Pandora Smart v3 User Manual

June 6, 2024
Pandora

Pandora Smart v3 User Manual

Pandora Smart v3

Pandora would like to thank you for choosing our service-security system

Pandora Smart v3 is a car service-security system built for cars with on- board voltage of 12V. It
is a complex engineering solution, which includes unique and modern technological software and hardware solutions.

When building the Pandora Smart v3 we were using the most up-to-date electronics best
manufacturers. The device is built using high-precision mounting and control machinery, thus we
guarantee highest possible quality, reliability and stable technical characteristics for the whole
operation period.

The Pandora Smart v3 has a cryptographically strong authorization code with unique dialog
algorithm and individual encryption key on every device. It guarantees protection form electronic hacking for the whole operation period.

The system is built for your convenience: it’s ergonomic, reliable, has the highest security and
service characteristics, 3 years unconditional warranty and free service and support. We are happy to provide any support we can – feel free to use our online support.

! WARNING! It’s strongly recommended to install a security system by the qualified personnel!
The installer should be able to mount the system using provided documentation – installation diagram, specific installation guides and special software developed and tested by our engineers. Most of the features are depends of a correct connection and configuration of the service-security system, so if the certain feature doesn’t work as expected, most likely the problem is related to improper installation.

This device has limited external factors resistance. It should be operated in temperatures outside from -40 to +850C range. All system components must be installed only in a car interior. The base unit and radio tags fulfil with the IP40 category of protection against water.

Our web-site: pandorainfo.com
Customer support: support@pandorainfo.com

Product is in conformity with Electromagnetic Compatibility
Directive EMC 2004/108/EC and R&TTE Directive 1999/5/EC

General information

System set

  1. User manual 1.
  2. Owner’s card 1.
  3. Radio tag 2.
  4. External VALET button 1.
  5. Beeper 1.
  6. Base unit 1.
  7. Blocking relay 1.
  8. External temperature sensor 1.
  9. Wires and fastening kit 1.
  10. Wiring diagram 1.
  11. Packaging 1.

! The manufacturer reserves the right to change the system set and construction of the product to improve its technological and operational parameters without a notification.

Read before using

Carefully read this manual before starting installation and using the security-service system. Pay
attention to text marked with !

! The security and telemetric system is a complex technical product. System installation and configuration must be carried out only by a skilled professional.
! Features and system modes, control of the vehicle’s zones depends on the type of connection and system sett ings, original vehicle operation logic and trim.
! The system set includes the «Owner’s personal card». This card contains information under a protective layer that is intended only for the owner of the system. Make sure that the protective layer on the owner’s plastic card is intact after the installation of the system. Read the «Owner’s personal card» section of this manual before erasing the protective layer.
! when system installation is finished:

  • Check the system operation and functions with a specialist.
  • We recommend that you mark each working function with a sign in the «Control the system» section
  • Check that the «Installation certificate» and «Warranty card» are filled out. These documents may be required for contacting the customer support.
  • Ask an installer to mark the layout of the system components on the diagram. This information may be required for diagnostic/configuring or emergency deactivation of the system.

We recommend that you change the default value of the PIN-codes of the system. You can write down the changed PIN-codes in the «PIN-codes of the system» section.

PIN-codes of the system

FIG 1 PIN-codes of the system
The «Secret PIN-code»
(is written on the «Owner’s personal card»

The «Service PIN-code»
(default value is 1-1-1-1)

The «Guest PIN-code»
(default value is 1-2-3-4)

The «Immobilizer PIN-code»
(is used for the Validator (pin-to-drive) function)

! It is recommended that you will write down the changed or created values of all PIN-codes. Eliminate third-party access to this information

Owner’s personal card
! Erase the protective layer carefully. Do not use any sharp objects to avoid damaging of hidden information under the protective layer.

FIG 2 Owner’s personal card

The owner’s personal card contains private information under a protective layer:

  • PIN (the «Secret PIN-code») is a 4-digit number. This code can be used to disarm the system, to deactivate immobilizer functions and to activate service mode. It can be also used to enter programming mode.
  • LOGIN is a 10-digit number. This information is used to add the system to the online service and mobile applications.
  • PASS contains 8 characters and can consist of digits, lower and upper case letters). This information is used to add the system to the online service and mobile applications.
  • Phone number is a phone number of the built-in SIM-card.

External VALET button
An external VALET button with a three-color status LED indicator is placed inside a vehicle (see the system modules layout) The button is used for programing the system, arming/disarming, activating/deactivating immobilizer mode.

System modules layout

FIG 4 System modules layout

Base unit

Built-in GSM modem (2G/3G/4G LTE) provides a connection with our online- service pandora-on.com and mobile application Pandora Connect, voice and SMS notifications, automatic date and time detection, allows to control the system by a phone using DTMF-commands. The modem operates in a mobile network using the nano-SIM.

Built-in slot for a nano-SIM used for owner’s SIM-card
Built-in GPS/GLONASS-receiver is designed to determine current location and to automatically
determine UTC date and time.
2.4GHz radio channel, Bluetooth 4.2 protocol (BLE 4.2) supports up to 15 additional Bluetooth devices (see the «Additional devices» section), including a mobile phone.

Built-in 3D accelerometer is used to detect shock/motion/tilt including 2 separate zones of shock sensor (alarm and warning), the system allows to adjust sensitivity of each zone, to use data from the accelerometer to block the engine and close the central lock on movement.

Temperature sensors allow the system to measure temperature of different zones to send this
information to the mobile apps. The following zones are available: interior temperature – built in sensor of the main unit, engine temperature – external temperature sensor (see the «System set»), outside temperature – digital car protocol*.

The system setting allow you to reassign sensor to different zones and use information from external additional devices (PS-331BT, RHM-03 BT, DMS-100 BT); to implement automatic engine or engine preheater starts and stops by temperature.

*Built-in digital 2хCAN/LIN interface** allows the system to read the statuses, execute commands via digital buses and also to control a pre-heaters such as Webasto Thermo Top Evo и Eberspacher Hydronic 1/2/3.

**Built-in IMMO-KEY port and immobilizer bypass*** – hardware and software algorithms with the special «Pandora CLONE» server which are allow to bypass a vehicle’s immobilizer system for automatic and remote engine start.

Built-in micro-USB port – update and configuration of the system using a PC and Pandora Alarm Studio or mobile app Pandora Specialist.

! *More information is available on loader.pandorainfo.com.

Information signals of the system

FIG 5 Information signals of the system

FIG 6 Information signals of the system

FIG 7 SOUND AND LIGHT SIGNALIZATION

FIG 8 BEEPER SOUND SIGNALS

SYSTEM FUNCTIONS AND MODES

Security mode

FIG 9 Security mode

Security and monitored zones

  • Interior temperature (status)
  • Engine temperature (status)
  • Outside temperature (status)*
  • Voltage of the on-board circuits (status)
  • Engine operation control – RPM (status)
  • Heater operating control (status)
  • Fuel level (status)
  • Parking (automatic gearbox) /Handbrake (manual gearbox) status
  • «Parking light is not turned off» notification (status)
  • Shock sensor (security zone – alarm and warning level)
  • Motion sensor (security zone – alarm level)
  • Tilt sensor (security zone – alarm level)
  • OE alarm system status via CAN, additional sensor (status, security zone – alarm and warning level)
  • Turning ignition on (status, security zone – alarm level)
  • Opening doors (status, security zone – alarm level)
  • Opening a trunk (status, security zone – alarm level)
  • Opening a hood (status, security zone – alarm level)
  • Pressing brake (status, security zone – alarm level)

!*Outside temperature is available by an additional device (see the «Additional devices» section) or by CAN -bus data (see loader.pandorainfo.com).

Remote and automatic engine starts

The system allows for remote engine start using the «remote engine start» command from the
mobile application or preconfigured automatic engine start function. Remote start can be used to heat engine and interior, charge battery or to cool the interior with air conditioning.

Remote and automatic starts can only be used when the system is armed. While the system is in
remote or automatic start mode, it keeps performing all security functions of all of the security zones excluding a shock sensor (the system can be configured to not disable the shock sensor during a remote engine start). To compensate it, the motion sensor sensitivity and responsiveness will be increased. If any security zone will be triggered, the engine will be immediately stopped and alarm mode will be triggered.

