ACU-RITE Thermometer with Wired Probe 00891W3 Instruction Manual

June 7, 2024
ACU-RITE

logo

Instruction Manual
Thermometer with Wired Probe
model 00891W3

Questions?
Contact Customer Support at 877-221-1252 or visit www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Congratulations on your new AcuRite product. To ensure the best possible product performance, please read this manual in its entirety and retain it for future reference.

Unpacking Instructions

Remove the protective film that is applied to the LCD screen prior to using this product. Locate the tab and peel it off to remove it.

Package Contents

  1. Display unit
  2. Wired temperature probe
  3. Instruction Manual

IMPORTANT
PRODUCT MUST BE REGISTERED TO RECEIVE WARRANTY SERVICE

PRODUCT REGISTRATION

PRODUCT MUST BE REGISTERED TO RECEIVE WARRANTY SERVICE
Register online to receive 1-year warranty protection www.AcuRite.com
AcuRite 13027 Intelli-Time Alarm Clock - support

Features & Benefits

FRONT

  1. Current Outdoor Temperature Temperature
    measured by the wired probe.

  2. Clock/Current Indoor Temperature & Humidity
    Displays (#4) selection.

  3. “ ” Button
    Activates momentary backlight.

  4. “ ” Button
    Toggle between current time or current indoor temperature and humidity.

  5. “C” Button Clears high/low records.

  6. ” “Button
    Press to view low temperature and humidity records.

  7. ” ” Button
    Press to view high temperature and humidity records.

  8. Wired Temperature Probe
    BACK

  9. + MINUTE Button
    Adjust minutes when in SET TIME mode (#12).

  10. Battery Compartmen t

  11. + HOUR Button
    Adjusts hours when in SET TIME mode (#12).

  12. SET TIME Switch

  13. Battery Compartment Cover

  14. °F/°C Switch
    The select temperature is degrees Fahrenheit or Celsius.

  15. Integrated Hang Hole
    for easy placement.

SETUP

Install or Replace Battery
AcuRite recommends high-quality alkaline batteries for the best product performance.
Heavy duty or rechargeable ·batteries are not recommended.

  1. Slide the battery compartment cover open and install 1 fresh “AA” battery. Follow the polarity (+/-) diagram in the ·battery compartment.
  2. Replace the battery cover.

Select Temperature Units
To select between degrees Fahrenheit (°F) or Celsius (°C) temperature units, slide the “°F/ °C” switch located inside the battery compartment located on the back of the display.
Set the Time
To set the time, slide the “SET TIME” switch to “SET TIME”. The time will now blink. Adust the hours by pressing the “+ HOUR” button. Adjust the minutes by pressing the “+ MINUTE” button. When you have reached the desired time, slide the “SET TIME” switch away from “SET TIME”.
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment that is not to be used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.

OPERATION

Placement for Maximum Accuracy
AcuRite sensors are sensitive to surrounding environmental conditions. Proper placement of both the display unit and temperature probe is critical to the accuracy and performance of this product.
Display Unit & Probe Placement
Place the display unit in a dry area free of dirt and dust. The display unit stands upright for tabletop use or is wall-mountable.
To observe outdoor temperatures, the wired temperature probe must be placed outside. The probe sensor can be securely mounted to a surface utilizing the adhesive pad or the integrated hang hole. Take care not to damage the probe during mounting.
Important Placement Guidelines

  • To ensure accurate temperature measurement, place units out of direct sunlight and away from heat sources or vents.
  • The wired temperature probe is not waterproof and is not intended for permanent submersion in liquids. Submersion in liquid for more than 30 seconds may result in the complete failure of the probe.

High & Low Records
High and low values are recorded for display (indoor) temperature and humidity and probe (outdoor) temperature. High and low records reflect the minimum and maximum temperature and humidity records in the last 24 hours. High and low records automatically reset at 12:00 am.
To view the HIGH (MAX) recorded values from the past 24 hours for temperature and humidity, press and release the ” ” button.
To view the LOW (MIN) recorded values from the past 24 hours for temperature and humidity, press and release the “ ” button.
To reset the HIGH or LOW records, press and release the “C” (clear) button while viewing the high or low records you wish to reset. Dashes will display to confirm the values have been cleared.

