ISANTA SCN49XP Coil Siding Nailer Instruction Manual

SCN49XP

2 1/2” Coil Siding Nailer

Operating Instructions

Senco Brands, Inc.
4270 Ivy Pointe Blvd.
Cincinnati, OH 45245
1-800-543-4596
www.senco.com

  Warnings for the safe use of this tool are included in this manual.

NFD85J • September 3, 2014 (Replaces 11/15/2013)

© 2014 by Senco Brands, Inc.

EMPLOYER’S RESPONSIBILITIES

Employer must enforce compliance with the safety warnings and all other instructions which accompany this tool as shipped from the manufacturer.

Keep this manual available for use by all people assigned to the use of this tool.

For personal safety and proper operation of this tool, read and understand all of these instructions carefully.

2

Tool Use

• Read and understand “SAFETY INSTRUCTIONS” manual shipped with this tool before using tool.

To Adjust Magazine

• Squeeze the gate latch and lift open gate. Open Magazine.

• Lift and shift nail disk to accept different length nails. NOTE: Reference points on magazine coincide with nail lengths.

PLASTIC CARRIER

TYPE -S   (SMALL)

• These tools use either wire collated nails or plastic collated nails.

TYPE -L  (LARGE)

• Plastic collated nails come in two different carrier widths: Type S for the small or narrow strip, and Type L for the large or wider strip.

• The SCN49XP will not accept Type S Carrier Strip.

• Place the nail coil in the magazine.

• Insert first nail into driver track with second nail into the feeder pawl.

• Close magazine cover and gate. Make sure gate is fully latched.

3

• With a “Contact-Actuation” (Dual-Action) trigger, nails can be driven two ways:
a) Position workpiece contact (safety element) against work surface and pull trigger…“Trigger Fire.”
b) Pull trigger and push workpiece contact against work surface for operation each time the workpiece contact is pushed against the work surface. This “bottom-fire” mode of operation is preferred when high speed, rapid fastener placement is desired.

• With a “Sequential” (Restrictive) trigger, nails can only be driven one way. First depress workpiece contact (safety element) against work surface then pull trigger. This feature is helpful when precise fastener placement is required.
• Read the “Customer Satisfaction and Safety Reminder” (CSSR) in the tool and fastener boxes for safety information regarding the Dual Action and Restrictive triggers. Under certain conditions, the Sequential trigger may reduce the possibility of injury to you or to others working with you.

• The deflector can be rotated to change the direction of the exhaust air.

4

• Should a nail jam occur, disconnect air supply.

• Press down on the gate latch and lift open gate.

• Extract bent nail from rear of guide body.

• These tools have an adjustable trigger and can be set for Contact Actuation or Sequential Actuation.

• Press the button on the side of the tool as shown and rotate to the desired setting.

• To adjust the depth of the fastener drive, first disconnect the air supply.

• The Depth of Drive is set by turning the dial under the trigger.

• Turn the dial in the direction shown for the desired setting.

5

Maintenance

• Read and understand “SAFETY INSTRUCTIONS” manual shipped with this tool before using tool.

• All screws should be kept tight. Loose screws result in unsafe operation and parts breakage.

• With tool disconnected, make daily inspection to assure free movement of workpiece contact (safety element) and trigger. Do not use tool if safety element or trigger sticks or binds.

• Squirt Senco pneumatic oil (5 to 10 drops) into the air inlet twice daily. (Depending on frequency of tool use.) Other oils may damage O-rings and other tool parts.

• Wipe tool clean daily and inspect for wear. Use non-flammable cleaning solutions only if necessary
– DO NOT SOAK.
CAUTION: Such solutions may damage O-rings and other tool parts.

6

Troubleshooting

WARNING

Repairs other than those described here should be performed only by trained, qualified personnel. Contact SENCO for information at 1-800-543-4596.

• Read and understand “SAFETY INSTRUCTIONS” manual shipped with this tool before using tool.

SYMPTOM
Air leak near top of tool / Sluggish operation

SOLUTION
Verify air supply / tighten screws.

SYMPTOM
Air leak near bottom of tool / Poor return.

SOLUTION
Clean tool / tighten screws.

SYMPTOM
Poor feed / Tool jamming.

SOLUTION
Clean tool or lubricate magazine.

SYMPTOM
Other problems.

SOLUTION
Contact SENCO.

7

Specifications

8

TECHNICAL SPECIFICATIONS

Accessories

SENCO offers a full line of accessories for your SENCO tools, including:

» Air Compressors
» Hose
» Couplers
» Fittings
» Safety Glasses
» Pressure Gauges
» Lubricants
» Regulators
» Filters

For more information or a complete illustrated catalogue of SENCO accessories, ask your representative for #MK336.

