DENVER JST-9200 Waterproof IP66 Jump Starter User Manual

Waterproof IP66 Jump Starter
User Manual

Article-No.: JST-9200

Product Overview

Press this button to display the remaining capacity.
Press and hold this button to turn the flashlight on/off.
2| Charging
indicator| Shows the charging progress: 25%, 50%, 75% and 100%.
3| LED Flashlight| Flashlight modes: On, SOS, Flash, and Off.
4| Micro USB input port| Charge the jump starter via a micro USB cable.
5| USB output port| Charge your devices via USB cable.
6| Jumpstart port| Insert plug-in jump start port.
7| Black clamp| Connect the black clamp to the negative terminal of the car battery.
8| Red clamp| Connect the red clamp to the positive terminal of the car battery.
9| Plug| Insert plug-in jump start port.
---|---|---
10| Battery  clamp indicator| Shows the status of the smart battery clamp.
11| Force  start  button| Press this button if the car battery voltage is too low.

Recharging the Jump Starter

1. Connect the jump starter via a micro USB cable to the power source.
2.  Press the ON/OFF button to turn on the product. While charging the jump starter, the battery level indicator flashes. Once it is fully charged, all 4 battery level indicators will light up.
3.  Unplug the cable when no charge is required.

Note:

• When using the product for the first time, make sure that the jump starter is fully charged.
• Use the supplied micro USB cable to charge the product.
• Wall adapter is not included.
  Charging Your Phone or Other Products with the Jump Starter

1.  Connect the jump starter and your phone or other electronic devices via USB cable.
2.  Press the ON/OFF button to turn the product on.
3.  Unplug the cable when no charge is required.

LED Flashlight

Press and hold the ON/OFF button for 3 seconds to switch the flashlight on. Press the ON/OFF button to toggle between On, SOS, Flash and Off modes.
Jump Start Your Car
Note:

• This product is suitable for cars with a 12V electric system (up to 5.0 L petrol or 3.0 L diesel engine) only.
• Check to make sure that 3 to 4 charging indicators are illuminated (battery level is above 50%) before using the device to jump-start your car.
  Step 1: Insert the plug of the smart battery clamp completely into the jump starter. If the green and red lights on the battery clamp are flashing alternately , you are safe to move on to the next step.

Step 2: Connect the red clamp to the positive terminal (+) of the car battery and connect the black clamp to the negative terminal (-) of the

car battery. If the green and red light indicators on the battery clamp are flashing alternately, you are safe to move on to the next step.
However, if the red indicator light is on:

1. The battery clamps may be connected in reverse. If so, you need to disconnect the battery clamps from the vehicle and the jump starter.
2. Adjust the clamps for maximum contact with the battery terminals.

Step 3a: Start your car.

• If you failed to start your car, disconnect the battery clamps from the vehicle and the jump starter. Wait for at least 30 seconds, and then try again.
• If your car failed to start after 3 attempts, use the force start function. See step 3b.

Step 3b (optional): Force start function. First, ensure that the clamps are

connected to the correct battery terminal. Then, press and hold the orce start button for 3 seconds to start your car. When the indicator of the smart clamp lights up green, you need to start the vehicle within the 30s.

Step 4: Once your car is started, remove the battery clamps from the car battery and the jump starter within 30 seconds.

In the following situations, the smart clamp turns protection on.

clamps are reversed.
2.The clamp is short-circuited. – Check whether the two clamps touch each
| or if both clamps touch the same piece of metal.
---|---
The red LED flashes slowly| Reverse charging protection, the voltage of the car battery is higher than 12.6V.
– No jump starter needed, the car battery can start your car.
The red light flashes
quickly| The temperature of the clamp exceeds 65 (+/-5) °C.
– Remove the clamp until the red and green LED flash in turn.
The green LED flashes
slowly| The voltage of the jump starter is too low.
– Try to replace the jump starter or charge it in
time.

Safety Precautions

1.  Use the original smart battery clamps to start the car.
2.  Do not use this unit if any cable, clamp or cord is damaged.
3. Do not connect two clamps together when the product is turned on.
   Do not connect both cable clamps to the same piece of metal.
   Otherwise, the jump starter will be damaged.

Care and Maintenance

1.  Do not use the product to start a bulging car battery.
2.  Store the product in a cool, well-ventilated area.
3.  Handle the product with care and do not abuse it. Avoid dropping or striking the product heavily and repeatedly.
4.  Do not disassemble or modify the product.
5.  DO NOT use detergents to clean the product.
6.  DO NOT place the product for an extended period in a high-temperature environment. The operating temperature of this product is -20 to +60°C. The storage temperature of the product should not exceed 50°C/122°F.
7. Check the battery level of the product at least once every three months and charge the product in time.
8. Keep the product away from children and pets.

Specifications

FAQ

Q: How do I turn off the product?
A: This product will power off automatically when no load is detected or when charging is complete.
Q: How long does it take to fully charge the jump starter?
A: About 7 – 8 hours via the micro USB input port.
Q: How many times can this product start the vehicle with full capacity?
A: About 18 times.
Q: How many times can this product fully charge my cell phone?
A: It depends on the battery capacity of your cell phone. For example, an iPhone 8 can be fully charged 2 times.
Q: What are the safety protections of the smart battery clamp?
A: Short-circuit protection, over-temperature protection, over-voltage protection, over-charge protection, over-discharge protection, over-
current protection and reverse polarity protection.

Package Contents

1 x 9,200mAh Jump Starter
1 x Smart Battery Clamp
1 x Micro USB Cable
1 x User Manual
1 x Color Box

Please notice – All products are subject to change without any notice.
We take reservations for errors and omissions in the manual.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S

http://WWW.denver-eiectronics.com

Electric and electronic equipment and included batteries contain materials, components, and substances that can be hazardous to your
health and the environment, if the waste material (discarded electric and electronic equipment and batteries) is not handled correctly.
Electric and electronic equipment and batteries are marked with the crossed- out trash can symbol, seen above. This symbol signifies that electric and electronic equipment and batteries should not be disposed of with other household waste, but should be disposed of separately. As the end-user, it is important that you submit your used batteries to the appropriate and designated facility. In this manner, you make sure that the batteries are recycled in accordance with the legislature and will not harm the environment.
All cities have established collection points, where electric and electronic equipment and batteries can either be submitted free of charge at recycling stations and other collection sites or be collected from households. Additional information is available at the technical department of your city.
Hereby, Inter Sales A/S declares that the radio equipment type JST-9200 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.denver- electronics.com, and then click the search ICON on the top line of the website. Write model number: JST-9200. Now enter the product page, and the RED directive is found under downloads/other downloads.

Operating Frequency Range: 18-20 times/full charge
Max Output Power: 5V/2A
DENVER ELECTRONICS A/S
Omega 5A, Soften
DK-8382 Hinnerup
Denmark

Warning!
– Lithium battery inside!
– Do not try to open the product!
– Do not expose to heat, water, moisture, or direct sunlight!
– Only charge with the original charger supplied with this product!

References

• Denver A/S

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>