mira 1.1869.004 Shower Arm and Deluge Head User Guide

mira 1.1869.004 Shower Arm and Deluge Head

Product Information

Specifications :

• Brand: Mira
• Product: Shower Arm and Deluge Head
• Pressure Range: 0.1 – 5.0 bar

Product Usage Instructions

Installation:

1. Ensure installation is done by a competent installer following all relevant regulations.
2. Inspect the fixture for damage before installation.
3. Position the shower fittings at a suitable height and direction for optimal performance.
4. Consider special fixing arrangements for specific wall structures.

Installing the Shower Arm and Deluge Head:

1. Mark backplate fixing holes, avoiding hidden pipes or cables.
2. For solid walls, drill fixing holes and insert wall plugs provided. Use alternative fixings for other wall types.
3. Secure the backplate over the outlet pipe with fixing screws.
4. Fit olive and compression nipple over the outlet pipe and tighten.
5. Attach concealing shroud and compression nut onto the shower arm.
6. Insert the shower arm into the compression nipple and tighten the nut.
7. Tighten the concealing shroud onto the backplate.
8. Screw the deluge head onto the shower arm, ensuring to fit the flow regulator if necessary.
9. Check for leaks after turning on the shower control.

Alternative Installation using Wallplate:

1. Screw the backplate to the wallplate loosely with provided screws.
2. Place the wallplate and backplate assembly over the copper pipe.
3. Mark the position of the wallplate and its fixing holes on the wall.

Frequently Asked Questions (FAQ)

• Q: What is the pressure range for optimal performance of the Mira Shower Arm and Deluge Head?
  A: The shower fittings are designed to give a satisfactory shower over a range of pressures between 0.1 and 5.0 bar.

• Q: Can I install the deluge head to spray towards the opening of the cubicle?
  A: It is recommended to position the deluge head to spray across rather than towards the opening of the cubicle to avoid water splashing out.

MIRA SHOWER ARM AND DELUGE HEAD
INSTALLATION AND USER GUIDE

These instructions must be left with the user.

INTRODUCTION

Thank you for purchasing a quality Mira product. To enjoy the full potential of your new product, please take time to read this guide thoroughly, having done so, keep it handy for future reference. These shower fittings are designed to give a satisfactory shower over a range of pressures between 0.1 and 5.0 bar.

INSTALLATION

General

1. Make sure that the shower fittings are installed by a competent installer.
2. Installations must comply with Water Regulations (Bye-Laws, Scotland), and any other Local Regulations and Building Regulations in force at the time of installation.
3. Before installation carefully inspect the new fixture for any signs of damage.
4. The shower fittings should be positioned at a convenient height for all the family and so that the deluge head will discharge down the centre of a bath or shower cubicle. Position the deluge head to spray across rather than towards the opening of the cubicle (if applicable) and also away from the shower control.
5. Special consideration should be given to the fixing arrangements when installing onto a dry lined, stud partition, shower cubicle or laminated panel wall structures. Installers may wish to obtain alternative proprietary cavity fixings, or choose other options, however, these methods of fixing are beyond the scope of this guide.

Install the Shower Arm and Deluge Head
The shower arm and deluge head must be fitted after the installation of the shower control and the outlet pipe must protrude 18 mm (± 2 mm) from the finished wall surface. The outlet pipe must be fitted at a suitable height and so that the deluge head will discharge down the centre of a bath or shower cubicle.

1. Mark the positions of the backplate fixing holes.
   Caution! Be aware of hidden pipes or cables.

2. For solid walls drill the fixing holes for the backplate with a 6 mm drill and insert the wall plugs (supplied). For other types of wall structure alternative fixings may be required (not supplied).
   Caution! Take care not to drill into hidden pipes or cables.

3. Carefully fit the backplate over the outlet pipe and secure with the fixing screws (supplied).
   Caution! Take care not to damage the ‘O’ Seal in the back of the backplate.

4.  Fit the olive and compression nipple over the outlet pipe and tighten the compression nipple.

5. Fit the concealing shroud onto the shower arm.

6. Fit the compression nut and olive onto the shower arm.

7. Fit the shower arm into the compression nipple and tighten the compression nut.

8. Hand tighten the concealing shroud onto the backplate.

9.  Screw the deluge head onto the shower arm, if necessary fit the flow regulator. Important! Certain mixing valves may have flow regulators, refer to your shower control installation and user guide for  details. Caution! The shower arm is not designed to take weight, therefore care needs to be taken when installing the deluge head.

