DENVER WCS-5020 Infrared Trail Camera User Manual
- June 7, 2024
- Denver
Table of Contents
Infrared Trail Camera User’s Manual
WCS-5020
Package List:
- Camera Mounting Strap USB Cable * User Manual
Parts Of The Camera
- Display screen
- IR lamps
- Lens
- Up/Video Button
- Down/Capture Button
- Motion sensor
- OK/Shot button
- Menu Button
- Right button
- Playback button
- DC adapter port
- Tripod Slot
- Micro SD card slot
- Battery compartment
- ON-TEST-OFF button
- USB jack
Power Supply
Please install batteries before using the camera. Unlock the camera and you will find the battery compartment. Install 4 pieces of 1.5V AA batteries. Please make sure the battery polarity is correct.
Inserting the Memory Card
- Please prepare a Micro SD card and insert it into the camera for saving files. Before recording, please format the memory card first.
- You are suggested to use a micro SD card up to 32GB with class 6 or above high speed.
- To avoid malfunction, the memory card should be far away from water, strong vibration, dust, hot source, and direct sunlight.
- Do not insert the memory card forcibly. Please refer to the marking on the camera.
- For the first time of use, please wait for the memory card temperature to reach the ambient temperature. The camera will be short-circuited by environment temperature and humidity. Please protect the camera when using it outdoor.
- If the capacity of the memory card is full, the camera will stop recording automatically.
- Press the edge of the card gently to pop up the TF card.
Basic Operation
Turn On / Off the Camera
- Switch the Mode Button to “Test /On” to turn on the camera.
- Switch the Mode Button to “Off” to turn off the camera.
System Setup
Switch Mode Button to “Test”, then you can set the system parameters.
- Press the Menu button to open the setup menu.
- Press the Up/Down button to scan all menus. Then press the OK button to enter the options interface.
- Press the Up/Down button to scan all options. And press the OK button to confirm options.
- Press the Menu button again to turn back to the last menu or exit the setup menu. Following below instructions to set up the menus and functions:
Mode
Set the working mode. In photo mode, the camera just takes pictures. In
Video mode, the camera just records videos. In photo & video mode, the camera
will take a photo first, and then record a video. Options:
[Photo]/[Video]/[Photo & Video].
Photo Resolution
Set the resolution of a still image. Options: [12MP (4000x3000P)]/[8MP
(3264x2448P)]/[5MP (2592x1944P)]/[3MP (2048x1536P)]/[1MP (1280x960P)].
Photo Series
Set the photo number of continuous shootings. In photo mode, the camera will
take photos continuously. Options: [1 photo]/[2 photos in series]/[3 photos in
series].
Video Resolution
Set the video resolution. The larger the resolution is, the longer the video
time will be stored. Options: [1920x1080P]/[1280x720P]/[720x480P]/[640x480P]/
[320x240P].
TL Video Resolution
Set the resolution of a time-lapse video. Options:[2592x1944P]/[2048x1536P].
Video Length
Set the duration of recording a video clip. The shortest time can be set is 3
seconds and the longest time is 10 minutes. Options: 3 seconds~10 minutes.
Audio Recording
Access this function, the camera will record audio when recording a video
at the same time. Options: [On]/[Off].
Shot Lag
Set the time of delay shooting when the camera detects a motion. In the
selected time, the camera will not record any image or video. This function
can avoid storing too many same events and waste memory.
Options: 5 seconds~60 minutes.
IR Distance
Set the distance of infrared induction. Options: [Near]/[Middle]/[Far].
Sensitivity Motion Sensors
-
Set the sensitivity level of the sensor. Normally the
environmental impact is small indoors, you can choose “Low” sensitivity. In the normal condition of outdoor, choose “Middle”. Choose “High” if the environmental impact is huge outdoors. -
The temperature can also impact the sensor sensitivity. “High Sensitivity” should be applied to the mild environment while “Low Sensitivity” should be applied to the cold environment.
Options: [Low]/[Middle]/[High].
Target Recording Time
Set the target recording time. As shown in the below picture, you can set the
start and stop times. The camera will work just in the stated time slot. At
other times, the camera will keep in the standby state. Options: [On]/[Off].
Time-lapse
In the Time-lapse menu, there are three options as below:
[Normal]: The camera will take pictures automatically as per set time
interval. For example, set the interval time to 1 hour, the camera will take a
photo each hour. If you want to observe a plant blooms, the camera will take
24 photos in 24 hours to record the whole process of blooming.
[TL Video]: You can set the interval time within a time range to take
photos and convert these photos into a video. The time range is from 1 second
to 24 hours. For example, set the interval to 1 hour, the camera will take a
photo each hour. If the camera works for 24 hours, there will be 24 photos.
These photos will be converted into a video.
[Off]: Close the time-lapse function.
Language
Set the language display on screen. Options:
[English]/[German]/[Danish]/[Finnish]/[Swedish]
[Spanish]/[French]/[Italian]/[Dutch]/[Portuguese]/[Simplified
Chinese]/[Japanese].
