ACU-RITE Room Monitor 00276RM Instruction Manual
- June 6, 2024
- ACU-RITE
Table of Contents
ACU-RITE Room Monitor 00276RM Instruction Manual
Questions? Contact Customer Support at 877-221-1252 or visit www.AcuRite.com.
Congratulations on your new AcuRite product. To ensure the best possible product performance, please read this manual in its entirety and retain it for future reference.
Unpacking Instructions
Remove the protective film that is applied to the LCD screen prior to using this product. Locate the tab and peel off to remove.
Package Contents
- Room Monitor
- Mounting hardware
- Instruction manual
Features & Benefits
FRONT
-
Wireless Signal Indicator
Flashes when data is being wirelessly transmitted. -
Low Battery Indicator
-
Current Indoor Humidity
Displayed when no wired sensor is attached (see page 6). -
Current Indoor Temperature
Displayed when no wired sensor is attached (see page 6).
BACK
5. Sensor Input
Plug-in for additional sensors (optional; sold separately).
6. Integrated Keyhole
For easy wall mounting.
7. Alarm “ON/OFF” Switch
For water detector (optional; sold separately).
8. Wired Sensor Retention Slot
Simplifes cord management when using add-on wired sensors (sold separately).
9. Monitor ID
Alphanumeric ID used to identify the Monitor during system confguration.
10. “ºC/ºF” Button
Select between degrees Celsius (°C) or Fahrenheit (°F) temperature units.
11. Reset Button
Resets display and sensor transmission.
12. Battery Compartment
13. Battery Compartment Cover
14. Mounting Hardware
Includes drywall anchor and screw.
SETUP
Room Monitor Setup
1 ) Install or Replace Batteries
Batteries MUST be installed for this product to operate. AcuRite recommends high quality alkaline batteries for the best product performance. Heavy duty or rechargeable batteries are not recommended.
1. Twist off the battery compartment cover.
2. Insert 2 x AA batteries into the battery compartment, as shown. Follow the
polarity (+/-) diagram in the battery compartment.
3. Replace the battery cover.
2) Write Down the Monitor’s ID
After batteries are installed, a unique 6-digit alphanumeric ID appears on the display momentarily. It can also be found printed on the back of the Room Monitor. This unique ID may be referenced for connectivity functions.
ID ——————————
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.
Placement for Maximum Accuracy
AcuRite products are sensitive to surrounding environmental conditions. Proper placement of the Room Monitor is critical to the accuracy and performance of the product.
Room Monitor Placement
The Monitor is designed for indoor use. Place the Monitor in a dry area free of dirt and dust. Monitor stands upright for tabletop use or is wall- mountable.
Important Placement Guidelines
- Monitor must be within 330 feet (100 meters) of a companion unit (optional; sold separately).
MAXIMIZE WIRELESS RANGE
Place units away from large metallic items, thick walls, metal surfaces, or other objects that may limit wireless communication.
PREVENT WIRELESS INTERFERENCE
Place both units at least 3 feet (90 cm) away from electronic devices (TV, computer, microwave, radio, etc.).
LOCATE AWAY FROM HEAT SOURCES
To ensure accurate temperature measurement, place Monitor out of direct sunlight and away from any heat sources.
LOCATE AWAY FROM HUMIDITY SOURCES
To ensure accurate humidity measurement, locate Monitor away from humidity sources. Avoid installing the Monitor near indoor pools, spas, or other bodies of water. Water sources may impact humidity accuracy.
OPERATION
Using the Room Monitor
The Room Monitor features built-in temperature and humidity sensors, to view current conditions in the location where the Monitor is placed.
Expand the System
The Room Monitor can be expanded to track additional conditions using compatible wired sensors (optional; sold separately) that simply plug into the Monitor. Wired sensors feature an extra-long cord, perfect for installing the sensors in hard-to-reach places.
When using a wired sensor with the Monitor, the Monitor’s temperature and humidity readings move to the top of the display. The display will automatically toggle between the Monitor’s temperature and humidity data, while the wired sensor’s readings appear in the middle of the display (pictured below).
Compatible digital displays, wired sensors and companion units are available at: www.AcuRite.com
Add-on Wired Sensors
Troubleshooting
If your AcuRite product does not operate properly after trying the troubleshooting steps, visit www.AcuRite.com or call877-221-1252 for assistance.
Care & Maintenance
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives.
Specifications
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the
following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user authority to operate the equipment.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation of the device.
Customer Support
AcuRite customer support is committed to providing you with best-inclass
service. For assistance , please have the model number of this
product available and contact us in any of the following ways:
24/7 support at www.AcuRite.com
► Installation Videos
► Instruction Manuals
► Replacement Parts
► Register your Product
► Support User Forum
► Submit Feedback & Ideas
Limited One Year Warranty
At AcuRite, we proudly uphold our commitment to quality technology. Chaney Instrument Co. warrants that all products it manufactures to be of good material and workmanship, and to be free of defects when properly installed and operated for a period of one year from the date of purchase.
We recommend that you visit us at www.AcuRite. com for the fastest way to register your product. However, product registration does not eliminate the need to retain your original proof of purchase in order to obtain warranty benefits.
Chaney Instrument Co. warrants that all products it manufactures to be of good
material and workmanship, and to be free of
defects when properly installed and operated for a period of one year from the
date of purchase. Remedy for breach of this warranty is limited to repair or
replacement of the defective item(s). Any product which, under normal use and
service, is proven to breach the warranty contained herein within ONE YEAR
from date of sale will, upon examination by Chaney, and at its sole option, be
repaired or replaced by Chaney. Transportation costs and charges for returned
goods shall be paid for by the purchaser. Chaney hereby disclaims all
responsibility for such transportation costs and charges. This warranty will
not be breached, and Chaney will give no credit for products it manufactures
which have received normal wear and tear, been damaged (including by acts of
nature), tampered, abused, improperly installed, damaged in shipping, or
repaired or altered by others than authorized representatives of Chaney.
The above-described warranty is expressly in lieu of all other warranties,
express or implied, and all other warranties are hereby expressly disclaimed,
including without limitation the implied warranty of merchantability and the
implied warranty of fitness for a particular purpose. Chaney expressly
disclaims all liability for special, consequential or incidental damages,
whether arising in tort or by contract from any breach of this warranty. Some
states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. Chaney
further disclaims all liability from personal injury relating to its products
to the extent
permitted by law. By acceptance of any of Chaney’s products, the purchaser
assumes all liability for the consequences arising from their use or misuse.
No person, firm or corporation is authorized to assume for Chaney any other
liability in connection with the sale of its products. Furthermore, no person,
firm or corporation is authorized to modify or waive the terms of this
paragraph, and the preceding paragraph, unless done in writing and signed by a
duly authorized agent of Chaney. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
For in-warranty claims: Chaney Instrument Co. 965 Wells St., Lake Geneva, WI 53147
It’s More than Accurate, it’s 
AcuRite offers an extensive assortment of precision instruments,
designed to provide you with information you can depend on to
Plan your day with confidence™.
www.AcuRite.com
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copy rights are the property of their respective owners. AcuRite uses patented technology. Visit www.AcuRite.com/patents for details.
Printed in China
00276 INST 052215
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>