emporia VUE Smart Home Energy Monitor User Guide
- June 7, 2024
- emporia
Table of Contents
VUE
Smart Home
Energy Monitor
Solar Supplement
WARNING! The Emporia Vue requires installing transformers inside your
home’s electrical panel and working around the dangerous voltage that could
lead to injury or death. Emporia recommends that installation be performed by
a skilled person such as a licensed electrician or another qualified
professional in accordance with the regional electrical code where it is being
installed.
Improper installation or use of the equipment can be dangerous or even fatal.
In no event shall Emporia be liable to you or any third party for any damages,
either direct or indirect, arising from or related to any personal injury as a
result of your failure to follow the safety information and instructions in
this Installation Guide.
Note: 3.5mm and 2.5mm ports should only be used to connect the supplied
CT clamps to the energy monitor. They are not intended to carry any audio
signal.
Safety information
-
Personal protective gear should be worn when installing the Emporia Vue.
-
Do not use the Emporia Vue in any manner other than specified in this installation guide.
-
Do not attempt to open, disassemble, or repair any of the components of the Emporia Vue.
-
If you believe any of the Emporia Vue components may have been damaged, do not attempt to use them.
-
Do not install the Emporia Vue in environments with explosive gas or vapors; nor in damp or wet environments; nor in direct sunlight; nor where
temperatures are consistently below -40° F (-40° C) or above 122° F (50° C). -
Ensure the Emporia Vue does not have power during any handling, including installation and disassembly.
Need help?
support@emporiaenergy.com
1-844-EMPORIA (367-6742)
Vue solar installation
The Emporia Vue is capable of monitoring your solar production. You will install your Vue differently depending on whether your solar is a breaker- fed or a line-side tap installation. These installations are covered in the subsequent pages. If you are interested in monitoring how much energy you are pulling and sending back to the grid, you’ll need to utilize 50A CTs as described below.
Net metering
The 200A CTs that connects to your mains will provide net metering out of the
box — displaying electricity used minus electricity produced. To ensure the
Vue can correctly measure net metering, the 200A CTs must be correctly
oriented and be placed between the meter and the incoming solar.
Energy in from and out to the grid
For the Vue to be able to calculate how much energy your system is getting from and sending out to the grid, you’ll need to employ two 50A CTs on the incoming leads from your inverter. Installation depends on where these leads enter the system, which is illustrated in detail on the next two pages.
Need help?
support@emporiaenergy.com
1-844-EMPORIA (367-6742)
Breaker-fed solar installation
For breaker-fed solar installs, the 200A CTs need only to be installed between
the meter and the main breaker for net metering. To monitor how much energy is
pulling from and sending back from the grid, install a 50A CT on each of the
leads coming in from your inverter to the breaker. Ensure the
directionality of all CTs is correct.
Line-side tap solar installation
For line-side tap solar installs, the 200A CTs must be installed between the
meter and incoming feeds from the inverter. To monitor how much energy is
pulling from and sending back from the grid, install a 50A CT on each of the
leads coming in from your inverter to the mains. Ensure the
directionality of all CTs is correct.
Troubleshooting tips
If you’re not seeing net metering or grid measurements, try the following:
- Ensure the 200A CTs are clamped on the mains between the meter and incoming leads from your solar inverter.
- Ensure all CTs are oriented as per the instructions. CTs are directional.
- Check that the appropriate wiring harness wires are attached to adjacent breakers on different phases as described in the Gen 2 Vue Installation Guide.
- When configuring the Vue with the App, make sure that you temporarily turn your solar off so it is not supplying power to your system. Try running the configuration at night.
- When configuring the Vue with the App, make sure that there is a discernable load on your system. Try turning on an oven, A/C, or dryer.
Need help?
support@emporiaenergy.com
1-844-EMPORIA (367-6742)
Technical details
Energy Monitor
Energy Monitor
Power supply input:| 100-240VAC 1Ø, 50/60Hz, 0.041A
Fuse:| 260VAC/0.3A (Fusible resister: 10E, 1W, 5%, TH)
Power usage:| < 11 Watts
Wi-Fi:| 2.4 GHz 802.11b/g/n
Operating conditions:| -40° -122° F (-40° – 50° C) 0-80% RH
200A Current Transformers
Max current:| 200A
Cable length:| 1 m
Inside diameter:| 26 mm
50A Current Transformers
Max current:| 50A
Cable length:| 1 m
Inside diameter:| 10 mm
The Vue energy monitor and current transformers are considered a system designed for field installation in a switch enclosure as per section 312.8(B) of the 2017 National Electrical Code (NEC) regarding Power Monitoring Equipment. The Vue is considered a non-invasive load monitor (NILM) and as a non-permanent fixture, it is acceptable to install in an electrical panel.
The Emporia Vue Smart Home Energy Monitor contains FCC ID: 2AS6P-EMCTV2 This
device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation. This equipment complies with
FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
Caution: Any changes or modifications not expressly approved by Emporia
void the user’s authority to operate the equipment.
I.T.E. Energy Monitor
E506714
Designed in Colorado, USA. Manufactured in India.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>