When using the remote and automatic engine start functions, make sure that a car is secured with handbrake or some other means of fixating the car on a parking position. Remote and automatic engine start on automatic transmission cars will only occur, if a transmission selector lever was left in the «P» position.

If a car has manual transmission, remote or automatic start will only occur if the program neutral
procedure was followed when the car was arming.

AN EXAMPLE OF THE «PROGRAM NETURAL» PROCEDURE

  1. When the engine is running, fixate the car with the handbrake and put gear lever to the neutral position. Program neutral procedure will be switched on automatically (by default system settings).
  2. Turn the key in the ignition lock to the OFF position (the engine should still be running) and take it out of the lock (skip this step for cars with a Start/Stop button).
  3. Leave the car, close the doors.
  4. Arm the system – the engine will be stopped. Now the system is ready to perform remote and automatic engine start.

Automatic starts
The system allows configuring automatic engine start and stop conditions. Automatic starts can be configured using the internet-service or mobile apps. The following conditions can be specified for automatic engine starts: schedule, time period, engine temperature, voltage. The engine will be stopped automatically after specified time or when the engine temperature reaches a specified value.

The engine can be also stopped by a user command.

! Automatic engine starts and stops by temperature are available only if a temperature sensor is connected. Remote and automatic engine starts are not available if the hood is open. After third failed consecutive attempt of automatic start all subsequent automatic starts will be cancelled until arming/disarming of the car (it doesn’t affect at remote start feature).

Slave mode
This mode allows arming and disarming using original vehicle control – an original key, button/sensor of a keyless access entry system.

Slave mode can be implemented using analog connections or a digital protocol of a vehicle

! This mode is disabled by default for a digital protocol. More information on loader.pandorainfo.com. It is recommended to activate the «Prohibit disarming when a tag is absent» to increase security features of the Slavemode.

Owner authorization devices and functions

Authorization devices
Authorization devices are Bluetooth devices paired with the system (radio tags, remote control
D030, mobile phone with the app). The devices are used to recognize an owner in the radio
coverage zone of the base unit to arm/disarm the system (Hands Free mode) and to implement
immobilizer or Anti-Hi-Jack functions.

! Install the beeper if you use authorization devices.

FIG 10 Hands Free mode

Immobilizer mode
This mode is used to recognize an owner using authorization devices when the system is disarmed. When turning on the ignition, the base unit performs a search for authorization devices in the radiocoverage zone. If there is no any authorization device in the radio coverage zone, the system will block the engine. Engine blocking will occur immediately or at the time a motion sensor detects movement, it depends on the system settings. When an authorization device appears in the coverage zone, the system will exit blocking mode and will continue to work in normal mode.

! This mode is enabled by default. It is required to make additional connections for this mode.

ANTI-HI-JACK-1/2 modes
The Anti-Hi-Jack modes help to prevent aggressive seizure of a vehicle when authorization in case of disappearance of authorization devices from the radio coverage zone when system is disarmed.

ANTI-HI-JACK-1 mode – The base unit checks if an authorization device is in the radio coverage zone each time when ignition is on and a door is opened/closed.

ANTI-HI-JACK-2 mode – The base unit constantly checks if an authorization device is in the radio coverage zone when ignition is on.

If the system cannot detect an authorization device, the base unit will perform a delayed engine
blocking. The siren will play the «Engine blocking warning» ringtone before blocking. The engine will be blocked immediately or at the time the car starts moving, it depends on the system settings. When an authorization device appears in the coverage zone, the system will exit blocking mode and will continue to work in normal mode.

! This mode is disabled by default. This mode can be set only by a professional specialist.

Multi-button code immobilizer (pin-to-drive)
Multi-button code immobilizer (pin-to-drive) is a function that allows disarming, disabling blocking and controlling service mode and time channels using original vehicle controls (button, lever or pedal) and a pre-programmed PIN-code (the «Immobilizer PIN-code»).

AN EXAMPLE OF USING THE FUNCTION

  • Turn on the ignition to disable engine blocking or enable service mode, turning on the ignition is not required if you want to disarm the system or control time channels.
  • Enter the «Immobilizer PIN-code». Press a programmed button/lever/pedal the number of times equals to the first digit. Pauses between presses should not exceed 1 second. More than 1 second pause will be interpreted as the start of the next digit input. The immobilizer code can consist max of 4 digits from 1 to 9.
  • The system will confirm the correct input by a sound signal of the beeper and a programmed function will be performed.

