VELOWAVE Electric Bike Instructions

Instructions to Set Up Your VELOWAVE E-bike

Diagram

|
---|---

We know you are excited about getting going but please:
✓ Reseat and charge the battery before the first ride
✓ Make sure the pedals are tight
✓ Make sure the front wheel is installed properly and tight
✓ Check to be sure the tires are inflated properly
✓ Learn how to use the LCD display
✓ Wear a helmet before riding
Please Note: The bike may need further adjustments after assembly
If you have any trouble with setup, please contact us online or through our email address: support@velowavebike.com

Assembling Your E-Bike

1. Read all of the instructions carefully. Be familiar with the proper operation of all items.
2. This quick guide is intended to list the steps needed to assemble your bike with some mechanical skills. It is not a complete manual or training. If you do not feel comfortable or lack some of the skills to assemble it yourself, reach out to a cyclist friend, a local bike mechanic, or one of our support technicians for guidance.
3. Our QA mechanics have assembled and tested your bike beforehand.
4. To assemble your bike, work in a clean area with enough space to maneuver.
5. If installed, remove the battery from the bike to start the assembly.
6. Inspect the bike completely to be sure no damage occurred during shipping.
7. The kickstand is designed to support the bicycle only. Not the rider mounted.
8. You can adjust your saddle position and the tilt on your handlebar items for comfort.
9. Check all screws and parts are tight and properly fixed. We recommend a pre-trip inspection before your first ride.

Installing Your Handlebars

1. Point the headset towards the front of the bike.
2. Place the handlebar in the handlebar mount being careful with the wires.
3. Face the mounting brackets on the front end of the mount with the round edges facing outward.
4. Insert the screws into the screw holes and tighten alternating sides until secure.
5. Verify your front tire lines up with your headset.
6. Check all headset items are tight.

Installing Your Front Wheel – Quick Release Version

1. Insert the front wheel in between the front fork on the bike. Be sure the fork is resting on the outside of the axle.
2. Align the disk between the brake caliper as shown in Figure 2.
3. Insert the skewer into the wheel axle as seen shown. Keep the spring, cam follower, and lever on the LEFT side, nearest the disk brake. Keep the adjustment nut and spring on the RIGHT side. (See Figure 2)
4. Screw the skewer into the end nut until almost tight.
5. Lift the lever up until parallel with the front fork. You should feel the axle tighten into the front forks. Your front wheel is now installed.

|
---|---

Installing Your Front Wheel – Through-Axle Version

1. Insert the axle into the wheel hub as shown. Add the Slim Spacer on the LEFT side (Brake Disk) and the Wide Spacer on the RIGHT side.
2. Insert the front wheel with the spacers in between the front fork on the bike. Be sure to align the the disk between the brake caliper as shown in Figure 2.
3. Now on the outside add the washer and nut on each side and hand turn until snug.
4. Using your wrench, tighten each side alternatively until snug (you might need to secure the opposite nut slightly so the whole axle doesn’t turn).
5. Now tighten each nut putting your weight into the wrench. Your front wheel is now installed.
6. The Adjustment Nut needs to be very tight, be sure to retighten after your first couple of rides.

|
---|---

Brake Caliper and Brake disk on the left side of the bike

Installing Your Pedals

1. Warning: Incorrect installation will cause damage. Please read the instructions and watch our videos if needed.

2. Identify the Left and Right markings on the pedals. They can only be installed on their respective side.
   a. L is for the Left Pedal and it goes on the Left Crank Arm.
   b. R is for the Right pedal and it goes on the Right Crank Arm (Chain Side).

3. Sitting on your bike the pedals go on the Left and Right sides respectively.

4. Keep the pedal Horizontal while hand screwing to get the thread started. Then Use your 15mm wrench to tighten them.

5. Both pedals tighten towards the front of the bike. The left pedal is reversely threaded to allow this.

6. The pedals need to be very tight, be sure to retighten after your first couple of rides. Wrench icon made by Gregor Cresnar from www.flaticon.com

Preparations Before Riding

1. Read all instructions carefully, be familiar with the proper operation of all items. Check for detailed information and guidance on our product page.
2. Warning: Basic electric precautions should always be followed to avoid issues or malfunction.
3. Charge your battery fully in preparation for your first ride.
4. Push the battery pack into the downtube tightly until it gets locked with a clattering sound. Seat your battery securely and remove the key from the lock.
   

How to Use the Display

1. Power on/off
   Press the button to turn on the display. Your bike will be ON. Press again to turn it off. The display will automatically shut down when there is no operation or riding for 5 minutes.

2. Adjust the assist level
   Short press the “+” or “-” button to change the assist level from 0 to 5. 0 is without assist. 5 is the max assist level.

3. Headlight mode
   If your bike is installed with a headlight, press and hold the “+” button for 1 second to switch on or switch off the headlight.

4. Walking mode
   Press and hold the “-” button for 2 seconds to shift into the walking mode, the display indicates P; release the button to exit the walking mode.

5. Information menu
   Press the,   button for 1 second to shift into the information menu, it will show TRIP, ODO, and TIME.

6. Parameter setting menu
   With the display powered on, if you quickly press the   button twice, it will shift into the parameter setting menu. Users are NOT supposed to change the factory default settings. You may exit by quickly pressing the   button twice again or leave it without operation for 30 seconds.

How to Charge Your Bike

There are two ways to charge your battery.

1. Charge the battery ON the bike

1. Find the Charge Port at the bottom of the downtube.
2. Pull out the cover to show the charge port and insert the charger output plug into the port. Connect the input plug to the power supply.

2. Charge the battery OFF the bike

1. Take off the battery from your bike.
2. Place the battery in a clean and flat place at room temperature.
3. Insert the charger output plug into the charge port. Connect the input plug to the power supply.
4. There is a capacity indicator at the top of the battery. Press the button beside to check the charge status. Green means sufficient charge. Yellow means less than 30%. Red means less than10%.

Notes of Charging:

1. Charging time varies from 8 to 10 hours.
2.  The small LED light on the charger in RED indicates it is in charge; The small LED light on the charger in GREEN indicates it is fully charged.
3. Insufficient charging will not influence the battery lifecycle. AVOIDING deep discharge is helpful to protect the battery and extend its lifecycle.
4. If the battery will not be used for a long period, take it off from the bike and discharge its capacity to 60%-80% for the stock. Disconnect it from the charger and place it in a dry, ventilated place without direct sunlight. In order to maintain a long lifecycle, it is recommended to charge the battery every two months.
5. Pay attention to check whether the surface temperature of the battery case rises too high during charging. It is FORBIDDEN to cover the battery during charging.
6. Due to the high temperature in the summertime, it is NOT advisable to charge it immediately after riding. In winter, it is FORBIDDEN to charge the battery in an environment below 0℃. You are recommended to charge it at room temperature.

How to Take Off Your Battery

1. Stand on the left side of the bike.
2. Insert the key into the switch and turn in a counterclockwise direction.
3. Keep your left hand holding the battery. Use your right hand to turn the lock switch under the downtube counterclockwise and the battery will drop off. When the lock is released, hold the battery with both hands and take it off the bike.
   *The battery is heavy. Please hold it tight with both hands in case it drops down.

References

• Vector Icons and Stickers - PNG, SVG, EPS, PSD and CSS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>