Intertek Bonaire Durango 3100 Portable Evaporative Cooler Owner’s Manual
- June 7, 2024
- Intertek
Table of Contents
- IMPORTANT
- Disclaimer
- General Safety Information
- Product Description
- Unpacking
- Product Specifications
- Electrical Connection and Installation
- Operation
- Maintenance
- Wiring Diagram
- How to change controller batteries
- Troubleshooting
- Supplier’s Declaration of Conformity
- Warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Evaporative Air Cooler
Bonaire Durango 3100
Owner’s Manual
DO NOT return to store
For help with installation or warranty issues
Call:800-939-2983 or
Visit: www.bonaire-usa.com
For parts, visit our secure website:
www.bonairedurango.com
IMPORTANT
READ AND SAVE THESE INSTRUCTIONS.
Please keep this important manual in a safe place.
It is the owner’s responsibility to ensure that regular maintenance is carried
out on this evaporative cooling product. Failure to do so will void all
guarantees beyond statutory and legal requirements.
Disclaimer
Climate Technologies reserves the right to make alterations to specifications, quantities, dimensions etc. for production or other reasons, subsequent to publication. While we believe the information is accurate and complete, we make no warranty or representation for any particular purposes. The information is offered in good faith and with the understanding that any use of the units or accessories in breach of the directions and warnings in this document is at the sole discretion and risk of the user.
General Safety Information
Thank you for purchasing a quality Bonaire Evaporative Portable Cooler. We
care about your safety and would ask you to spend a few minutes reading these
simple instructions before operating this product.
Safety!
Read carefully prior to attempting to assemble, install, operate or
maintain the unit.
– Read and save these instructions. Do not throw these instructions away
– Complete the unit assembly before attempting to operate.
– Interference with and operation of this cooler in any manner not prescribed
by these
instructions could cause a safety issue and WILL void any warranty.
WARNING:
– Do not use a cooler on uneven or unstable surfaces.
– Do not overfill. Use water only.
– Do not operate cooler with Rear Filter Panel removed.
– Do not insert any foreign objects or body parts into the air inlet or
outlet, otherwise bodily injury or property damage may occur.
– Do not use immediately adjacent to heat sources such as stoves or radiators.
– Do not use immediately adjacent to sources of water, such as swimming pools,
hot tubs, bathtubs, showers, sinks, or other liquids.
– Do not operate this product near an open flame or the product may ignite and
cause fire, resulting in bodily injury or property damage.
– Do not operate in areas where gasoline, paint, or other flammable liquids or
vapors are used or stored.
WARNING:
– All electrical connections must comply with local construction and safety
regulations and be performed by qualified personnel.
– The power cord should be connected directly to a 120VAC +/-10%, 60 Hz, 1
phase only grounded GFCI protected electrical receptacle. Make sure that the
power switches are in the off position before connecting and operating your
cooler.
– Do not use this product with any solid-state speed control device.
– Keep the cord away from heated surfaces.
– Do not operate a cooler with a damaged cord, plug, or other components.
– Do not step on or roll over the power cord with heavy or sharp objects.
– Do not run the power cord under the carpet or other floor covering. Arrange
cord away from traffic area and where it will not be tripped over.
– Do not use the power cord with an adaptor plug that converts the 3-pin plug
into a 2prong connector.
– If the power cord is damaged, it should be replaced by a service agent or
qualified personnel to avoid risk of bodily injury or property damage.
– Remove the plug from the electrical receptacle by pulling on the plug and
not the cord.
– Use only qualified electricians for replacement or servicing of switches or
electrical motors and components in this cooler.
– If damaged, discard cooler or return to an authorized service facility for
examination and/or repair.
WARNING:
– Always unplug the power cord from the wall outlet receptacle when the air
cooler is not in use, before adding water, before cleaning, before removing
the cooling pad, before
maintenance and replacing parts, or before moving to another location.
– Do not plug the cord into an electric outlet with wet hands or an electric
shock may result. The same applies for unplugging.
– Never wash the unit cabinet with a garden hose. water may harm the motor and
electrical system.
– Never attempt to disassemble or alter the product in any way not instructed
by this manual. Shock, fire, or bodily injury may occur.
