motherboard Illustration

Jumper Settings

J1 : Front Audio Header (JP2)

=MIC_L
=GND
=MIC_R
=Front_Detect
=LINE_R
=Mic_detect
=sense
=NULL
=LINE_L
=Line_Detect

J2 USB Header (USB1,USB2)

```
1. =5V_USB
```
=5V_USB
=USB A-
=USB B
=USB A+
=USB B+
=GND
=GND
=NULL
=GND

J3 Fan Connectors (FN1,FN2)

=Ground
=+12V
=SPEED_SENSE
=PWM_CTRL

J4 USB 3.0 Header (JP5)

=5VCC
=A_RX_N
=A_RX_P4
=Ground
=A_TX_N
=A_TX_P
=Ground
=A_Data_N
=A_Data_P
=OC
=B_Data_P
=B_Data_N
=Ground
=B_TX_P
=B_TX_N
=Ground
=B_RX_P
=B_RX_N
=5VCC
=NULL

J5 LPC Header (LPC1)

=+12V
=5V
=5VSB
=SERIRQ
=CLK_24M
=CLK_24M
=SIO_RST
=LFRAME
LAD3
=LAD2
=-12V
=3VSB
=NA
=LDRQ0
=SIO_PME
=LAD1
=LAD0
=+3.3V
=GND
=NULL

J6 COM Header (COM1)

=DCD
=RXD
=TXD
=DTR
=Ground
=DSR
=RTS
=CTS
=NA
=NULL

J7 Power Header (JP4 )

=+HD_LED
=PWR_LED
=-HD_LED
=GND
=RST_SW
=PWR_SW
=GND
=GND
=NA
=NULL

Safety Information

Read the following precautions before setting up a Shuttle XPC.

CAUTION

Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Disposal of used batteries according to the manufacturer’s instructions.
Laser compliance statement
The optical disc drive in this PC is a laser product. The drive’s classification label is located on the drive.

CLASS 1 LASER PRODUCT

CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM.

Begin Installation

For safety reasons, please ensure that the power cord is disconnected before opening the case.

Unscrew 3 thumbscrews of the chassis cover.
Slide the cover backwards and upwards.
Unfasten the rack mount screws and remove the rack

CPU and ICE Installation

Unfasten the ICE fan thumbscrews on the back of the chassis.
Unfasten the four ICE module attachment screws and unplug the fan connector.
Remove the ICE module from the chassis and put it aside.
This 1151-pin socket is easily damaged and pins bend quickly.Always use extreme care when installing a CPU and limit the number of times that you remove or change the CPU. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU.
- Follow the steps below to correctly install the CPU into the motherboard CPU socket.
First unlock and raise the socket lever.
Tear off the protective membrane from the metal load plate. Lift the metal load plate on the CPU socket.

DO NOT touch socket contacts. To protect the CPU socket, always replace the protective socket cover when the CPU is not installed.
Please orientate the CPU correctly and align the CPU notches with the socket alignment keys. Make sure the CPU sits perfectly horizontal, then push it gently into the socket.

**** Please be aware of the CPU orientation, DO NOT force the CPU into the socket to avoid bending of pins and damage of CPU!

Close the metal load plate, lower the CPU socket lever and lock in place.
Spread thermal paste evenly on the CPU surface.

**** Please do not apply excess amount of thermal paste.
Screw the ICE module to the main board. Note to press down on the opposite diagonal corner while tightening each screw.
10. Connect the fan connector
Fasten the Smart Fan to the chassis with the four thumbscrews

Memory Module Installation

Guidelines for Memory Configuration Before installing DIMMs, read and follow these guidelines for memory configuration.

**** Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips are used. (Go to Shuttle’s website for the latest memory support list.) Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.

Dual-Channel mode Population Rule In Dual-Channel mode, the memory modules can transmit and receive data with two data bus lines simultaneously. Enabling Dual-Channel mode can enhance the system performance. The following illustrations explain the population rules for Dual-Channel mode.

Installing a memory module

DDR4 and DDR3/DDR2 DIMMs are not compatible to each other or other DDR DIMMs. Be sure to install DDR4 DIMMs on this motherboard. Follow the steps below to correctly install your memory modules in the memory sockets.

Unlock the DIMM latch.
Align the memory module’s cutout with the DIMM slot notch. Slide the memory module into the DIMM slot.
**** A DDR4 memory module has a cutout, so it only fits in one direction

Check that the latches are closed, and the memory module is firmly installed

Repeat the above steps to install additional memory modules, if required.

Component Installation

As shown, unfasten the screw first
. Install the Mini PCIE card / M.2 SSD into the Mini PCIE slot / M.2 slot and secure with screw.

Installation of Drives

Loosen the purse lock and separate the Serial ATA and power cables.
Place the HDD and optical drive in the rack and secure with
screws from the side.
Connect the Serial ATA Cable to the motherboard.
Place the rack in the chassis and refasten the rack.|
Connect the Serial ATA and power cables to the HDD
Connect the Serial ATA and power cables to the optical drive.

Installation of Expansion Cards

Unfasten the expansion slot bracket screws. Remove the back panel bracket and put it aside.
The maximum size acceptable for display cards is 267mm x 98mm x 34.6mm.
Install the PCIe x4 / PCIe x16 card into the PCIe x4 / PCIe x16 slots.
Secure the bracket.

diagram

Complete

Replace the cover and refasten the thumbscrews.
Complete
Please press the “Del” key while booting to enter BIOS. Here,please load the optimized BIOS settings.