Electus AR1940 LED Clock with Light & Wireless Qi Charger User Guide

: June 7, 2024
: Electus

Table of Contents

Function Buttons
Functions
Specification
Applicable Devices
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LED Clock with Light & Wireless Qi Charger
Model: AR1940

Function Buttons

|
---|---

Functions

A. Power Connection

Plug the USB-A end of the cable into the power adapter while plug Type-C ends into the product.
The product will be ready and stand by after all indicators are on.

B. Wireless Charging

Output: l0W
Indicator Display: Power connection successful – blue light flashes once
Standby- light off
Charging – blue light on
Charged – light off
FOD – blue light flashes continuously

C. Alarm Clock Functions

Four Buttons: Alarm,+, -, Light.
Time System Setting:
Double click the Alarm button to set up a 12-hour time system and a 24-hour time system. AM and PM will display while 12-hour time system is set.
Time Setting:

Click the Alarm button once to enter the minute setting, adjust the value with +/-;
Click the Alarm button once after the minute setting, to enter the hour the setting, adjust the value with +/-;
Click the Alarm button a third time to finish the time setting.

Alarm Setting:

Press “+”3 seconds to activate or deactivate Alarm 1; Press”-“3 seconds to activate or deactivate Alarm 2. The alarm indicator is on while the Alarm is activated;
While activated, press the Alarm button for 3 seconds to enter the alarm the minute setting, adjust the value with +/-;
Click the Alarm button once after the alarm minute setting, to enter the alarm hour setting, adjust the value with +/-;
Click the Alarm button a third time to finish the alarm time setting;
Alarm bell rings 3 minutes before automatic switch-off while no any operation.
Touch any button to enter Sleep Mode when the bell rings. Bell will ring 3 more times after 5 minutes. The indicator flashes and the Alarm button is out of function during the Sleepy Mode. If time setting is needed, please long press”+” to stop alarm 1 or long-press “-” to stop alarm 2. All buttons will function normally;
Time display brightness is automatically adjusted by 3 grades. Max brightness during 7 am-5:59 pm. Mid brightness from 6 pm to 11:59 pm. Min brightness from 12 am-6:59 am.
Time display brightness can also be adjusted manually to 3 grades (Min/Mid/Max). “+” and “-” can be used to adjust display brightness manually. The default grade is maxed brightness when power is connected. Single click”-” too dark the display one grade. The display brightness goes dark for the last grade and goes bright automatically at 7 am the next day. All manual adjustments will be synchronized to automatic adjustment.

Night Light Setting:

Night light can be set into 9 color modes: white, RGB shade, red, yellow, light green, green, light blue, blue, and pink;
Touch the Light button once to turn on the night light with white color. Another touch shall allow you to set another color in turn as specified in 5. 1). The last touch will turn off the atmosphere light.

Eco-power function:

Button cell is only for timekeeping.
All functions are out during power disconnection. Functions are restored when power is connected.

D. Note

Attention: In order to function alarm, wireless charging, night light, and USB output altogether, power shall be connected by QC2.0 or QC3.0 adapters. If connected by a 5V adapter, only wireless charging and alarm can work together.
Do not squeeze or collide.
Do not disassemble or put into the fire, water, to avoid short-circuit leakage.
Do not use wireless chargers in severe high temperatures, humidity, or corrosive environments to avoid leakage of damaged circuits.
Do not place too close to magnetic cards (ID cards, bank cards, etc.) with magnetic strips or chips to avoid magnetic card failure.
Keep more than 20cm between the implanted medical device (pacemaker, implantable cochlea, etc.) and the wireless charger to avoid potential disruption to medical devices.
Keep children from the product in case they play with the wireless charger as a toy to avoid accidents.
Keep the wireless charger and receiver device away from water and other liquids.
To clean the charger, make sure the power supply is disconnected.
Usage temperature: 0-45°C.
Usage humidity: 20-85% (40°)

Pictures in this manual are all illustrations. The final product is subject to fact.
Inside package: alarm charger, charging cable, manual.
*power adapter is not included. Please purchase otherwise or use the original phone adapter.