! This mode is disabled by default. This mode can be set only by a professional specialist.

Checking the number of paired devices

The number of paired radio tags/mobile device can be checked by the number of flashes of the LED indicator. The number of tags/mobile device can be checked when switching on the ignition (the system must be disarmed). The number of green flashes will indicate the number of paired radio tags, a following red flash will indicate a paired mobile device.

FIG 11 Checking the number of paired devices

IMMOBILIZER RADIO TAG

FIG 12 IMMOBILIZER RADIO TAG

Functions of the button

Functions of the button

Light indication of SEND LED

FIG 14 Light indication of SEND LED

Replacing an immobilizer tag battery
When replacing the battery you must carefully follow the following steps:
Carefully open the cover of the tag’s battery compartment (fig.1). Extract discharged battery and
insert a new one keeping in mind the correct polarity (fig.2). Replacing a battery will not cause a loss of tag code information, as authorization data is stored in the non-volatile memory of the MCU. Carefully close the cover of the tag’s battery compartment. All elements of construction should be rigidly locked in places.

If it is so, the tag can be operated as usually.

FIG 15 Replacing an immobilizer tag battery

Updating firmware of the tag

  • Download the Pandora BT application (for Android or iOS devices equipped with a Bluetooth 4.0 Low Energy or higher module).
  • Open the mobile app Pandora BT.
  • Press and hold the button of the radio tag until the 10th flash of the SEND indicator, then release the button.
  • Select the found device and select one of the update option: FILE MANAGER – firmware will be uploaded from the phone storage (only for Android). INTERNET – firmware will be uploaded by an internet connection.

CONTROL THE SYSTEM BY A PHONE

! For the correct operation of the GSM functions, an owner should monitor the status/balance of the SIM card installed in the system. If the SIM card is blocked or defective, GSM functions of the system will be unavailable. Call the system’s phone number. When it answers, enter a command code.

FIG 16 CONTROL THE SYSTEM BY A PHONE

*It is required to enter the «Secret PIN-code» after dialing a command

DTMF commands
For example: To have simple access to engine start function, create a new contact in the contact list of your phone, name it «Engine start», for instance, and add the number in the following format:

+XXXXXXXXXXX,123,297
where
«+XXXXXXXXXXX» – the system phone number,
«,» – pause is a feature of the phone (can be displayed as the «P», see the instructions of the phone), «123» – remote engine start DTMF command,
«297
» – end call DTMF command.
Contact can be added as a speed dial to any of the free button.
To have simple access to engine start function a phone other than the main owner’s phone, create contact in the following format:
+XXXXXXXXXXX,1234,123,297
where «1234» – guest PIN-code.

Activate/Deactivate service mode

  1. Call the system number. Wait for the answer.
  2. Turn on the ignition, an authorization device (a radio tag, a Bluetooth remote control, a paired mobile phone with the app installed) must be in the coverage zone, enter the «Immobilizer PIN-code» (if the «Code immobilizer» function is enabled).
  3. To activate service mode, dial the 551 DTMF command — «Activate service mode», then enter the «Secret PIN-code» from the owner’s personal card.
    To deactivate service mode, dial the 552
    DTMF command — «Deactivate service mode».

Voice help
The system has a voice help menu. During a voice call to the system, dial 9* and listen to the
information about system control commands.
To end the session, hang up the phone.

Repeat the last message
To repeat any message, press* during a voice call to the system.

Arming/Disarming

  1. Call the system number. Wait for the answer.

  2. Dial 1 to arm, and 0 to disarm.
    For silent arming dial 10 or 00 for silent disarming.

  3. The system will confirm arming/disarming.
    To end the session, hang up the phone.

Enabling/disabling automatic engine starts
Pandora systems have a function of prompt disabling automatic engine start:

  1. Call the system number and wait for the answer.
  2. Dial 987 to disable all automatic engine starts or 789 to enable.
  3. The system will confirm execution of the command.

To end the session, hang up the phone.
Automatic starts can be enabled again by dialing 789* (all previous settings will remain intact).

Request current coordinates

  1. Call the system number. Wait for the answer.
  2. Dial 500*.
  3. The system will confirm: «Current coordinates are sent via text message» and will send a message with LBS and GPS/GLONASS coordinates at your phone.

To end the session, hang up the phone.

Request GSM balance

  1. Call the system number. Wait for the answer.
  2. Dial 100*.
  3. The system will confirm: «Balance information is sent via text message» and will send text message with account balance information to your phone.
    To end the session, hang up the phone.

Tow truck mode
This mode is intended for car transportation with preservation of arming function. Tow truck mode can be activated only when the system is armed, it will be deactivated automatically when disarming.

  1. Call the system number. If the system is in PANIC mode, receive an emergency call. Wait for the answer.
  2. Dial 15* , to enable the «Tow truck» mode, the system will disable motion, shock and tilt sensors. To end the session, hung up the phone.
  3. To disable this mode, disarm the system.

Activating/Deactivating engine blocking
You can block a car engine using any phone. The engine will remain blocked until phone command «Unlock engine» will be sent and the «Secret PIN-code» will be entered. This blocking cannot be disabled by any other means.

  1. Call the system number and wait for the answer.
  2. Dial 666 to block an engine or 999 to unlock it (after dialing 999* you should enter the «Secret PIN code» that is located on the owner’s card).

! All other commands can be entered in the same manner.

Changing settings via a phone
Disarm the system, call the system number, wait for the answer, switch on the ignition for 1-3
seconds (but no more than 5 seconds), then switch it off. The system will enter the settings mode.
An example of changing the owner’s system number:

  1. Enter the setting menu via a phone according to the instruction above;
  2. Dial DTMF command 1(phone number settings) and 1(owner’s system number);
  3. Enter new owner’s number in the format XXXXXXXXXXX # (the system recognizes «» as «+»);
  4. To confirm, dial 1*.

! There are 2 ways to change main owner’s phone number

  1. Via a phone, using DTMF commands sett ings mode.
  2. Using radio tags: turn on the ignition when the system is disarmed and call the system phone number. Wait for the answer, dial the «Guest PIN-code» (default value is 1-2-3-4) if you are calling not from the main owner’s number, then press and hold the butt on on the radio tag for 2 seconds (until the second flash of the SEND indicator). Release the butt on, the system will recognize the incoming phone number as the «Main owner’s phone number».

FIG 17 CONTROL THE SYSTEM BY A PHONE

FIG 18 CONTROL THE SYSTEM BY A PHONE

ONLINE SERVICE AND MOBILE APPLICATION

Telemetric function of the system allows you to control your vehicle using the online service pandora-on.com or mobile app – Pandora Connect (for iOS/Android). The Pandora Connect application can work via a Bluetooth channel. To get these functions, the mobile phone must be paired with the system.

FIG 19 ONLINE SERVICE AND MOBILE APPLICATION
! For the correct operation of the GSM functions, an owner should monitor the status/balance of the SIM card installed in the system. If the SIM card is blocked or defective, GSM functions of the system will be unavailable.

Before using the online-service, It is required to create an account (Registration), login to your account (using your email and password created on the registration step) and add the system to your account (enter information from the «Owner’s personal card»).

Registration
Visit the website or open the mobile app to create an account.
Web-service: https://pandora-on.com
«Pandora Connect» mobile app is available in appropriate stores:

App Store for iOS devices;
Google Play for Android.

FIG 20 Registration

! Minimum requirements for mobile devices: Android v5.0; iOS v13.0.
The manufacturer reserves the right to make changes to the design and functionality of the Internet service and mobile application without notifying the consumer.

You will create the data to sign in: LOGIN – your email, PASSWORD – a password entered during the registration. You will receive an email with a confirmation link. Click the link to complete the registration procedure.

Login
After completing of the registration process, youcan login to the online service via a computer’s web browser or via the mobile app Pandora Connect. Use your previously created login/password to login.

Adding a system to your account
The created account can support up to 3 telemetry systems. Use the information from the «Owner’s personal card» to add the system to your account.
Go to the «Add a device/Add a system» window and enter the LOGIN and PASS from the «Owner’s personal card», create a name for your car and click «Add».