Troubleshooting

Inaccurate temperature

| • Make sure both the display unit and wired temperature probe are placed out of direct sunlight and away from any heat sources or vents
---|---

Display screen not working

| • Check that the battery is installed correctly. The battery may need to be replaced.

Specifications

TEMPERATURE RANGE| Display: 32°F to 122°F; 0°C to 50°C Probe: -58°F to 158°F; -50°C to 70°C
---|---
HUMIDITY RANGE|  Display: 16% ­ 98% RH (relative humidity)
 POWER|  1 x AA alkaline battery

FCC Information

TEMPERATURE RANGE

| Display: 32°F to 122°F; 0°C to 50°C Probe: -58°F to 158°F; -50°C to 70°C
---|---

HUMIDITY RANGE

|  Display: 16% ­ 98% RH (relative humidity)

POWER

|  1 x AA alkaline battery

FCC Information

This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:

  1. This device may NOT cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s).

Customer Support

AcuRite customer support is committed to providing you with best-in-class service. For assistance, please have the model number of this product available and contact us in any of the following ways:
877-221-1252
info@chaney-inst.com
24/7 support at www.AcuRite.com

► Installation Videos
► Instruction Manuals
► Replacement Parts
► Register your Product
► Support User Forum
► Submit Feedback & Ideas

IMPORTANT
PRODUCT REGISTRATION
PRODUCT MUST BE REGISTERED TO RECEIVE WARRANTY SERVICE
Register online to receive 1-year warranty protection www.AcuRite.com

AcuRite 13027 Intelli-Time Alarm Clock - support

Limited One Year Warranty

At AcuRite, we proudly uphold our commitment to quality technology. Chaney Instrument Co. warrants that all products it manufactures be of good material and workmanship and to be free of defects when properly installed and operated for a period of one year from the date of purchase.
We recommend that you visit us at www.AcuRite.com for the fastest way to register your product. However, product registration does not eliminate the need to retain your original proof of purchase in order to obtain warranty benefits.
Chaney Instrument Co. warrants that all products it manufactures be of good material and workmanship, and to be free of defects when properly installed and operated for a period of one year from the date of purchase. Remedy for breach of this warranty is limited to repair or replacement of the defective item(s). Any product which, under normal use and service, is proven to breach the warranty contained herein within ONE YEAR from the date of sale will, upon examination by Chaney, and at its sole option, be repaired or replaced by Chaney. Transportation costs and charges for returned goods shall be paid for by the purchaser. Chaney hereby disclaims all responsibility for such transportation costs and charges.
This warranty will not be breached, and Chaney will give no credit for products it manufactures which have received normal wear and tear, been damaged (including by acts of nature), tampered, abused, improperly installed, damaged in shipping, or repaired or altered by others than authorized representatives of Chaney. The above-described warranty is expressly in lieu of all other warranties, express or implied, and all other warranties are hereby expressly disclaimed, including without limitation the implied warranty of merchantability and the implied warranty of fitness for a particular purpose. Chaney expressly disclaims all liability for special, consequential, or incidental damages, whether arising in tort or by contract from any breach of this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Chaney further disclaims all liability from personal injury relating to its products to the extent permitted by law. By acceptance of any of Chaney’s products, the purchaser assumes all liability for the consequences arising from their use or misuse. No person, firm, or corporation is authorized to assume for Chaney any other liability in connection with the sale of its products. Furthermore, no person, firm, or corporation is authorized to modify or waive the terms of this paragraph, and the preceding paragraph, unless done in writing and signed by a duly authorized agent of Chaney.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For in-warranty claims: Chaney Instrument Co.
965 Wells St., Lake Geneva, WI 53147

logo
It’s More than Accurate, it’slogo
AcuRite offers an extensive assortment of precision instruments,
designed to provide you with information you can depend on to
Plan your day with confidence™.
www.AcuRite.com
©Chaney Instrument Co.
All rights reserved.
AcuRite is a registered trademark of the Chaney Instrument Co.,
Lake Geneva, WI 53147.
All other trademarks and copyrights are the property of their respective owners.
AcuRite uses patented technology. Visit www.AcuRite.com/patents for details.
Printed in China
00891W3 INST 101314

Documents / Resources

| ACU- RITE Thermometer with Wired Probe 00891W3 [pdf] Instruction Manual
Thermometer with Wired Probe, 00891W3, ACU-RITE
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals