Laluce Natz Moving Head DJ Lights User Manual
- June 14, 2024
- Laluce Natz
Table of Contents
- Before You Begin
- Unpacking Instructions:
- Caution
- Disclaimer:
- Safety Introductions:
- Introduction:
- Product Overview & Size
- Setup:
- AC Power:
- Mounting:
- Orientation:
- Operation:
- Control Panel Operation:
- System Menu
- DMX Mode 1: 14CH
- DMX Mode 2: 18CH
- IR-C Remote Operation
- TECHNICAL SPECIFICATIONS:
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Laluce Natz Moving Head DJ Lights User Manual
Before You Begin
What In the Box:
1 x Moving Head Lights 1 x Power Cable
- x Bracket
- x Screw
1 x IR Remote Controller 1 x User Manual
Unpacking Instructions:
Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition.
Caution
There are no user serviceable parts inside the fixture. Do not open the housing or attempt any repairs yourself. In the unlikely situation, your unit may require service, please contact us: info@lalucenatzonline.com
Disclaimer:
LaluceNatz believes that the information contained in this manual is accurate in all respects. However, LaluceNatz assumes no responsibility and specifically disclaims anyand all liability to any party for any loss, damage or disruption caused by any errors or omissions in this document, whether such errors or omissions result from negligence, accident or any other cause. LaluceNatz reserves the right to revise the content of this document without any obligation to notify any person or company of such revision, however, LaluceNatz has no obligation to make, and does not commit to make, any such revisions.
Safety Introductions:
Please keep this User Manual for future consultation.
Unpack and check carefully there is no transportation damage before using the
fixture.
Before operating, ensure that the voltage and frequency of power supply match
the power requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid
electric shock.
Disconnect main power before servicing and maintenance.
Use safety chain when fixes this fixture. Don’t handle the fixture by taking
its head only, but always by taking its base.
Maximum ambient temperature is Ta : 104℉/40℃. Don’t operate it where the
temperature is higher than this.
In the event of serious operating problem, stop using the fixture immediately.
Never try to repair the fixture by yourself. Repairs carried out by unskilled
people can lead to damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the same type spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric
shock
To prevent or reduce the risk of electrical shock or fire, do not expose the
fixture to rain or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the LED light beam while the fixture is
on.2.Introduction:
Introduction:
Product Overview & Size
Setup:
AC Power:
The Moving Head DJ Light has an auto-ranging power supply and it can work with an input voltage range of 110 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions.
Mounting:
Before mounting the product, read and follow the safety recommendations indicated in the Safety Introductions.
Orientation:
The Moving Head DJ Light may be mounted in any position; however, make sure adequate ventilation is provided around the product.
Operation:
Control Panel Operation:
To access the control panel functions, use the four buttons located underneath the display.
Button | Function |
---|---|
Select an operation mode or back |
out of the current menu option
a higher value
select a lower value
| Activate a menu option or a selected value
System Menu
Menu | Options | Functions |
---|---|---|
A001 | A001-A512 | DMX Address Setting |
Chnd
| 14CH| 14 Channel Mode
18CH| 18 Channel Mode
Slnd
| nast| Master
d512| Slave
Shnd | Sh 1-4 | Sound Control Mode 1-4 |
---|
Auto
| Aut 1-4| Auto Mode 1-4
Sp 1-9| Auto Speed 1-9
Sens| 0-99| Sound Sensitivity 0-99
Led
| On| LED Display On
Off| LED Display Off
dISP| dISP| LED Display Flip
Pan
| No| X Motor Forward Rotation
Yes| X Motor Reversal
Tilt
| No| Y Motor Forward Rotation
Yes| Y Motor Reversal
Ver| V10| Current Software Version
Rset| Res| Reset
DMX Mode 1: 14CH
CH1 | X-axis Position | 0-255 | 0-100% |
---|---|---|---|
CH2 | Y-axis Position | 0-255 | 0-100% |
CH3 | Motor Speed | 0-255 | 0-100% |
CH4 | Master Dimming | 0-255 | 0-100% |
CH5 | Light Board 1 Red Dimming | 0-255 | 0-100% |
CH6 | Light Board 1 Green Dimming | 0-255 | 0-100% |
CH7 | Light Board 1 Blue Dimming | 0-255 | 0-100% |
CH8 | Light Board 1 White Dimming | 0-255 | 0-100% |
CH9 | Light Board 2 Red Dimming | 0-255 | 0-100% |
CH10 | Light Board 2 Green Dimming | 0-255 | 0-100% |
CH11 | Light Board 2 Blue Dimming | 0-255 | 0-100% |
CH12 | Light Board 2 White Dimming | 0-255 | 0-100% |
CH13
| ****
Strobe
| 0-9| No Function
10-139| Strobe 0-100%
140-255| Random Strobe Speed
CH14
| ****
Master Mode Selection
| 0-9| Manual Dimming
10-199| Auto Mode
200-209| Wait for 2S to reset
210-239| Manual Dimming
240-255| Sound Mode
DMX Mode 2: 18CH
CH1 | X-axis Position | 0-255 | 0-100% |
---|---|---|---|
CH2 | Fine adjustment of X-axis position | 0-255 | 0-100% |
CH3 | Y-axis Position | 0-255 | 0-100% |
CH4 | Fine adjustment of Y-axis position | 0-255 | 0-100% |
CH5 | Motor Speed | 0-255 | 0-100% |
CH6 | Master Dimming | 0-255 | 0-100% |
CH7 | Light Board 1 Red Dimming | 0-255 | 0-100% |
CH8 | Light Board 1 Green Dimming | 0-255 | 0-100% |
CH9 | Light Board 1 Blue Dimming | 0-255 | 0-100% |
CH10 | Light Board 1 White Dimming | 0-255 | 0-100% |
CH11 | Light Board 2 Red Dimming | 0-255 | 0-100% |
CH12 | Light Board 2 Green Dimming | 0-255 | 0-100% |
CH13 | Light Board 2 Blue Dimming | 0-255 | 0-100% |
CH14 | Light Board 2 White Dimming | 0-255 | 0-100% |
CH15 | Color temperature selection / manual dimming |
(channel 16 0-14 valid)
| 0-35| Manual Dimming
36-255| 10 color temperature adjustment
CH16
| ****
Manual dimming / color selection
/ color temperature selection
| ****
0-14
| Manual Dimming or Color Temperature Selection
15-255| Color Selection
CH17
| ****
Strobe
| 0-9| No Function
---|---|---|---
10-139| Strobe 0-100%
140-255| Random Strobe Speed
CH18
| ****
Master Mode Selection
| ****
0-9
| Manual Dimming/Color Selection/Color Temperature Selection
10-199| Auto Mode
200-209| Wait for 2S to reset
210-239
| Manual Dimming/Color Selection/Color Temperature Selection
240-255| Sound Mode
**DMX Connection:**
Set the product in DMX mode / A001 to control with a DMX controller.
Connect the product to a suitable power outlet
Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
IR-C Remote Operation
TECHNICAL SPECIFICATIONS:
Light Source: (LED): 40W Voltage: AC110-240V, 50/60Hz
LED BALL: 1pcs10W 4in1 RGBW leds LED BEAM: 1pcs10W 4in1 RGBW leds
Pan/Tilt movement: X-axis: 540°, Y-axis: 270° LED BALL Angle: 2°
Beam Angle: 4°
Dimmer: 0-100% linear dimming
Operation Modes: Auto, DMX512, Sound, Master/Slave Channel: 14/18CH
Package Size: 8.5×6.1×7.1inch / 21.5×15.6x18cm Weight:1.55 kg / 3.42 lbs