! Erase the protective layer carefully. Do not use any sharp objects to avoid damaging of hidden information under the protective layer. After this, you will be able to control, change sett ing and get information about the vehicle state through the online-service.

! Number of events in the history is limited. Events are stored for at least one month.

Control via Bluetooth
The Pandora Connect application can work via a Bluetooth channel when there is no connection to the server. This type of connection allows you to control the system, receive status information and use your mobile phone as an authorization device.
To get access to these functions, pair a mobile device in the system:

I. ENTER THE PROGRAMMING MODE
Use the VALET button to enter the «Service PIN-code» (default value is 1-1-1-1). See the detailed instruction of code entering in the «Control the system in case of emergency» section.

II. ENTER THE «PAIRING A MOBILE PHONE» PROGRAMMING LEVEL
After entering programming mode, press and hold the VALET button for 5 seconds (until the fifth signal of the Siren/Beeper»). The system will enter the «Pairing a mobile phone» programming level. The LED indicator will light green, the system is ready for pairing.

! The previously paired device will be erased from the system memory after entering the level.

III. PAIR A MOBILE PHONE.
Turn on Bluetooth on your mobile phone, open the settings of the application. Go to «Bluetooth control», tap «Not specified», select the detected system in the search window. The system will confirm pairing with the series of green and red flashes of the LED an a sound signal of the siren.

! If there is no automatic pairing, enable the «PIN request for phone pairing» item in the «Radio tag and mobile device functions» sett ings and make the pairing procedure again. A mobile device will request a PIN -code (Factory pre-set is 0-0-1-1-1-1 where 4 last digits are the «Service PIN -code».

IV. EXIT PROGRAMMING MODE
Turn on the ignition and then turn off to exit programming mode.

! The system supports only one mobile device.

CONTROL THE SYSTEM

Arming

FIG 21 CONTROL THE SYSTEM

FIG 22 CONTROL THE SYSTEM

Disarming

FIG 23 Disarming

FIG 24 Disarming

Locking/unlocking doors when ignition is on

FIG 25 Disarming

PANIC mode

FIG 26 PANIC mode

Remote engine start

FIG 27 Remote engine start

FIG 28 Remote engine start

FIG 29 Remote engine start

Service mode
It is recommended to put the system into the service mode before handing it to a car service or valet parking. When this mode is switched on, security system stops interfering with built-in electronics and disables all functions to ease maintenance.

To switch on this mode, disarm the system, turn on the ignition, an authorization device (a radio tag, a Bluetooth remote control, a mobile phone) must be in the coverage zone, enter the «Immobilizer PIN-code» (if the «Code immobilizer» function is used) and use one of the method described below:

FIG 30 Service mode

FIG 31 Service mode

CONTROL OF THE SYSTEM IN CASE OF EMERGENCY

The system has emergency ways to deactivate security and Anti-hi-Jack functions (using the VALET button and the «Secret PIN-code») in case of loss or failure of control devices or in case of discharge of a battery (when you cannot replace it or charge).

Before using emergency system control, check the system and vehicle control devices: check a
battery, turn on a device in accordance with its manual (if required).

If all devices are working, try to make a primary vehicle diagnosis: check the vehicle original control device, vehicle battery charge level, gearbox selector position, check information on the dashboard.

! The system can be controlled from a phone using DTMF commands.
0 – Disarming.
998
xxxх – Deactivate authorization devices (Immobilizer and Anti-Hijack functions), where хххх is the «Secret PIN-code» written on the Owner’s personal card under the protective layer.
1– Arming.
888
– Activate authorization devices (Immobilizer and Anti-Hi-Jack functions).
! Read the procedure for entering the PIN-code before using emergency functions.

ENTERING THE PIN-CODE
The code must be entered only when the base unit is powered and the ignition is off. The PIN-code can be entered using the external or located on the base unit VALET button. The digits input and correct input is indicated by the external or located on the base unit LED indicator.

