DYNOJET PC6-22059 Power Commander 6 Installation Guide
- June 3, 2024
- Dynojet
Table of Contents
DYNOJET PC6-22059 Power Commander 6 Installation Guide
OPTIONAL ACCESSORY INPUTS
Map: (Input 1 or 2) The PC6 has the ability to hold 2 different base
maps. You can switch on the fly between these two base maps when you hook up a
switch to the MAP inputs. You can use any open/close type switch. The polarity
of the wires is not important.
Shifter: (Input 1 or 2) Used for clutch-less full throttle upshifts.
Insert the wires from the Dynojet quick shifter into either Input 1 or Input
2. The polarity of the wires is not important. Set to Input 2 by default.
Speed: If your application has a speed sensor then you can tap into the
signal side of the sensor and run a wire into this input. This will allow you
to calculate gear position in the Control Center Software. Once gear position
is setup you can alter your map based on gear position and setup gear
dependent kill times when using a quick shifter.
Analog: This input is for a 0-5v signal such as engine temp, boost, etc.
Once this input is established you can alter your fuel curve based on this
input in the Power Core software.
Launch: You can connect a wire to either Input 1 or Input 2 and then the
other end to a switch. This switch when engaged (continuity) will only allow
the RPM to be raised to a certain limit (set in the software). When released,
you will have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 fi rst remove the rubber plug on the backside of the unit and loosen the screw for the corresponding input. Using a 22-24 gauge wire, strip about 10mm from its end. Push the wire into the hole of the PC6 until it stops and then tighten the screw. Make sure to reinstall the rubber plug.
NOTE: If you tin the wires with solder it will make inserting them easier.
INSTALLING THE POWER COMMANDER
-
Remove the rider’s and passenger’s seat (or solo cover).
-
Lift the front of the fuel tank and prop it up with a prop rod.
-
Locate and unplug the stock 6-pin and 4-pin connectors for the bike’s fuel injector sub-harness and throttle position sensor.
These connectors are located behind the throttle bodies under the fuel tank on the left hand side of the bike. -
Plug the pair of 6-pin connectors on the PC6 wiring harness in-line of the stock 6-pin connectors.
-
Plug the pair of 4-pin connectors on the PC6 wiring harness in-line of the stock 4-pin connectors.
-
Route the PC6 wiring harness to the tail section following just inside the left side frame rail.
-
Secure the PC6 ground wire with the ring lug to the negative (-) side of the bike’s battery.
-
Secure the PC6 module inside the tail section, using the supplied Velcro.
Clean the surface with the supplied alcohol swab prior to applying the Velcro. -
Lower and secure the fuel tank.
-
Reinstall the seats.
Download the latest map fi les from our web site at
dynojet.com/tunes.
Optional inputs:
Speed – PINK wire from speed sensor. Connector is located under the fuel
tank on the right hand side.
Connector has PINK, ORANGE/RED, and BLACK/WHITE wires.
Temperature – GREEN/WHITE wire on pin #31 of the ECU.
12v source for Auto tune – BLUE wire of taillight connector. Connector is
located by the ECU. It is a WHITE 3-pin connector with BLACK, BLUE, and YELLOW
wires.
PUSH THE LIMT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081
–800-992-4993 –
DYNOJET.COM
© 2002-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>