MI JMJQR03IQI Robot Builder Rover User Manual

Mi Robot Builder Rover
User Manual

Specifications

Name: Mi Robot Builder Rover
Model: JMJQR03IQI
Materials: ABS, PC
Number of pieces: 978
Weight: 2500 g
Dimensions: 380x320x95 mm
Age: 10 years+
Input voltage: 14 V
Input: 1.0 A
Battery: Li-polymer| Battery capacity: 18.3 Wh
Intelligent brick: Bluetooth
Wireless connectivity: Bluetooth 4.0
BLE operating frequency: 2402 MHz-2483 MHz
Transmit power: 0 dBm
2.4G Radiofrequency: 2402 MHz-2483 MHz
Transmit power: 0 dBm
Storage temperature: -10°C~45°C
Operating temperature: 0°C~55°C
---|---

Product Overview

1. Intelligent Brick
   1.Microphone
   2.Indicator
   3.Power Button
   4.Speaker
   5.Motor Ports
   6.Expansion Ports
   7.Pin Holes
   8.Reset Hole

2. Adapter
   Use only the provided power adapter.
   Ports А, В, C, D can be used for charging
   Adapter Model: AD10002
   Input: 100 – 240 V ~ 50 / 60 Hz 0.5 A MAX
   Output: 14V 1 A / 5V 1 A
   Charging: Indicator light is red.
   Fully charged: Indicator light is off.
   The light is green when turning on the intelligent brick.

3. Motor

Assembling Mi Robot Builder Rover

1. Before you start
   Put small bricks in the storage box, and large bricks in the bag.

2. Build your robot
   Follow the building instruction or download the e-version from the Help in the Mi Robot
   Builder app to assemble the bricks.

3. Inspect your robot
   Make sure the controller is fully charged when the robot is on its first use.
   Make sure the motors are tightly connected with blocks.
   Make sure you followed the building instruction when you were assembling your robot.

Turning on/off

Turning on: press the power button
Turning off: press and hold the power button for 3 seconds until you hear a sound prompt

Installing the app

1. Download the app
   Scan the QR code below or go to the App Store to download and install “Mi Robot Builder”.
   
   http://en.iqi-inc.com/download

2. Connecting your robot
   Make sure your phone’s Bluetooth is turned on. Open the Mi Robot Builder app and tap the Bluetooth icon in the upper left corner to connect your robot.
   

3. Firmware updates and support
   Make sure your phone is connected to the internet (preferably via Wi-Fi).
   Open the app and connect your the robot, and then go to Settings > System updates >
   Firmware updates.
   It takes about 20 minutes to update the firmware.
   Please note the following:
   • Make sure the motor is off during the updates. Otherwise, the parameters may be reset and which may result in malfunction.
   • Make sure the controller is fully charged before the update.
   • Keep your phone away from the controller during the update.
   • Refer to the “Help” in the app to learn more.

Precaution

• Do not disassemble the controller and the motor.

• Do not expose the product to sunlight, fire, heat, or environments where the temperature is above 60°C (140°F).

• Do not short circuit the product in any way.

• Do not crush, puncture or strike the product.

• Children under 10 years old must be accompanied by adults while playing the product.

• Children under 3 years old must not use the product, as it contains small parts that can cause suffocation.

• During charging, the battery must be placed in a well-ventilated area.

• Regularly check the charger for damages to the cord, plug, enclosure, and other parts.
  If damage is detected, stop using the charger before it’s repaired.

• Batteries are only to be charged by adults.

Declaration of Conformity

• We Beijing AIQI Technology Co., Ltd., hereby, declares that this equipment is in compliance with the applicable Directives and European Norms, and amendments.
• WEEE Disposal and Recycling Information Correct Disposal of this product. This marking indicates that this product should not be disposed of with other household wastes throughout the EU.
• To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsible to promote the sustainable reuse of materials resources.
  To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

Acceptable flexible cords for cord-connected power units

We declare that Toys is in compliance with the essential requirement and relevant provisions of Directive 2009/48/EU.
Environmentally-friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycling valuable raw materials and the treatment of toxic substances.

Troubleshooting

controller
Can’t connect via Bluetooth| The controller is off| Turn the controller on
Your phone’s Bluetooth is off| Turn on Bluetooth on your phone
Indicator light turns red after a firmware upgrade and an error the sound prompt is played| Bluetooth disconnected| Connect via Bluetooth again
The controller’s battery is low| Charge the controller
The program doesn’t run| Bluetooth disconnected| Connect via Bluetooth again
You haven’t tapped the Play button| Tap the Play button
You turned off the Programming mode| Turn on Programming mode
The indicator light doesn’t turn red when charging| The power adapter isn’t
connected properly| Connect the power adapter properly
The robot walks shakily| The robot isn’t assembled properly| Read building instructions to make sure you’ve assembled the robot properly
Can’t use the app to control the robot| Bluetooth disconnected| Connect via Bluetooth again
Can’t charge| You’re using an incompatible
power adapter| Use a compatible power adapter

Press the Reset button if you can’t solve the issues using the solutions above.

Read this manual carefully before use, and retain it for future reference.
Principal: Xiaomi Communications Со., Ltd.
Manufacturer: Beijing AIQI Technology Co., Ltd.
(a Mi Ecosystem Company)
Address: Room 1203, Block D, No. 9/11 Shangdi 3rd St., Haidian District, Beijing
This version is for private use only and should not be distributed.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>