TOOLSTATION wessex 20L Wet and Dry Vacuum Cleaner Instruction Manual
- October 27, 2023
- TOOLSTATION
Table of Contents
- TOOLSTATION wessex 20L Wet and Dry Vacuum Cleaner Instruction Manual
- WHAT’S IN THE BOX
- SPECIFICATION
- EXPLANATIONS AND SYMBOLS, CAUTIONS AND WARNINGS
- IMPORTANT SAFETY WARNINGS
- Save all warnings and instructions for future reference.
- Service
- PRODUCT DESCRIPTION AND IDENTIFICATIONS
- ASSEMBLY AND OPERATING INSTRUCTIONS
- Assembly instructions
- Dry vacuum operation
- Wet vacuum operation
- Cartridge Filter – For dry applications
- IMPORTANT
- BLOWING OPERATION
- VACUUM AND BLOW AIR FLOW ADJUSTMENT
- CARE AND CLEANING
- IMPORTANT:
- TROUBLE SHOOTING
- Product Code: 34501/ZD110P-20L-1300W
- ENVIRONMENTAL INFORMATION
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
TOOLSTATION wessex 20L Wet and Dry Vacuum Cleaner Instruction Manual
WHAT’S IN THE BOX
SPECIFICATION
- 1300W
- 230V~,50Hz
- Max Vacuum Pressure : 18kPa Max Air
- Flow : 32L/sec Stainless steel tank
- Blower Function
- 5m power cable
Technical Data
Model| ZD110P-20L-1300W
Input voltage rating| 220-240 V ~ 50 Hz
Input power| 1300 W
Max. vacuum pressure| 18 kPa
Max. air flow| 32 L/sec
Container volume| 20 L
Dry vacuum volume| 13 L
Wet vacuum volume| 11 L
Protection class| II /
Weight(approx.)| 6.3 kg
Protection degree| IPX4
Cable| H05VV-F, 2×0.75mm² , 5m, BS plug
EXPLANATIONS AND SYMBOLS, CAUTIONS AND WARNINGS
IMPORTANT SAFETY WARNINGS
WARNING! Read all safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term ‘power tool’ in the warnings refers to your mains- operated (corded)
power tool or battery operated (cordless) power tool.
This appliance can be used by children aged 8 years and above and persons with
reduced physical, sensory, or mental capabilities, or lack of experience and
knowledge, if they have been given supervision
or instruction concerning the use of the appliance in a safe way and
understand the hazards involved.
Children must not play with the appliance. Cleaning and maintenance must not
be undertaken by children without supervision.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
- IMPORTANT: Read the operating instructions before assembling and using for the first
- Check that the mains voltage is the same as the mains voltage specified on the rating
- Pull out the power plug in the following circumstances: Whenever the appliance is not in use, before opening the appliance, and before all cleaning and maintenance
- Never clean the appliance with
- Never pull the plug out of the socket by pulling the
- Never leave the appliance unattended when ready for
- Keep away from children and
- Take care to ensure that the power cable does not get damaged by being run over, crushed, pulled or similar.
- Do not use the appliance if the power cable is in less than perfect condition.
- If the power cable has to be replaced, the replacement must comply with the design specifications of the
- Never vacuum the following: Burning matches, smoldering ash and cigarette butts, combustible, caustic, flammable or explosive substances, vapour or
- This appliance is not suitable for vacuuming dust which can be harmful to your
- Store the appliance in a dry indoor
- Never use the appliance if it is
- Have the appliance serviced only by an authorisation after- sales service outlet.
- Use the appliance only to carry out work for which it has been designed.
- Take extra care when cleaning
- Use only genuine accessories and spare
- Keep children and other persons away from the electric tool while it is being used. Allowing yourself to get distracted can cause you to lose control of the
Service
Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
PRODUCT DESCRIPTION AND IDENTIFICATIONS
- Air flow adjustment
- Hose
- Duel action floor brush
- Carry handle
- On/Off switch
- Latch
- Caster
- Extension tube
Not all the accessories illustrated or described are included in standard delivery.
ASSEMBLY AND OPERATING INSTRUCTIONS
Intended Use: The wet and dry vacuum cleaner is designed for wet and dry
vacuuming using the appropriate filter. The appliance is not suitable for the
vacuuming of combustible, explosive or harmful substances.
The machine is to be used only for its prescribed purpose. Any other use is
deemed to be a case of misuse. The user / operator and not the manufacturer
will be liable for any damage or injuries of any kind caused as a result of
misuse. Please note that our equipment has not been designed for use in
commercial, trade or industrial applications. Our warranty will be voided if
the machine is used in commercial, trade or industrial businesses or for
equivalent purposes.