  • Enter the first digit • Press the button the number of times equal to the first digit. Pauses between presses should not exceed 1 second. Each pressing will be confirmed with an orange LED indicator flash. Pause for more than 1 second, a red LED indicator flash and a short sound single of the Beeper confirm the input of the first digit. Then you can enter the next digit.
  • Enter the second digit • Press the button the number of times equal to the second digit. Pauses between presses should not exceed 1 second. Each pressing will be confirmed with an orange LED indicator flash. Pause for more than 1 second, a red LED indicator flash and a short sound single of the Beeper confirm the input of the second digit. Then you can enter the next digit.
  • Enter the third digit • Press the button the number of times equal to the third digit. Pauses between presses should not exceed 1 second. Each pressing will be confirmed with an orange LED indicator flash. Pause for more than 1 second, a red LED indicator flash and a short sound single of the Beeper confirm the input of the third digit. Then you can enter the next digit.
  • Enter the fourth digit • Press the button the number of times equal to the fourth digit. Pauses between presses should not exceed 1 second. Each pressing will be confirmed with an orange LED indicator flash. The correct input will be confirmed with the series of green and red flashes of the LED indicator.

Emergency disarming
In case you cannot disarm the system as usual, use the VALET button and the «Secret PIN-code» written on the Owner’s personal card (see the «General information» section):

  • If your car is locked, unlock it by an original key. Not paying attention to the siren signals, make sure that the ignition is off and enter the «Secret PIN-code» (see the procedure description above). If there are no siren sounds or LED flashes, check the battery. It is not possible to enter the «Secret PIN-code», if there is no power supply.
  • The system will be disarmed in case of correct PIN-code input. It will be confirmed with the series of green and red flashes of the LED indicator, the series of sound signals of the Beeper, 4 beeps of the Siren and 4 signals of the light signalization.
  • The system will stay in previous state in case of incorrect input of the PIN-code. It will be indicated with a long red flash of the LED indicator. New input can be attempted after 5 seconds.
  • Emergency disarming is equivalent to a normal method of disarming. No additional actions are required for further operation of the system.

Emergency control of the anti-theft functions
This section describes how to deactivate and activate anti-theft functions (Immobilizer and Anti-Hijack), which use a radio tag, a remote control or a mobile phone as an owner authorization device, and «Code immobilizer» function, which uses standard car controls (buttons, levers, pedals) to enter the Immobilizer PIN-code.

Emergency deactivation of anti-theft functions
To temporarily deactivate the Immobilizer or Code immobilizer function (pin- to-drive), turn on the ignition when the system is disarmed. Enter the «Secret code» from the owner’s personal card using the VALE T butt on. The immobilizer functions will be being deactivated by the time the ignition is turned off.

Emergency activation/deactivation Immobilizer/Code Immobilizer functions
А еmergency control of the anti-theft functions is possible only when the system is disarmed, the ignition is off, service mode is deactivated, a vehicle battery is charged.

Enter the «Secret PIN-code» or the «Service PIN-code» (default value is 1-1-1-1) to put the system in programming mode.

Pauses between presses should not exceed 1 second. Each pressing will be confirmed with an
orange LED indicator flash. The system will confirm entering the 13th or 15th level with the red flashes of the LED and short signals of the Siren/Beeper.

  • TO DEACTIVATE THE FUNCTION – The LED indicator will be green after entering the programming level. The system will wait 10 seconds for entering the «Secret PIN-code». If the PIN-code is not entered within 10 seconds or the input is incorrect, the siren will sound one signal, the LED will produce the series of red and green flashes and the system will return to the programming menu. Enter the «Secret PIN-code» that is written on the owner’s plastic card. The system will confirm deactivating with two sound signals of the siren, a long red LED flash and two sound signals of the siren. Turn on the ignition and then turn off to exit programming mode. The function will be deactivated.
  • TO ACTIVATE THE FUNCTION – The LED indicator will light red and the Beeper will sound a long beep after entering the programming level. The system will wait for action. Press the VALET button once activate the immobilizer function. The system will confirm enabling with one short sound signal of the Siren/Beeper and a green LED light. Turn on the ignition and then turn off to exit programming mode.
    The function will be activated.

ADDITIONAL DEVICES

Remote control D-030 is a two-way short-distance communication device designed to control a security system and receive information about its state. The remote control can be used as an owner authorization device.

