BLACKVUE CM100GLTE External Connectivity Module User Guide
- June 4, 2024
- BLACKVUE
Table of Contents
BLACKVUE CM100GLTE External Connectivity Module
In the box
Check the box for each of the following items before installing the BlackVue device.
Need help?
Download the manual (including FAQs) and the latest firmware from
www.blackvue.com Or contact a Customer Support expert at
cs@pittasoft.com.
At a glance
The following diagram explains the details of the external connectivity module.
Install and power up
Install the connectivity module at top corner of the windshield. Remove any foreign matter and clean and dry the windshield before installation.
Warning
Do not install the product in a location where it can obstruct the driver’s
field of vision.
- Turn off the engine.
- Unscrew the bolt that locks the SIM slot cover on the connectivity module. Remove the cover, and unmount the SIM slot using the SIM eject tool. Insert the SIM card into the slot.
- Peel off the protective film from the double-sided tape and attach the connectivity module to the top corner of the windshield.
- Connect the front camera (USB port) and the connectivity module cable (USB).
- Use the pry tool to lift the edges of the windshield trim/molding and tuck in the connectivity module cable.
- Turn on the engine. The BlackVue dashcam and connectivity module will power up.
Note
- For full details on installing the dashcam on your vehicle, refer to the “Quick Start Guide” that is included in the BlackVue dashcam package.
- SIM cards must be activated to use LTE service. For details, refer to the SIM Activation Guide.
Product specifications
CM100GLTE
| Model Name | CM100GLTE |
|---|---|
| Color/Size/Weight | Black / Length 90 mm x Width 60 mm x Height 10 mm / |
110g
LTE Module| Quectel EC25
LTE Supported Band
| EC25-A : B2/B4/B12
EC25-J : B1/B3/B8/B18/B19/B26 EC25-E : B1/B3/B5/B7/B8/B20
LTE Features
| Support up to Non-CA CAT. 4 FDD
Support 1.4/3/5/10/15/20MHz RF Bandwidth LTE-FDD : Max 150Mbps(DL) / Max 50Mbps(UL)
LTE Transmit Power| Class 3 : 23dBm +/-2dBm @ LTE-FDD Bands
USIM Interface| Support USIM Nano Card / 3.0V
GNSS Feature
| Gen8C Lite of Qualcomm Protocol : NMEA 0183
Mode : GPS L1, Glonass G1, Galileo E1, Bei-dou B1
Connector Type| Micro USB Type-B Connector with Harness Cable
USB Interface
| Compliant with USB 2.0 specification(Slave Only), Reach up to 480Mbps for
data transfer rate
LTE Antenna Type| Fixed / Intenna (Main, Diversity)
GNSS Antenna Type| Ceramic Patch Antenna
Power Supply
| USB Harness Cable : 3.0m
Typical Supply Voltage : 5.0V / 1A
Supply Input Voltage : 3.3V ~ 5.5V / Max. Current : 2A
Power Consumption
| Idle Mode : 30mA / Traffic Mode : 620mA @ Max. Power (23dBm)
---|---
Temperature Range
| Operation Temperature Range : -35°C ~ +75°C Storage Temperature Range :
-40°C ~ +85°C
Certifications| CE, UKCA, FCC, ISED, RCM, TELEC, KC, WEEE, RoHS
FCC STATEMENT NOTES
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications, However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void your authority to operate the equipment under FCC rules.
Product Warranty
- The term of this product warranty is 1 year from the purchase date. (Accessories such as an External Battery/ microSD Card: 6 Months)
- We, PittaSoft Co., Ltd., provide the product warranty according to the Consumer Dispute Settlement Regulations (drawn up by the Fair Trade Commission). PittaSoft or designated partners will provide the warranty service upon request.
Circumstances
| Warranty
---|---
Within the Term| Outside of the Term
For performance/ functional problems under normal use conditions
| For serious repair required within 10 days of purchase| Exchange/ Refund|
N/A
For serious repair required within 1 month of purchase| Exchange
For serious repair required within 1 month of exchange| Exchange/ Refund
When not exchangeable| Refund
Repair
(If Available)
| For Defect| Free Repair|
Paid Repair/ Paid Product Exchange
Repeated problem with the same defect (up to 3 times)|
Exchange/ Refund
Repeated trouble with different parts (up to 5 times)
Repair
(If Unavailable)
| For the loss of a product while being serviced/repaired| Refund after
depreciation plus an additional 10% (Maximum: purchase price)
When repair is unavailable due to lack of spare parts within the component
holding period
When repair is unavailable even when spare parts are available| Exchange/
Refund after depreciation
- Malfunction due to customer fault
– Malfunction & damage caused by user negligence (fall, shock, damage, unreasonable operation, etc.) or careless use
– Malfunction & damage after being serviced/repaired by an unauthorized third party, and not through Pittasoft’s Authorized Service Center.
– Malfunction & damage due to the use of unauthorized components, consumables, or separately sold parts
- Other Cases
– Malfunction due to natural disasters (fire, flood, earthquake, etc.)
– Expired life span of a consumable part
– Malfunction due to external reasons
|
Paid Repair
|
Paid Repair
This warranty is only valid in the country where you purchased the product.
FCC ID: YCK-CM100GLTE/Contains FCC ID: XMR201605EC25A/Contains IC ID: 10224A-201611EC25A
Declaration of Conformity
Pittasoft declares that this device complies with the essential requirements
and relevant provisions of Directive 2014/53/EU Go to
www.blackvue.com/doc to view the Declaration of
Conformity.
- Product External Connectivity Module
- Model Name CM100GLTE
- Manufacturer Pittasoft Co., Ltd.
- Address 4F ABN Tower, 331, Pangyo-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, Republic of Korea, 13488
- Customer Support cs@pittasoft.com
- Product Warranty One-Year Limited Warranty
facebook.com/BlackVueOfficial. instagram.com/blackvueofficial www.blackvue.com. Made in Korea.
References
- Login • Instagram
- 4K Cloud Dash Cams for Cars and Trucks - BlackVue Dash Cameras
- Declaration Of Conformity - BlackVue Dash Cameras
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>