Pandora D035 Remote Control User Manual
- June 7, 2024
- Pandora
Table of Contents
D035 REMOTE
CONTROL | TAG
The remote control is designed to control and monitor a state of a security
system at a distance of a Bluetooth connection.
ATTENTION! Enable the “Use D-030 as a radio tag” option to use the remote
control as an owner authorization device.
- OLED-display
- Three control buttons
- Built-in sound indicator (16 melodies for sound notifications)
- Built-in vibration indicator
- Built-in LED indicator “ALARM/SEND”
- 2.4 GHz radio interface (Bluetooth 5.0 protocol)
- Built-in battery
- Built-in micro-USB port
OPERATING RANGE: from -10º C to +40º C DEGREE OF PROTECTION: IP40
COMPATIBILITY
Pandora ELITE v.2, Smart Pro v.3, Camper Mini, Camper Pro v.2, Mini v.3
TURNING ON/OFF THE REMOTE CONTROL
Press and hold the button for 3 seconds to turn ON/OFF the remote control
REMOTE CONTROLLED SIGNALS MEANING
| Red indicator «ALARM» | Green indicator «SEND» |
|---|---|
| Flashes frequently if there are any notifications | Flashes if there is a |
connection with the base unit
Flashes occasionally when there is no connection| Goes dark when there is no
connection with the base unit
CHARGING THE REMOTE CONTROL
There is a battery charge level icon on the display of the remote control. It is recommended to charge the remote control if only the last segment of the icon is shown . Charge the built-in battery with a standard micro-USB cable.
FIRMWARE UPDATE
- Download the mobile application Pandora BT (Android/iOS) or Pandora Specialist (Android) to the smartphone or a tablet equipped with Bluetooth 4.0 or higher.
- Press and hold the button, connect a USB cable to the remote control, release the button after connection.
- Open the mobile application, go to the “Search device“ menu, select a found device and choose one of the update options: FILE MANAGER (only for Andriod devices) or INTERNET.
| connected
---|---
| security mode disarmed/armed
| current time
| battery charge level
| engine temperature
| interior temperature
| outside temperature
| the voltage of the car battery
| fuel level
| shock sensor (Warning level)
| shock sensor (Alarm level)
| additional sensor (Warning level)
| additional sensor (Alarm level) /Status of the original alarm system
| security zone Tilt sensor
| security zone Motion sensor
| security zone Ignition ON
| security zone Doors
| security zone Hood
| security zone Trunk
| security zone Low voltage
| security zone Brake pedal
| Engine running icon
QUICK ACCESS FUNCTIONS OF THE REMOTE CONTROL
System disarmed
| System armed (no alarm events)
---|---
Ignition ON| Ignition OFF
**(briefly)| Lock doors without arming| Arming with sound confirmation|
Search mode – Flashing hazard lights with sound signals for 5 sec
**(1 sec)| | Arming without sound confirmation| Search mode – Flashing hazard
lights without sound signals for 5 sec
(2 sec)| Hold-On ignition mode ON| |
(3 sec) **| Program neutral mode ON| | Remote engine start
(briefly)| Unlock doors| Unlock doors| Disarming with sound confirmation
(1 sec)| | | Disarming without sound confirmation
(2 sec)| Hold-On ignition mode OFF| | Switch OFF the ignition during
remote/automatic engine start, turbo timer
*(3 sec)| Service mode ON/OFF| |
(briefly)| Switch on the LCD display
(1 sec)| Unlock trunk
(2 sec)| Switch ON an engine heater
Switch ON/OFF a time channel
(3 sec)| Switch ON/OFF the remote control
+
(briefly)
| PANIC mode
****+
(briefly)
| Arming when the ignition is ON with sound confirmation| Arming in 30 sec
with sound confirmation|
****+
(1 sec)| Arming when the ignition is ON without sound confirmation| Arming in
30 sec without sound confirmation|
- To control an engine heater, it is required to make setting in Time channels:
“Select channel” – for analog control, “Action 1” – “Switch on engine preheater”