FIG 32 Remote control D-030

CONTROL COMMANDS
Arming/Disarming | Trunk | Remote engine start | Engine pre-heater
STATUSES Vehicle and system statuses

OWNER AUTHORIZATION
Immobilizer | Anti-Hi-Jack | Hands Free
OLED-display | 2.4GHz radio interface (BLE 4.2) | Three control butt ons |
Sound indicator | Vibro indicator | LED indicator| Battery | micro-USB

Radio tag BT-760 / BT-770 – is a one-way short-distance communication device designed to control a security system. The tag can be used as an owner authorization device.

FIG 33 ADDITIONAL DEVICES

CONTROL COMMANDS
Arming/Disarming | Service mode | «Hold On» mode

OWNER AUTHORIZATION
Immobilizer | Anti-Hi-Jack | Hands Free
2.4GHz radio interface (BLE 4.2) | Control butt on | LED indicator | Motion sensor | CR 2032 battery

Door sensor DMS-1OO BT is a wireless device designed to monitor internal or external perimeter state: any security zone can be assigned to the Hall/shock/tilt sensor state; temperature monitoring. The sensor can be installed on a door, hatch, trunk, trail, garage door.

2.4GHz radio interface (BLE 4.2) | Hall sensor | Temperature sensor | Shock/
tilt sensor | CR123a battery

Radio module RHM-03 BT – is a wireless device designed to control equipment of the engine compartment:

  • Control of Hood lock, siren, engine blocking based or not based on car movement, digital control of engine pre-heaters Eberspacher and Webasto;
  • Statuses of temperature, engine pre-heater, Trunk security zone.
    2.4GHz radio interface (BLE 4.2) | Built-in relay (NC) | Motion sensors | Trunk switch input | External temperature sensor | Outputs: siren, hood lock | Engine pre-heaters (LIN)

Piezo siren PS-331 BT is a wireless device for sound indication and control of engine compartment:

  • Control connection with the base unit;
  • Temperature sensor, «Trunk» security zone. Sound pressure 118 dB | 2.4GHz (BLE 4.2) Radio interface | flexible input «Trunk» | Flexible output | Temperature sensor

Blocking radio relay BTR-101 is a wireless device designed to perform blocking engine blocking based or not based on car movement.
2.4GHz (BLE 4.2) Radio interface | Built-in-blocking relay (NC/NO) | Motion sensor

WARRANTY OBLIGATIONS

Manufacturer guarantees correct operation of the service-security system if exploitation,
installation, storage and transportation conditions described in this manual were met.
The system should only be used according to installation scheme and user manuals.
The system is meant to be installed by the professional car electronics installers. The installer should fill in installation certificate that is included in this manual.
Parts malfunctioning during warranty period on the fault of the manufacturer should be repaired
or replaced by the installation center of the manufacturer or by certified service center. List of certified service centers can be found on pandorainfo.com

The user loses the right for warranty services in the following cases:

  • when warranty period expires;

  • if exploitation, installation, storage or transportation conditions were not met;

  • if there is mechanical damage of the external parts of the system after it is sold.
    This includes: fire damage, consequential damage in case of car accident, aggressive liquids and water seeping damage, damage caused by improper use;

  • if the damage was caused with incorrect settings and parameter adjustment;

  • if system devices are replaced with any devices that are not recommended by the manufacturer;

  • if manufacturer sealing is broken;

  • if there is no properly filled warranty card and installation certificate.

Warranty period is 3 years since the moment of purchase, but no more than 3.5 (three and a half)
years since the moment of production. This warranty does not include batteries of the remotes, as they have their own service lifetime.

Maintenances and repairs of the system with expired warranty period are carried out at the expense of the user on a separate contract between the user and the installer/service center.

! We recommend that you ask an installer to fill out the installation certificate and the warranty card. These documents may be required for contacting the customer support..

INSTALLATION CERTIFICATE

FIG 38 INSTALLATION CERTIFICATE

FIG 39 INSTALLATION CERTIFICATE

ACCEPTANCE CERTIFICATE

FIG 40 ACCEPTANCE CERTIFICATE

WARRANTY CARD

FIG 41 WARRANTY CARD

Read More About This Manual & Download PDF:

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals