DJI Charging Hub User Guide
- June 7, 2024
- DJi
Table of Contents
WCH2 Charging Hub
Disclaimer
Thank you for purchasing the Charging Hub (hereinafter referred to as–Product”). Read this disclaimer carefully before using this Product. By using this Product, you hereby agree to this disclaimer and signify that you have read it fully. Please use this Product in strict accordance with the document and be sure to pay attention to the Warnings. SZ DJI TECHNOLOGY CO., LTD. And its affiliated companies assume no liability for damage(s) or injuries incurred directly or indirectly from improper use of this Product. Misuse includes, but is not limited to, using unapproved chargers, charging unapproved batteries, short-circuiting, overheating, modifying the Product, or touching the terminals with skin or metal. Refer to the Safety Guidelines and Disclaimer, Intelligent Flight Battery Safety Guidelines, and User Manual for applicable information not herein contained.
DJI” is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as “DJI”) and its affiliated companies. Names of products, brands, etc., appearing in this manual are trademarks or registered trademarks of their respective owner companies. This Product and manual are copyrighted by DJI with all rights reserved. No part of this Product or manual shall be reproduced in any form without the prior written consent or authorization of WI.
This disclaimer is produced in various languages. In the event of divergence among different versions, the Chinese version shall prevail when the Product in question is purchased in China, and the English version shall prevail when the Product in question is purchased in any other region.
Warnings
- The Charging Hub is only compatible with the DJI-specified Charger. DO NOT attempt to use the Charging Hub with any other battery charger.
- The Charging Hub is only compatible with the DJI-specified Intelligent Battery. DO NOT attempt to use the Charging Hub with any other battery.
- Place the Charging Hub on a flat and stable surface when in use. Ensure the device is properly insulated to prevent fire hazards.
- DO NOT touch the metal terminals on the Charging Hub.
- If there is any noticeable buildup, wipe the metal terminals with a clean, dry cloth.
Introduction
The Charging Hub is designed to be used with DJI’s specified Charger. It charges up to two Intelligent Batteries. The Charging Hub will intelligently charge batteries in sequence according to battery power levels from high to low.
Overview
- Power Port
- Charging Port
- Firmware Update Port (Micro USB)
- USB Power Supply Port (5V/2A)
- Status LEDs
- Buzzer Switch
Using the Charging Hub
Use the INSPIRE'” 2 chargers and Intelligent Battery (WB37- 4920mAh-7.6V) for illustration.
Place the battery into the Charging Hub, and connect connector B of the battery charger to the charging hub, then connect the battery charger to a power outlet (100-240V, 50/60Hz). The Charging Hub will intelligently charge batteries in sequence according to battery power levels from high to low. The buzzer will begin beeping when charging is complete. Remove the battery or turn off the Buzzer Switch to stop it. Refer to the “Status LED Description” section for more information about Status LED blinking patterns.
DO NOT charge the Intelligent Flight Battery together with the Intelligent Battery when using the Inspire 2, PHANTOM'” 4 Series Charger or Inspire 2 Car Charger.
USB power supply port can be used to charge the mobile device of 5V/2A.
Status LED Descriptions
Status LED | Description | |
---|---|---|
Blinks Green | Charging | |
Solid Green | Fully charged | |
Blinks Red | Battery Charger Error. Retry with an official battery charger. | |
Solid Red | Battery error | |
Blinks Yellow | Battery temperature too high/ low. The temperature must be |
within operating range (5°-40°C)
| Solid Yellow| Ready to charge
| Alternating Green Blinks| Intelligent Battery not detected
Updating the Firmware
DJI will release firmware updates when available. Refer to the official DJI website and follow the instructions below to update the firmware.
- Download the latest firmware update program from the official DJI website. (http://www.dji.com/crystalsky/info#downloads) )
- Turn on the Charging Hub, then connect it to a computer using a Micro USB cable.
- Run the firmware update program. Press the update button and wait for the process to finish.
- The Charging Hub will automatically restart when the update has been successfully completed.
- Repeat this process if the firmware update fails for any reason.
Specifications
Output Voltage and Current | 8.7V, 6A; 5V, 2A |
---|
Compatible
Battery Charger| Inspire 2 Battery Charger (IN2C180) Inspire 2 Battery Charger
(ADE018) Inspire 2 Car Charger (C6S90-2)
Inspire 1 Battery Charger (A14-100P1A) Inspire 1 Battery Charger (ADE018)
Phantom 4 Series Battery Charger (PH4C100)
Phantom 4 Car Charger (C6S90)
Phantom 3 Professional Battery Charger (ADE019) Phantom 3 Car Charger (C4S90)
Phantom 3 57W Battery Charger (A14-057N1A) Osmo 57W Battery Charger
(A14-057N1A)
Compatible Battery Model| WB37-4920mAh-7.6V
Weight| 138g
Operating Temperature| 41° to 104° F ( 5° to 40°C)
Charging Time (Single)| 71min
The 57 W battery charger does not supply enough power to charge batteries and other devices connected to the USB port simultaneously. DO NOT use the USB port to charge another device when charging batteries.
Compliance Information
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
EU contact address: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
IC Compliance
This device complies with the ICES-003 standards. Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
If you have any questions about this document, please contact DJI by sending a
message to DocSupport@dji.com.
INSPIRE and DJI is trademarks of DJI.
Copyright 2017 DJI All Rights Reserved. EP Ig EP VI
YC.BZ.S01502.03
Printed in China.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>