– Do not allow children to operate or service this cooler.
WARNING:
Stagnant water may cause bacterial growth and serious health problems. Do not
allow stagnant water to remain in the tank.
– Drain and clean the water tank before storage, after seasonal use and
whenever the unit is not in daily use.
Product Description
The Evaporative Air Cooler is an efficient, energy-saving product. It cools by
combining water evaporation with air movement, through carefully designed and
manufactured equipment, providing maximum efficiency and safety.
The evaporative cooling technology is very economical and gives a number of
additional benefits compared to traditional air conditioning systems for homes
and businesses. The system does not use refrigerants or compressors; it cools
by simply moving air through a surface composed of specially designed
evaporative cooling pads.
The heat from the inlet air is absorbed by the water. The resulting outlet air
temperature drops when the water transforms into gas. Humidity is not
perceived, since the air in the room is renewed approximately every two
minutes, while a comfortable cooling effect is created. Continuous air
circulation is a vital aspect of the evaporative cooling process used in this
equipment and gives it a distinct advantage over air conditioning by
refrigeration.
Unpacking
Handle the unit with care. Visually inspect for shipping damage. If any part is damaged, immediately file a claim with the carrier.\
Product Specifications
Model | Bonaire Durango 3100 |
---|---|
Voltage | 120 VAC, 60 Hz, 1 phase |
Amperage | 1.9A |
Tank Capacity | 15 gal (57L) |
N.W. | 28.7 lbs (13kg) |
Dimensions: inches (cm | H: 44” (111.7 cm) X W: |
24.8” (63.0 cm) X D:
17.6” (44.7 cm
Afloat valve facility is available in this model. This feature makes provision
for automatic water filling of the cooler. Ensure proper connection of water
inlet pipe into the float valve to avoid leakage.
Note: Maximum water inlet pressure 29 psi (200 kPa)
Electrical Connection and Installation
Review and understand the warnings in the General Safety Information section, pages 2 & 3.
-
Wheel Installation:
Insert all the five small wheels into the round holes at the bottom.
-
Install the cooler on a flat, level surface.
-
Adjustable Up and Down louver: The Up and Down Louvres can be adjusted using the protruded tab shown on Page 5.
-
Add clean water into the water tank. Check the water level window on the front of the cooler to see when the water tank is full.
-
Plug the unit into a 120 VAC (± 10%) 60 Hz, 1 phase GFCI protected grounded outlet.
Operation
Control Panel & Remote Control
- POWER (ON/OFF ) [ ****]: Press this button to switch the cooler on/off. The icon will glow with blue color at ON position and RED color at OFF position.
- COOL [ ]: Press the button to switch the pump ON/OFF. Cool Icon will glow when switched ON. The pump will start only when there is sufficient water in the tank, indicated by the water icon glowing in WHITE. A low water level will be indicated by a buzzer for 5 seconds and the water icon will start blinking in red color.
- FAN [ ]: When started, the fan icon will glow. Press the button for High, Medium, and Low speeds. The selected speed will be indicated by a glowing LED.
- SWING [ ]: Press the button to switch the swing function on/off. The swing icon will glow when switched ON.
- TIMER [ ]: Press the button to set OFF timer to 1-7 hours in intervals of 1 hr. The timer icon will glow when the timer is switched ON and the glowing LEDs will indicate the total of time setting.
- WATER LEVEL: The LED light is white when the tank contains enough water to operate in cool mode. When water is lacking in the tank, the LED light is red, and the cooler sounds an alarm for a
short period. During cooling mode, if water depletes and triggers the alarm,
add water to the tank through the “front water inlet”, and press the COOL
button to turn the cooling function on again.
REMOTE CONTROL (Batteries not included): Open the battery compartment at
the back of the remote control and insert two new AAA dry cell batteries. Care
must be taken to insert the batteries into the correct polarity (+/-) markings
shown inside the battery compartment.
Air Renewal Requirements:
When your cooler is working, it is important to leave a window or door open in
order to keep a constant airflow and to avoid any accumulation of humidity and
heat. Your Evaporative Cooler does not cool correctly when airflow is
restricted from exiting a room. This causes a decrease in the cooling
efficiency due to an increase of humidity. Therefore, an opening of at least 1
square foot for every 500 CFM of injected air is required.