9

Limited Warranty

SENCO® Pneumatic, Duraspin®, Cordless Tools & Compressors

Senco Products, Inc. (“SENCO”) designs and constructs its products using the highest standards of material and workmanship. SENCO warrants to the original retail purchaser that the following products will be free from defects in material or workmanship for the warranty period specified below:

Pnuematic tools
(both Xp and pro)
Five Years

Fusion Tools
Two Years

Combo Kit Tools
One Year

Gas Tools
Two Years

Duraspin Tools
One Year

Air Compressors
One Year

Multi-Blow Hand Nailers & Stapling Hammers
One Year

During the warranty period (which begins on the purchase date), SENCO will repair or replace, at SENCO’s option and expense, any product or part that is defective in materials or workmanship after examination by a SENCO Authorized Warranty Service Center, subject to the exceptions, exclusions and limitations described below. Any replacement product or part will carry a warranty for the balance of the warranty period applicable to the replaced product or part. A DATED SALES RECEIPT OR PROOF OF PURCHASE FROM THE ORIGINAL RETAIL PURCHASER IS REQUIRED TO MAKE A WARRANTY CLAIM. Warranty registration also is required and can be accomplished through on-line Product Registration at www.senco.com or by completing and returning the postage paid warranty registration form included with your Operator’s manual/parts chart information, found inside the product carton. To make a warranty claim, you must return the product, with proper receipt/proof of purchase and return transportation charges prepaid, to a SENCO Authorized Warranty Service Center. A list of SENCO Authorized Warranty Service Centers can be found at www.senco.com or by calling 1-800-543-4596 toll free. SENCO will perform its obligations under this warranty, within a reasonable time after approval of the warranty claim.

Wheelbarrow Compressors:

1. Subject to the exceptions, exclusions and limitations described below, SENCO warrants that the compressor pump will be free from defects in materials and workmanship for two years after the purchase date.
2. Defective parts of the compressor pump not subject to normal wear and tear will be repaired or replaced, at SENCO’s option, during the two year warranty period. If SENCO determines that repair or replacement is not feasible, SENCO will refund the purchase price less reasonable depreciation based on actual use.

SENCO Cordless:

1. Subject to the exceptions, exclusions and limitations described below, SENCO warrants that the SENCO Cordless tool will be free from defects in materials and workmanship for two years after the purchase date.
2. SENCO warrants that the batteries and chargers used with SENCO Cordless tools will be free from defects in material and workmanship for one year after the purchase date.

WARRANTY EXClUSIONS

The following warranty exclusions apply:

1. Normal wear parts are not covered under this warranty. Normal wear parts include, for example, isolators, drive belts, air filters, rubber o-rings, seals, driver blades, piston stops, and piston/driver assembly.
2. This warranty does not cover parts damaged due to normal wear, misapplication, misuse, accidents, operation at other than recommended speeds or voltage (electric units only), improper storage, or damage resulting during shipping.
3. Products used in production/industrial applications as defined by SENCO are excluded from this warranty.
4. Labor charges or loss or damage resulting from improper operation, maintenance or repairs are not covered by this warranty.
5. SENCO does not warrant the Wheelbarrow Compressor Engine/Motor, but the Compressor Engine/Motor may be covered under a warranty offered by its manufacturer.

GENERAL WARRANTY CONDITIONS

This warranty will be honored, only if:

A.  Clean, dry, regulated compressed air has been used, at air pressure not exceeding the maximum indicated on the tool casting;
B.  No evidence of abuse, abnormal conditions, accident, neglect, misuse or improper modifications or storage of the product; and
C.  No Deviation from operating instructions, specifications, and maintenance schedules exists (read Operator Manual for use, specifications, and maintenance instructions).

THIS WARRANTY IS THE ONLY WARRANTY ON THE PRODUCT, AND SENCO DISCLAIMS ALL OTHER WARRANTIES. ANY IMPLIED WARRANTIES WILL BE LIMITED IN DURATION TO THE APPLICABLE WARRANTY PERIOD SPECIFIED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. YOUR REMEDIES ARE SOLELY AND EXCLUSIVELY AS STATED ABOVE. SENCO SHALL IN NO EVENT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, OR SPECIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL SENCO’S LIABILITY EXCEED THE PRICE OF THE PRODUCT WHICH HAS GIVEN RISE TO THE CLAIM OR LIABILITY. ANY LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD SPECIFIED ABOVE. NO EMPLOYEE OR REPRESENTATIVE OF SENCO OR ANY DISTRIBUTOR OR DEALER IS AUTHORIZED TO MAKE ANY CHANGE OR MODIFICATION TO THIS WARRANTY.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

REPLACEMENT OF TOOL DUE TO NATURAL DISASTER

SENCO will replace any tool destroyed by an Act of God such as flood, earthquake, hurricane or other disaster resulting only from the forces of nature. Such a claim will be honored provided that such original retail purchaser had previously submitted a completed warranty registration card for the tool, and then submits proof of ownership and an acceptable statement describing such Act of God documented by an insurance carrier, police department, or other official governmental source. To obtain instructions for filing a claim call 1-800-543-4596.

CUSTOMER SATISFACTION

One hundred percent customer satisfaction is our #1 goal. If for any reason the product does not perform to the original purchaser’s satisfaction, it can be returned to the place of purchase within thirty days with dated sales receipt for a full refund of the purchase price.

© 2013 by SENCO BRANDS, INC.
CINCINNATI, OHIO 45244-1611 USA
www.senco.com
091013

References

• Home - SENCO
• Home - SENCO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>