MONOPRICE P/N 41710/41711 5-port/8-port Fast Ethernet Installation Guide
- June 7, 2024
- Monoprice
Table of Contents
Unmanaged Network Switch
QUICK INSTALLATION GUIDE
P/N 41710/41711 | 5-Port/8-Port Fast Ethernet
P/N 41712/41713 | 5-Port/8-Port Gigabit Ethernet
The Switch mentioned in this Quick Installation Guide stands for Monoprice 10OMbps & 1000Mbps unmanaged switches.
LED Indicators
The LED Indicators will allow you to monitor, diagnose and troubleshoot any potential problem on the switch, connection and attached devices. (Not all the LED indicators in the following table are included on one switch. Please refer to the panel of your switch)
| LED | Status | Indication |
|---|---|---|
| PWR | On | The switch is powered on |
| Off | The switch is powered off | |
| LINK/ACT | On | The port is connected to a network device |
| Flashing | The port is transferring data | |
| Off | The port is disconnected |
Troubleshooting
-
The Power (PWR) LED is not On.
• Check if the Power Adapter/Power Cord is well connected. Try to unplug and plug back in the Power Adapter/Power Cord to the switch or try another power outlet. -
The LINK/ACT LED is not On.
• Make sure the network configuration of connecting device is correct, and the network card and drivers are installed correctly.
• Check the cable connections.
• Make sure the cable distance between the switch and other IEEE802.3 compatible network devices does not exceed 100 meters. -
Performance is bad.
• Check the status of Ethernet switching. if Ethernet switching is set to full-duplex on one device but a partner is set to half-duplex, then performance will be poor.
• Make sure the cable between the switch and other IEEE802.3 compatible network devices is Category SUTP or better. -
Some devices can’t talk to other devices on the network
• Check status of the LINK/ACT LEDs to make sure devices are linked.
• Make sure that the devices’ network configurations are correct.
• Reset the switch if needed.
Need Help? We’re here for you!
Contact us: www.monoprice.com/contactus
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Modifying the equipment without Monoprice’s authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.
Warning:
[A shielded-type power cord is required in order to meet FCC emission
limits and also to prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord be used. ] [Use
only shielded cables to connect I/O devices to this equipment.]
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the
equipment.
[ ]:depend on EUT condition.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Specifications described herein are subject to change without prior
notification.
All trademarks are the sole property of their respective companies.
Copyright ©2021 Monoprice, Inc. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>