DYNOJET PC6-17051 Power Commander 6 Installation Guide
- June 3, 2024
- Dynojet
Table of Contents
DYNOJET PC6-17051 Power Commander 6
PARTS LIST
- 1 POWER COMMANDER 6
- 1 INSTALLATION GUIDE
- 1 USB CABLE
- 2 DYNOJET DECALS
- 2 POWER COMMANDER DECALS
- 2 VELCRO STRIPS
- 1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
Map (Input 1 or 2) The PC6 has the ability to hold 2 different base maps.
You can switch on the fl y between these two base maps when you hook up a
switch to the MAP inputs. You can use any open/close type switch. The polarity
of the wires is not important.
Shifter (Input 1 or 2) Used for clutch-less full throttle upshifts.
Insert the wires from the Dynojet quick shifter into either Input 1 or Input
2. The polarity of the wires is not important. Set to Input 2 by default.
Speed If your application has a speed sensor then you can tap into the
signal side of the sensor and run a wire into this input. This will allow you
to calculate gear position in the Control Center Software. Once gear position
is setup you can alter your map based on gear position and setup gear
dependent kill times when using a quick shifter.
Analog This input is for a 0-5v signal such as engine temp, boost, etc.
Once this input is established you can alter your fuel curve based on this
input in the Power Core software.
Launch You can connect a wire to either Input 1 or Input 2 and then the
other end to a switch. This switch when engaged (continuity) will only allow
the RPM to be raised to a certain limit (set in the software). When released,
you will have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
-
Remove the main seat and the passenger seat.
-
Remove the tail cover by removing the two bolts.
-
Place the PC6 module in the tail section and route the wiring harness on the inside of the tail section towards the front of the bike.
-
Remove the fuel tank.
-
Remove the air box lid by removing the eight screws around the outer edge.
-
Remove the bolts shown. Remove the air box.
-
Locate and unplug the Throttle Position Sensor connector. This is a WHITE 3-pin connector located above the left hand side of the engine.
-
Plug the matching pair of WHITE 3-pin connectors on the PC6 wiring harness in-line of the stock TPS connectors.
-
Locate and unplug the stock sub-harness connector for the bike’s fuel injectors.
This is a BROWN 16-pin connector located on the right hand side of the bike under the fuel tank and behind the engine
-
Plug the pair of 16-pin connectors of the PC6 wiring harness in-line of the stock connectors
-
Secure the ground wire of the PC6 wiring harness with the ring lug to the negative (-) terminal of the bike’s battery.
-
Using the supplied Velcro, secure the PC6 module inside of the tail section. Clean both surfaces with the supplied alcohol swab prior to applying the Velcro adhesive.
-
Reassemble the bike.
Download the latest map files from our web site at dynojet.com/tunes.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>