WARNING! To prevent serious injury from accidental operation, turn the
vacuum power switch off and unplug the appliance from its electrical outlet
before performing any procedure in this section.
Before you connect the vacuum to a mains supply, make sure that the data on
the rating/technical label is identical to the mains data.
Assembly instructions
-
Unclamp latches.
-
Lift the power head off the container.
-
Remove all the contents from inside the container. Warning: Not all contents are listed in the diagram.
-
Insert the casters into their sockets on the underside of the container and apply pressure until the casters snap into place.
-
Attach filter (not required for blowing), see dry or wet operation for correct use of filter.
-
Place the power head back onto the container, secure into place by clamping shut the latches.
-
Insert the locking end of the hose (marked with an arrow) into the relevant port of the vacuum and turn to lock into place.
-
The extension tubes need to be assembled
-
Attachments can be pushed onto the tubes when required.
-
Connect the extension tubes with hose
Dry vacuum operation
-
Ensure that the power cord is disconnected from the power outlet.
-
Remove the power head from the container as shown in the assembly instructions.
-
Fit the HEPA to the underside of the power head. Unlock the latch and pull out machine head. Check cartridge filter assembly on page 15
-
Firmly assemble the dust bag when you hear a click which is completely cover the sucking hole. Warning! Assemble the dust bag incorrectly may causes dust leaking.
-
Place the machine head back onto the vacuum body and lock the latch correctly.
-
Connect the power cord to a suitable power outlet.
-
Switch on the vacuum and proceed to clean. (I=ON)
-
Switch off the vacuum before emptying. (O=OFF)
-
When emptying the container take care as this may be heavier than anticipated.
-
Clean filters and change if necessary.
Wet vacuum operation
-
Ensure that the power cord is disconnected from the power outlet.
-
Unlock the latches
-
Take out of the machine head
-
Fit the foam filter to the underside of the power head; take care not to damage the filter.
-
Place the machine head back onto the vacuum body and lock the latch correctly.
-
The extension tubes need to be assembled
-
Switch on the vacuum and proceed to clean. (I=ON)
-
Switch off the vacuum before emptying. (O=OFF)
-
When emptying the container take care as this may be heavier than anticipated.
-
Clean filters and change if necessary.
Cartridge Filter – For dry applications
Use the cartridge filter in position over the lid cage for most general dry material pick up.
- With the tank cover in an upside down position, slide the cartridge filter down over the lid cage, pushing until the filter seals against the cover.
- Place filter locking nut into the top of the cartridge filter, hold the tank cover with one hand, turn the handle on the filter retainer clockwise to tighten, locking the filter into place.
- To remove the filter for cleaning, again hold the tank cover and turn the filter locking\ nut counter- clockwise to loosen and remove, slide the cartridge filter off the lid cage.
- To clean the cartridge filter shake or brush off excess dirt or rinse (from the inside of the filter) with water, dry completely (approximately 24 hours) and reinstall. NOTE: If the filter has been used for wet pick up, it must be cleaned and dried before using for dry pick up.
IMPORTANT
**** When vacuuming large volumes of liquid, do not immerse the nozzle completely in the liquid; leave a gap at the tip of the nozzle opening to allow for air inflow. The machine is fitted with a float valve that stops the suction when the container reaches its maximum capacity an increase in motor speed will be heard. When this happens, turn off the machine, disconnect from power supply and empty the liquid into a suitable receptacle or drain. To continue vacuuming, refit the power head to the container. After wet vacuuming, turn the machine off and remove plug from power supply. To prevent the machine becoming moldy, empty the container, clean and dry the inside and outside of the container and remove the foam filter and allow to air dry before storage.
The float valve is a safety feature. Do not attempt to remove or modify this in any way. If the cleaner should overturn during wet operation, switch off immediately and return it to an upright position. Wait for the valve to reset before commencing cleaning.
BLOWING OPERATION
IMPORTANT!
Before commencing please ensure you have read and understood all the safety instructions.
-
Ensure that the power cord is disconnected from the power No filter is required for blowing operations. Ensure that the container is completely empty before commencing.
-
Remove the hose from the vacuum port and insert firmly into the air
-
Select the most appropriate attachment for the job.
-
Connect the power cord to a suitable power outlet
-
Before switching on, make sure you have a firm hold of the hose end.
-
Switch on the vacuum and proceed to clean. (I=ON)
-
If blowing dusty environments, always wear a suitable dust mask.
-
Protect eyes with suitable safety goggles and ensure no one else is nearby when operating.
VACUUM AND BLOW AIR FLOW ADJUSTMENT
The air flow can be controlled by setting the min / max adjustment switch to the desired speed.