10. Turn on the shower control and check for leaks.

Alternative Installation procedure using the wallplate

1. Loosely screw the backplate to the wallplate with the two backplate screws provided.
2. Place the wallplate and backplate assembly over the copper pipe.
3. Mark the position of the wallplate and its fixing holes on the wall.
4. Remove the screws and backplate from the wallplate.
5. Drill the two backplate fixing holes, if necessary make a recess approximately 6 mm deep to accept the wallplate. Plug the two fixing holes.
6. Place the wallplate over the copper pipe and fix to the wall with the two wallplate screws.
7. Temporarily fit the two backplate screws to the wallplate. This will prevent the holes from becoming blocked with plaster and grout.
8. Finish the surface of the wall as required ensuring the pipework is protruding by 18 mm ± 2 mm.
9. Remove the two backplate screws.
10. Place the backplate against the finished wall surface and use the two backplate screws supplied to fix the backplate to the wallplate.
11.  Follow steps 4 – 9 from previous section to complete the shower arm installation.

MAINTENANCE

Cleaning

• Warning! Many household cleaners contain abrasive and chemical substances, and should not be used for cleaning plated or plastic fittings.
• These finishes should be cleaned with a mild washing up detergent or soap solution, and then wiped dry using a soft cloth.
• Use your thumb or a soft cloth to wipe any limescale from the soft nozzles and the front surface of the showerhead spray plate.
• Do not use descalents on this product.

SPARE PARTS

• Deluge Head
• 1660.161 – Mira 18.5 cm (Chrome)
• 1799.007 – Mira Beat 20 cm (Chrome
• 1799.008 – Mira Beat 25 cm (White/Chrome)

CUSTOMER SERVICE

Guarantee
Your product has the benefit of our manufacturer’s guarantee which starts from the date of purchase.
To activate this guarantee, please return your completed registration card, visit our website or free phone 0800 0731248 within 30 days of purchase (UK only).
Within the guarantee period we will resolve defects in materials or workmanship, free of charge, by repairing or replacing parts or product as we may choose.
This guarantee is in addition to your statutory rights and is subject to the following conditions:

• The guarantee applies solely to the original installation under normal use and to the original purchaser only. The product must be installed and maintained in accordance with the instructions given in this user guide

• Servicing must only be undertaken by us or our appointed representative.
  Note! if a service visit is required the product must be fully installed and connected to services.

• Repair under this guarantee does not extend the original expiry date. The guarantee on any replacement parts or product ends at the original expiry date.

• For shower fittings or consumable items we reserve the right to supply replacement parts only

The guarantee does not cover:

• Call out charges for non product faults (such as damage or performance issues arising from incorrect installation, improper use, inappropriate cleaning, lack of maintenance, build up of limescale, frost damage, corrosion, system debris or blocked filters) or where no fault has been found with the product. Water or electrical supply, waste and isolation issue
• Compensation for loss of use of the product or consequential loss of any kind.
• Damage or defects caused if the product is repaired or modified by persons not authorised by us or our appointed representative.
• Routine maintenance or replacement parts to comply with the requirements of the TMV 2 or TMV 3 healthcare schemes.
•   Accidental or wilful damage.
• Products purchased ex-showroom display

What to do if something goes wrong
If your product does not work correctly refer to this manual for fault diagnosis and check that it is installed and commissioned in accordance with our instructions. If this does not resolve the issue, contact us for help and advice.
Extended Guarantees
A selection of protection plans are available that enable you to cover repair bills (excludes Eire). Ring 01922 471763 for more details.

•   Helpdesk Service – Ring our Customer Services Team for product advice, to purchase spare parts or accessories or to set up service visit. You can contact us via phone or e-mail, details below. Please provide your model name, power rating (if applicable) and date of purchase.
• Mira Showers Website (www.mirashowers.co.uk)
•  Visit our website to register your guarantee, download user guides, diagnose faults, purchase our full range of accessories and popular spares, or request a service visit.
• Spares and Accessories – We hold the largest stocks of genuine Mira spares and accessories. Contact us for a price or visit our website to purchase items from our accessory range and popular spares.
• Service/Repairs – No one knows our products better than our nationwide team of Service Technicians. We can carry out service or repair work to your product both during and after the guarantee period. Ask about our fixed price service repairs.

To Contact Us : UK

• 0844 571 5000
  Fax: 01 242 282595
  E-mail: Visit www.mirashowers.co.uk/contactus
  Mira Customer Services Dept, Cromwell Road, Cheltenham, Gloucestershire, GL52 5EP

To Contact Us: Eire Only

• 01 531 9337

• E-mail: CustomerServiceEire@mirashowers.com

• Mira is a registered trade mark of Kohler Mira Limited.
  The company reserves the right to alter product specifi cations without notice.

• © Kohler Mira Limited, April 2013

• Check out our full range of Showers

• Electric Showers

• Digital Showers

• Mixer Showers

• Power Showers

• Smart Showers

• Shower Towers

• From Top Shower Brands

• Mira Showers

• Aqualisa Showers

• Triton Showers

• Gainsborough Showers

• Shower Pumps can upgrade your showering experience even more

• Stuart Turner Shower Pumps

• Salamander Shower Pumps

• Grundfos Shower Pumps

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>