Endless Capture
Set the camera to record video in loop. Options: [On]/[Off].
Time & Date
Set the date and time of the camera. Press the Right button to choose an item
and press the Up / Down button to adjust the value. And then press the OK
button to confirm.
- Options of date format: dd/mm/yyyy, yyyy/mm/dd, mm/dd/yyyy.
- Options of time format: 24h, 12h.
Options: [Set time & date]/[Time format]/[Date format].
Photo Stamp
Stamp the date & time on the photos. Options: [Time & date]/[Date]/[Off].
Password Protection
Set the power-on password of the camera. The password is four digits; each
digit can be select from 0 to 9. If you forget the password, please reset the
camera. Then all parameters will reset to the factory settings. Options:
[On]/[Off].
Beep Sound
Open/close the touch-tone. Options: [On]/[Off].
Format Memory Card
Formatting the memory card will delete all data permanently. Before using a
new memory card or a card that has been used in another device previously,
please format the memory card. Options: [Yes]/[No].
Serial No.
Set the unique serial number for the camera. The number is four digits, each
digit can be selected from 0 to 9 and A to Z. Options: [On]/[Off].
Reset Settings
Restore the camera to factory default settings including password, serial
number, and so on. Options: [On]/[Off].
Version
Look up the Firmware information of the camera.
Take Photos, Record Videos, Playback
Switch the Mode Button to “Test”. In this mode, you can take photos, record
videos, and playback files manually.
-
Take Photos:
Press the Capture button to switch to photo mode. Press the Shot button to take a picture. -
Record Video:
Press the Video button to switch to video mode. Press the Shot button to record a video clip. Press the Shot button again to stop recording. -
Playback:
Press the Playback button to enter the playback interface. Press the Up/Down button to scan photos or videos. When playback a video, press the OK button to play the video.
- Press the OK button again to pause the playback.
- Press the Menu button to stop the playback.
- Press the Playback button again to exit the playback mode. ·
- Playback Menu:
- Delete the current file: Delete the current photo or video. Options: [Cancel]/[Delete].
- Delete all files: Delete all photo and video files on the memory card. Options: [Cancel]/[Delete].
- Activate slide show: Playback the photos in slideway. Each photo displays 3 seconds. Press the OK button to stop playing.
- Write protect: Lock the file. It can avoid accidental deletion. Options: [Write-protect current file]/[Write-protect all files]/[Unlock current file]/[Unlock all files].
Working Mode
Switch the Mode Button to “On”. After turning on the camera, the screen will display 15 seconds countdown. Then the LEDs and screen will go out. The camera begins to operate independently and enter standby mode.
- If the wild animals enter the detection range of the motion sensors, the camera will be activated and detect the motion trail.
- If the wild animals continue to move to the detection zone of the sensor, the camera will take photos or record video automatically.
- When the wild animals leave the detection zone of the sensors, the camera will be deactivated and turn back to standby mode.
Night Mode
In night mode, the pictures just can display white and black. When record a
video for long time in the evening, the low voltage may have a great influence
on the stability of the machine, thus do not record video with low voltage in
the evening.
Using a Card Reader
1. Pop up the memory card from the camera and insert it into a card reader.
Then connect the card reader to a computer.
2. Open [My Computer] or [Windows Explorer] and double-click the removable
disk icon that represents the memory card.
3. Copy image or video files from the memory card to your computer.
Connecting the Camcorder to a PC by the USB Cable
- Connect the camera to the computer via a USB cable. Turn on the camera, the screen displays “MSDC”.
- Open [My Computer] or [Windows Explorer]. A “Removable Disk” appears in the drive list. Double-click the “Removable Disk” icon to view the contents from the camera.
Please notice – All products are subject to change without any notice. We take reservations for errors and omissions in the manual.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S
Electric and electronic equipment and included batteries contain materials,
components, and substances that can be hazardous to your health and the
environment if the waste material (discarded electric and electronic equipment
and batteries) is not handled correctly.
Electric and electronic equipment and batteries is marked with the crossed-out
trash can symbol, seen above. This symbol signifies that electric and
electronic equipment and batteries should not be disposed of with other
household waste, but should be disposed of separately.
As the end-user, it is important that you submit your used batteries to the
appropriate and designated facility. In this manner, you make sure that the
batteries are recycled in accordance with the legislature and will not harm
the environment.
All cities have established collection points, where electric and electronic
equipment and batteries can either be submitted free of charge at recycling
stations and other collection sites or be collected from households.
Additional information is available at the technical department of your city.
Hereby, Inter Sales A/S declares that the radio equipment type WCS-5020 is in
compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address: www.denver-
electronics.com and then click the search
ICON on a topline of website. Write model number: WCS-5020. Now enter the
product page, and a red directive is found under downloads/other downloads.
DENVER ELECTRONICS A/S Omega 5A, Soeften DK-8382 Hinnerup Denmark
www.facebook.com/denverelectronics
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>