Maintenance
WARNING
Stagnant water may cause bacterial growth and serious health problems. Do
not allow stagnant water to remain in the tank.
Drain and clean the water tank before storage, after seasonal use, and
whenever the unit is not used for a long time period.
Changing the filter pads:
Please follow the instructions below in order to change the filter pads.
-
Remove the top screw (under the power cord). Remove the two screws on the bottom of the filter pad retainer.
-
Lift the top panel enough so that the filter pad retainers can move out.
-
The filter pads are secured in place with two brackets on top and bottom. Remove the four screws to be able to remove the filter pads.
-
Remove and replace the filter pads.
-
Assemble in reverse order, ensuring the panels are fitted correctly with no gaps or tabs left outside.
Wiring Diagram
How to change controller batteries
- Press pad with thumb and slide battery cover off.
- Remove old batteries and insert new batteries according to the orientation shown on the controller.
- Slide the cover back into position, while pressing the pad.
WARNING
A. Do not mix old and new batteries.
B. Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cad, NiMH,
etc) batteries.
Troubleshooting
Problem | Reason | Solution |
---|---|---|
No airflow | 1. Power is not connected. |
2. Power is not turned ON.
3. Body damaged.| 1. Plug in the power cable properly. 2. Press the AirSpeed
button to start. 3. Return to Service Center.
Abnormal Sound| 1. Foreign article inside the body of the unit.
2. Loose air fan.
3. Motor defect.| 1. Remove the rear cover and wet pad, remove foreign
particles.
2. Return to Service Center.
3. Return to Service Center.
No evaporation/Cooling| 1. Water tank is clogged. 2.0ther cause.| 1. Clean
the water tank.
2. Return to Service Center.
Airflow direction cannot be controlled| The swing motor is defective.| Return
to Service Center
Supplier’s Declaration of Conformity
a. This device complies with part 15 of the FCC rules.
b. Responsible supplier listed as per SDoC:
Bonaire USA LLC.
Contact 800-939-2983 or www.bonaire-
usa.com
Warranty
Statement on Product Warranty (U.S.A.)
-
Warranty
Subject to the Conditions and Exclusions, Climate Technologies Pty Ltd provides the original purchaser with the following warranty:
Climate Technologies Pty Ltd warrants these appliances: Bonaire Durango 3100, for a
(2) two-year period (parts only) from the date of purchase. During this period, a defective appliance or defective parts will be repaired or replaced free of charge at the election of Climate Technologies Pty Ltd. In addition, the Lifetime cabinet corrosion parts only warranty on the unit cabinet applies.
Climate Technologies Pty Ltd makes no warranties, representations, or promises as to the quality or performance of its evaporative coolers other than those specifically stated in this warranty. -
Conditions and Exclusions
a) The warranty only covers portable coolers manufactured by Climate Technologies Pty Ltd and purchased in the U.S.A.
b) The warranty does not cover installation components that may be attached to the product manufactured by Climate Technologies Pty Ltd. These may include and is not limited to items such as ducting, flues, grills, piping, etc. These items remain solely the responsibility of the installer/owner.
c) This warranty is only valid if the appliance is installed and operated in accordance with the manufacturer’s instructions and for its designed and intended purpose at the nominating phase, voltage, and frequency.
d) Product fitness for purpose and overall system design/sizing are solely the responsibility of the installer/owner. This includes but is not limited to heat load calculations, airflow, system balancing, humidity, water quality, etc.
e) Industrial or commercial use of this product will void the warranty. The appliance is designed for domestic use only.
f) The product must be installed by a qualified person in the manner prescribed by local and statutory regulations and to the manufacturer’s specifications.
g) Warranty will only be given where proof of purchase is provided by the original purchaser and Climate Technologies Pty Ltd is satisfied that the appliance is within the warranty period.
h) Warranty will not be provided where, in Climate Technologies Pty Ltd opinion:
i. There is nothing wrong with the appliance.
ii. The defective operation of the appliance is due to the failure of electricity or water supply.
iii. Defects are caused by neglect, incorrect application, abuse, normal wear and tear or by accidental damage of the appliance.
iv. An unauthorized person has attempted to repair the appliance.
v. The appliance has been changed or modified in any way.
vi. A situation arises referenced in the trouble-shooting guide.
i) Damage caused by elements such as wind, rain, lightning, floods, etc. along with power spiking and brownouts are not considered defective material or workmanship and as such are not covered by our warranty.
j) If there is no certificate of compliance for plumbing or electrical work, Climate Technologies Pty Ltd reserves the right to refuse a warranty on non- compliant installations.
k) No responsibility will be accepted for outside elements such as pests, animals, pets, and vermin that may cause damage to the unit.
l) Harsh environmental situations such as salt air that may cause damage are not covered.
m) Responsibility or liability is not accepted for damage to contents, carpet, walls, ceilings, foundations, or any other consequential loss or damage of whatever nature either direct or indirect resulting from installation, operation, or misuse of the appliance.
n) Parts replaced under warranty are warranted for the balance of the original Warranty Period.
o) All warranties are non-transferable.
p) The benefits conferred by this warranty are in addition to warranties and other rights in respect of the appliance, which the consumer has under State and Federal laws. This warranty must be read subject to that legislation and nothing in this warranty has the effect of excluding, restricting, or modifying those rights. -
How to obtain service
Subject to the aforementioned conditions and exclusions, Climate Technologies Pty Ltd will repair or replace (at its discretion) any evaporative cooler which, after examination, is determined to be defective for the duration of warranty delineated in the “Warranty” section. Bring the evaporative cooler in need of service to the nearest authorized retailer special service desk. A copy of proof of previous replacement must also be included if applicable. Maintain the original documents for future reference.
The authorized retailer and Climate Technologies Pty Ltd will assess your product and provided paperwork to confirm the 1-year limited warranty is still valid. If any items n the “Conditions and Exclusions” section are found, then the 1-year limited warranty is null and void. A valid, legible product serial code must also be visible to obtain service under the Climate Technologies Pty Ltd evaporative cooler 1-year limited warranty. If the authorized retailer and Climate Technologies Pty Ltd deem that a product cannot be serviced and a replacement is necessary, a similar product of equal or greater value will be shipped to you free of charge by Climate Technologies Pty Ltd. -
Climate Technologies Pty Ltd
Climate Technologies Pty Ltd is a company incorporated in Australia (A.C.N. number 001 418 042). Reference to Climate Technologies Pty Ltd includes its authorized distributors.
Warranty for Replacement Parts.
Parts replaced under warranty are warranted for the balance of the Cooler’s original warranty period.
Proof of Purchase
Please attach your proof of purchase here. Your receipt is your warranty and will be required to validate any warranty.
Dealer / Product Information
Dealer/Retailer:|
---|---
Address:|
Phone Number:|
Unit Model Number:|
Serial No:|
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN
IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY CLIMATE TECHNOLOGIES
PTY LTD EVAPORATIVE COOLER PRODUCT. DETAILS OF THIS LIMITED WARRANTY ARE
SUBJECT TO CHANGE WITHOUT NOTICE. IF YOU DO NOT AGREE TO THIS CONDITION, YOU
SHOULD NOT PURCHASE THE PRODUCT. IN NO VENT SHALL CLIMATE TECHNOLOGIES PTY
LTD BE LIABLE FOR ANY INCIDENTAL, SPEC AL, CONSEQUENTIAL OR PUNITIVE DAMAGES,
OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES, OR DELAYS ALLEGED TO BE AS
A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT
INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OR PROFITS. SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS
EXCLUSIVE AND IN LIEU F ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL. TO THE
EXTENT PERMITTED BY AW, CLIMATE TECHNOLOGY ES PTY LTD DISCLAIMS ANY IMPLIED
WARRANTIES, INCLUDING WITHOUT LIMITATION, AN IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SU H
DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE
DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU. THIS WARRANTY IVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
www.bonairedurango.com
References
- Bonaire Durango - Sustainably Cooling Your World Since 1954
- Bonaire Durango - Sustainably Cooling Your World Since 1954
- Bonaire Durango - Sustainably Cooling Your World Since 1954
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>