DYNOJET PC6-16021 Power Commander 6 Installation Guide
- June 3, 2024
- Dynojet
Table of Contents
DYNOJET PC6-16021 Power Commander 6 Installation Guide
PARTS LIST
- 1 POWER COMMANDER 6
- 1 INSTALLATION GUIDE
- 1 USB CABLE
- 2 DYNOJET DECALS
- 2 POWER COMMANDER DECALS
- 2 VELCRO STRIPS
- 1 ALCOHOL SWAB
- 1 POSI-TAP
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map
(Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can
switch on the fl y between these two base maps when you hook up a switch to
the MAP inputs. You can use any open/close type switch. The polarity of the
wires is not important.
Shifter
(Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires
from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of
the wires is not important. Set to Input 2 by default.
Speed
If your application has a speed sensor then you can tap into the signal side
of the sensor and run a wire into this input. This will allow you to calculate
gear position in the Control Center Software. Once gear position is setup you
can alter your map based on gear position and setup gear dependent kill times
when using a quick shifter.
Analog
This input is for a 0-5v signal such as engine temp, boost, etc. Once this
input is established you can alter your fuel curve based on this input in the
Power Core software.
Launch
You can connect a wire to either Input 1 or Input 2 and then the other end to
a switch. This switch when engaged (continuity) will only allow the RPM to be
raised to a certain limit (set in the software). When released, you will have
full RPM.
WIRE CONNECTIONS
To input wires into the PC6 fi rst remove the rubber plug on the backside of the unit and loosen the screw for the corresponding input. Using a 22-24 gauge wire, strip about 10mm from its end. Push the wire into the hole of the PC6 until it stops and then tighten the screw. Make sure to reinstall the rubber plug.
NOTE: If you tin the wires with solder it will make inserting them easier.
INSTALLING THE POWER COMMANDER 6
-
Remove both seats.
-
Prop the front of the fuel tank up.
-
Lay the PC6 in the tail section and route the cable along the frame.
-
Disconnect the stock connector from the bikes fuel injector, this connector is covered by a rubber boot.
-
Plug the PC6 connectors in-line with the stock wiring harness and the fuel injector.
-
Locate the TPS on the left side of the bike.
-
Using the supplied Posi-tap, attach the unterminated GREY wire of the PCV wiring harness to the stock YELLOW/BLACK wire of the TPS.
It is recommended to use dielectric grease on these connections.
The wire-tap used in this picture is not a Posi-tap. This is an older crimp-on style wire-tap.
-
Remove the battery cover and attach the PC6 ground wire to the negative side of the battery.
-
Using the supplied Velcro, secure the PC6 in the tail section.
Clean both surfaces with the supplied alcohol swab prior to applying the Velcro adhesive. -
Bolt the fuel tank back into place. Reinstall the seats.
Download the latest map fi les from our web site at dynojet.com/tunes.
PUSH THE LIMIT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081
–800-992-4993 –
DYNOJET.COM
© 2008-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
Documents / Resources
|
DYNOJET PC6-16021 Power Commander
6
[pdf] Installation Guide
PC6-16021 Power Commander 6, PC6-16021, 2008-2010 Honda CBR125R, Power
Commander 6, Commander 6
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>