ETEKCITY EK6020 Digital Kitchen Scale User Manual

ETEKCITY EK6020 Digital Kitchen Scale

Safety Information

IMPORTANT: Please read and comply with all of the instructions and warnings provided in this manual before using the product. Failure to comply with the instructions and warnings provided herein may result in inaccurate results and/or damage to the product itself.

• Always place the scale on a hard, dry and flat surface before measurement in order to ensure accuracy.

• DO NOT exceed the 5000g weight capacity.
  An overload indicator will appear on the LCD display if the limit is exceeded.

• DO NOT immerse the scale in water or corrosive liquids. If a liquid is spilled on the scale platform, immediately wipe the scale clean with a soft cloth in order to avoid potential damage to the scale.

• When replacing batteries, make sure to insert them under the correct polarity as indicated within the battery compartment.

• Replace the batteries if the low-battery indicator is displayed in order to ensure the highest accuracy.

• DO NOT mix new and used batteries to power the device.

• This scale is not intended for commercial or heavy-duty use.

• When not in use, store the scale in a cool, dry environment.

• To clean, wipe the platform surface with a damp soft cloth.

• If the scale fails to turn on, check whether the batteries are installed correctly. Replace the batteries if necessary.

• If the scale is not in use for an extended period of time, take out the batteries to extend the scale service lifetime.

Function Diagram

1. LCD Display
2. Power / Auto-Tare
3. Unit Selection
4. Battery Compartment
5. Anti-Skid Padding

Set-Up

The included AAA batteries are preinstalled in the scale.

1. Open the battery compartment cover located on the backside of the scale.
2. Remove the plastic strip from the battery compartment to allow the batteries to power the device.
3. Reapply the battery compartment cover.

Operation

General Operation

1. Place the scale on a flat and level hard surface for measurement.
2. Press the ON/OFF button to turn on the scale. Wait until the screen displays zero before measuring.
3. Place the object of measurement on the center of the weighing platform.
4. Allow the scale to adjust to the weight of the object for a few seconds before it displays the final measured reading on the LCD screen.

Zero / Tare Function

The tare function allows you to measure objects in a container without having to include the container’s weight in the final measurement.

1. Turn on the scale and wait for the screen to display zero. If the screen does not display zero automatically, press the Z/T button to auto-adjust to zero.
2. Place the desired object which is to be excluded, on the center of the measuring platform.
3. Press the Z/T button to tare the current weight of the object. The screen should now display zero.
4. Place the desired item(s) to be weighed or the center of the measuring platform or within the tared container to calculate the net weight of the desired item(s).

Unit Conversion
To change the unit of measurement, press the UNIT button until the LCD display indicates the desired unit of measurement.

Automatic Power Off
For battery power conservation, the display backlight will automatically power off after 30 seconds of inactivity. Additionally, the scale itself will automatically power off after 2 minute of inactivity.

Manual Power Off
Press and hold the ON/OFF button for 2 seconds to manually turn off the digital scale at any time.

Battery Replacement

1. Open the battery compartment cover on the backside of the scale.
2. Take out the used batteries and dispose them properly.
3. Install new 1.5V AAA batteries, taking note of the correct polarity displayed in the battery compartment.
4. Reseal the battery compartment.

Troubleshooting

Maximum weight capacity: 5000g ( 176 oz).

| Remove the object from the scale to avoid damage.
“Err”| Calibration error.

Unable to measure weight.

| Turn the scale off and turn it back on to retry measurement or auto-tare. Do not move the scale while measuring.
“Lo”| Battery power is low.| Install new batteries.

Specifications

Warranty

Terms & Policy

Etekcity warrants all products to be of the highest quality in material, craftsmanship and service for a minimum of 2 years, effective from the date of purchase. Warranty lengths may vary between product categories.

Should you encounter any issues or have any questions regarding your new product, feel free to contact our helpful Customer Support Team. Your satisfaction is ours!

Etekcity Corporation
1202 N. Miller St. Suite A
Anaheim, CA 92806
USA

Email: support.eu@etekcity.com
Please have your order ID number ready before contacting customer support.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>