CARE AND CLEANING
IMPORTANT:
Make sure that the tool has been thoroughly cleaned before storing it in a
clean, dry and safe place, out of the reach of children.
Remove the plug from the power outlet before commencing any maintenance.
After wet vacuuming, always empty, rinse and dry the container, hose and
attachments. If vacuuming sticky spills, clean the tank and attachments with
warm soapy water.
The foam filter can be cleaned using soapy water. Rinse and air dry for at
least 24 hours. Take care when cleaning as small wood, metal or glass
particles could get trapped in this filter. Check airways on hose and
attachments to ensure there are no blockages.
Never use chemical cleaners or an abrasive cloth to clean the vacuum, use a
mild detergent and warm water. Dry with a soft dry cloth.
Do not oil the motor. Store in a dry place.
Serviceable parts can be bought instore or online from Toolstation:
www.toolstation.com
SKU:51193 Wessex 20L Wet & Dry Vacuum Cleaner Dust bag 3 PACK SKU:88733 Wessex 20L Wet & Dry Vacuum Cleaner Cartridge filter (HEPA)
TROUBLE SHOOTING
Use this section to help you to try and solve any problems you may have:
PROBLEM | POSSIBLE CAUSES | REMIDIES |
---|---|---|
Product does not start | Not connected to power supply | Connect to power supply |
Power cord or plug is defective | Check by a specialist electrician |
Other electrical defect to the
product
| Check by a specialist electrician
Product does not reach full power| Extension cord not suitable for
operation with this product
| Use a proper extension cord
Power source (e. g.
generator) has too low voltage
| Connect to another power
source
Air vents / air inlet / air
outlet are blocked
| Clean the air vents / air inlet / air
outlet
Activated safety valve /
too much water in the tank
| Drain excess of water from the
tank
The vacuum will stop picking up dust/water.| Activated safety valve / too much water in the tank| Let the product cool down and then drain excess of water from
the tank
Unsatisfactory result| Attachment not suitable
for working surface
| Use proper attachment
Dust bag is full| Replace with a new dust bag
Dust bag is damaged| Replace with a new dust bag
Dust filter damaged| Replace with a new dust filter
Attachment / extension tube(s) /
hose not well connceted.
| Check and reconnect the
involved part(s)
Attachment / extension tube(s) /
hose / handle / air inlet blocked
| Remove the blockage(s)
Attachment / extension tube(s) /
hose / handle / air inlet defective
| Replace involved part with a
new one
PROBLEM | POSSIBLE CAUSES | REMIDIES |
---|---|---|
Dust not being retained in the vacuum (dry vacuuming configuration) | Worn dust | |
bag / dust filter | Replace with a new suitable part |
Dust bag / dust filter not
properly attached
| Check and re-attach properly
Defective attachment / extension tube / hose / handle /
air inlet
| Replace involved part with a new suitable one
Excessive vibration or noise| Attachment / extension tube(s) /
hose not properly connected
| Check and re-connect
Loose screws/bolts/nuts on
handle or caster
| Tighten screws/bolts/ nuts
NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR APPLIANCE, PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE APPLIANCE YOURSELF. DOING SO MAY VOID THE WARRANTY AND COULD CAUSE DAMAGE OR PERSONAL INJURY. IF THE PROBLEM STILL PERSISTS, PLEASE CONTACT US BY REFERRING TO THE SERVICE & SUPPORT INFORMATION ON THE FOLLOWING PAGE.
DECLARATION OF CONFORMITY / PERFORMANCE
Product Code: 34501/ZD110P-20L-1300W
Product Description : Wessex 20L Wet & Dry Vacuum Cleaner
- Toolstation Limited, Express Park, Bristol Road, Bridgwater, Somerset TA6 4RN This declaration of conformity is issued under the sole responsibility of Toolstation
- Object of the declaration
The object of the declaration described above is in conformity with the relevant Community harmonization legislation:
- Electromagnetic Compatibility Regulations 2016 2014/30/EU
- Electrical Equipment (Safety) Regulations 2016 2014/35/EU
- The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 2011/65/EU&(EU)2015/863
- References to the relevant standards used (or references to the specifications in relation to which conformity is declared:
BS EN 60335-1
BS EN 60335-2-2
BS EN 62233
BS EN 55014-1
BS EN 55014-2
BS EN 61000-3-3
BS EN 61000-3-2
BS EN 62321
- Additional information:
Signed for and on behalf of Toolstation Limited
ENVIRONMENTAL INFORMATION
The symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for recycling, please contact your local authority, or where you purchased your product.
Read More About This Manual & Download PDF:
References
- Home - warranty repair spares | Coreservice
- Toolstation | Low prices on 25,000+ trade quality products
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>