Nitecore P10iX i-Generation 217000 Flashlight Instruction Manual

Nitecore P10iX i-Generation 217000 Flashlight Instruction Manual

Battery Installation

Charging Function

Operating Instructions

Battery Installation

Insert the battery(s) as illustrated and screw to tighten the tail cap.

Note: After the battery insertion, the power indicator will flash to indicate the battery voltage. Please refer to the “Power Indication” section of this manual for more details.

Warnings:

1. Ensure the battery(s) is/are inserted with the positive end towards the The product will not work if the battery(s) is/are incorrectly inserted.
2. CAUTION! Possible dangerous radiation! Don’t look into the light! May be dangerous for your eyes.
3. When the power level is low, please stop using the product and replace or recharge the battery to prevent damage to the
4. When the product is kept in a backpack or left unused for prolonged time, please remove all batteries to prevent accidental activation or battery leakage.
5. DO NOT submerge the light into any liquid when it is hot. Doing so may cause irreparable damage to the light due to the difference of air pressure inside and outside.

Charging Function

The P10iX is equipped with an intelligent charging system. As illustrated, after inserting the battery and tightening the tail cap, use the USB cable to connect an external power supply (e.g. a USB adapter or other USB charging devices) to the charging port to begin the charging process.

• During the charging process, the power indicator will flash slowly to inform the user.
• When the battery is fully charged, the P10iX will cease the charging process and the power indicator will become steadily turned on to inform the user.
• When the light is on, connecting to a power source will automatically turn the light off. The light will return to its previous status when it is disconnected from the power source.
• The charging time for a 21700 Li-ion battery (5,000mAh) is 3 hours 45 minutes. (Charged via the 5V/2A adapter)

Tactical Momentary Illumination

Half press and hold the Power Button to turn on the light momentarily. Release to turn it off.

On / Off
On: When the light is off, press the Power Button until a click sound is heard to turn it on.
Off: When the light is on, press the Power Button until a click sound is heard to  turn it off.

User Mode Selection

The P10iX provides 2 user modes for different users and situations.

• Daily Mode (Default Setting): In this user mode, there are 6 brightness levels [TURBO, HIGHER, HIGH (850 Lumens), MID, LOW and ULTRALOW] and STROBE Mode The P10iX will memorize and re-access 5 of the brightness levels (TURBO excluded) or STROBE Mode when reactivated, unless it has been switched to the other user mode.
• Tactical Mode: In this user mode, there are only 4 brightness levels [TURBO, HIGH (850 Lumens), MID and LOW] and STROBE Mode available. The P10iX will only memorize and re-access the TURBO Level or STROBE Mode when reactivated, unless it has been switched to the other user
  Note: When using CR123/RCR123 batteries, there are 4 brightness levels [HIGH (1,060 Lumens), MID, LOW and ULTRALOW] and STROBE Mode available in Daily Mode. There are 3 brightness levels [HIGH (1,060 Lumens), MID and LOW] and STROBE Mode available in Tactical Mode.

To select a desired user mode:

1. Ensure the tail cap is fully
2. Keep holding the Mode Button (STROBE READY™) on the tail cap and the flashlight will access the TURBO Level or STROBE Mode while simultaneously loosening the tail cap.
3. Once the tail cap has been loosened, the primary white LEDs will indicate a user mode selected by flashing once for Daily Mode and flashing twice for Tactical Mode.
4. Release the Mode Button (STROBE READY™) and tighten the tail

Brightness Levels

• Daily Mode: When the light is on, short press the Mode Button (STROBE READY™) to cycle through the following brightness levels: ULTRALOW – LOW – MID – HIGH –HIGHER
• Tactical Mode: When the light is on, short press the Mode Button (STROBE READY™) to cycle through the following brightness levels: TURBO – HIGH – MID – LOW.

Momentary Access to TURBO

Daily Mode: When the light is on, press and hold the Mode Button (STROBE READY™) to access the TURBO Level (4,000 Lumens). Release to return to the previous status.

Note: When using CR123/RCR123 batteries, it will access the HIGH Level (1,060 Lumens) instead.

STROBE READY™

• When the light is off in either user mode, press and hold the Mode Button (STROBE READY™) to access the STROBE Release to turn it off.
• When the light is on in either user mode, triple press the Mode Button (STROBE READY™) to access the STROBE Short press the Mode Button (STROBE READY™) to return to the previous status, or click the Power Button to turn off the light. (This access will memorize the STROBE Mode.)
• Tactical Mode: When the light is on, long press the Mode Button (STROBE READY™) to access the STROBE Short press the Mode Button (STROBE READY™) to return to the previous status, or click the Power Button to turn off the light. (This access will not memorize the STROBE Mode.)

Power Indication

• When the battery is inserted, or the flashlight is disconnected from the power source during the charging process, the power indicator will flash to show the battery voltage (±0.1V). For example, when the battery voltage is at 2V, the power indicator will flash 4 times followed by a  1.5-second pause and 2 more flashes. Different voltages represent the corresponding remaining battery power levels:

**1×21700 battery

**

• When the light is on, the power indicator will indicate the remaining battery

1. Being steadily turned on indicates that the power is above 50%.
2. Flashing slowly indicates that the power is below 50%.
3. Flashing quickly indicates that the power is below 10%..

Note:

1. When using two CR123/RCR123 in series, the indicator will show the average voltage between the two batteries.
2. The batteries should be replaced or recharged when the output appears to be dim or the flashlight becomes unresponsive due to low power.

ATR (Advanced Temperature Regulation)

The integrated ATR technology regulates the output of the P10iX according to the working condition and ambient environment to maintain the optimal performance.

Maintenance

Every 6 months, threads should be wiped with a clean cloth followed by a thin coating of silicon-based lubricant.

Features

• Utilizes 4 x CREE XP-L2 V6 LEDs with a max output of 4,000 lumens.
• An optical system combined with crystal coating and “Precision Digital Optics Technology” (PDOT).
• Max peak beam intensity of 6,250cd and max throw of 158 meters.
• Highly efficient constant current circuit provides a stable output for up to 350 hours.
• Dual tail switches enable intuitive operations for tactical applications.
• STROBE READY™ Technology to enable a quick access to STROBE Mode (Patent ZL201320545349.4).
• STROBE Mode uses randomly changing frequencies for stronger dizzying.

effects

• Tactical Mode and Daily Mode available
• Intelligent Li-ion battery charging circuit with a USB-C port
• NITECORE 21700 Li-ion battery included (NL2150HPi 5,000mAh)
• A power indicator beside the charging port indicates the remaining battery power (Patent No. ZL201220057767.4)
• The power indicator can display the battery voltage (±0.1V)
• Incorporated Advanced Temperature Regulation (ATR) module (Patent No. ZL201510534543.6)
• Optical lenses with double-sided scratch resistant coating
• Constructed from aero grade aluminum alloy
• HA III military grade hard-anodized finish
• Waterproof and dustproof rating in accordance with IP68 (2 meters submersible) Impact resistant to 2 meters

Specifications

• Length: 137.2mm (5.40″)
• Head Diameter: 25.4mm (1″
• Tube Diameter: 25.4mm (1″)
• Tail Diameter: 28.5mm (1.12″)
• Weight: 79.5g (2.80oz)

Accessories

NITECORE 21700 Rechargeable Li-ion Battery (NL2150HPi 5,000mAh), Tactical Holster NTH10, Clip, Lanyard, Spare O-ring, CR123 Battery Magazine, USB-C Charging Cable

Battery Options

The P10iX is only compatible with NITECORE 21700 i Series batteries with an output over 15A and CR123/RCR123 batteries.

Note:

1. DO NOT attempt to use the P10iX to charge CR123/RCR123
2. The P10iX is NOT compatible with conventional 21700/18650
3. The TURBO / HIGHER Level is inaccessible when using CR123/RCR123 batteries.

Technical Data

Using a 5,000mAh 21700 Li-ion Battery

Lumens

| 1,700

Lumens

| 850

Lumens

| 300

Lumens

| 50

Lumens

| 2

Lumens

| 4,000

Lumens

*| 30min| 2h| 2h30min| 7h15min| 38h| 350h| ─
**| 158m| 102m| 72m| 44m| 17m| 3m| ─
| 6,250cd| 2,610cd| 1,280cd| 485cd| 74cd| 3cd| ─
| 2m (Impact Resistance)
| IP68, 2m (Waterproof and Submersible)

Note:
The stated data is measured in accordance with the international flashlight testing standard ANSI/PLATO FL 1-2019, using 1 x 21700 Li-ion battery (5,000mAh) under laboratory conditions. The data may vary in real world use due to different battery usage or environmental conditions.

• The runtime of TURBO is tested without the temperature regulation.

Using 2 x CR123 Batteries:

Lumens

| 300

Lumens

| 50

Lumens

| 2

Lumens

| 1,060

Lumens

| 1h| 3h 30min| 14h| 120h| ─
| 80m| 44m| 17m| 3m| ─
| 1,620cd| 485cd| 74cd| 3cd| ─
| 2m (Impact Resistance)
| IP68, 2m (Waterproof and Submersible)

Note:
The stated data is measured in accordance with the international

flashlight testing standard ANSI/PLATO FL 1-2019, using 2 x CR123 lithium batteries (1,700mAh) under laboratory conditions. The data may vary in real world use due to different battery usage or environmental conditions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>