Skullcandy S2TVW SeshEvo True Wireless In-Ear Earbuds User Guide

June 7, 2024
Skullcandy

Skullcandy logo USER GUIDE

Skullcandy S2TVW SeshEvo True Wireless

Auto Pair Mode

Skullcandy S2TVW SeshEvo True Wireless -figPairing Mode

Auto Power- On

Skullcandy S2TVW SeshEvo True Wireless -fig1

power-On

Auto Power -Off

Skullcandy S2TVW SeshEvo True Wireless -fig2

Power-Off

Charge Earbuds

Skullcandy S2TVW SeshEvo True Wireless -fig3

Charge Earbuds

Charge case

Skullcandy S2TVW SeshEvo True Wireless -fig4 Charge case

Pairing Mode

∗Off ModeSkullcandy S2TVW SeshEvo True Wireless -fig5Pairing Mode

**Pair New Device

**

“Sesh Evo”Skullcandy S2TVW SeshEvo True Wireless -fig6

Power -On

Left Side and Right Side
Skullcandy S2TVW SeshEvo True Wireless -fig7

Power-Off
Skullcandy S2TVW SeshEvo True Wireless -fig8

Play/Pause
Skullcandy S2TVW SeshEvo True Wireless -fig 9

**Track Forward

**

Right Side
Skullcandy S2TVW SeshEvo True Wireless -fig10

Track Back

left Side

Skullcandy S2TVW SeshEvo True Wireless -fig12

Volume Up

Skullcandy S2TVW SeshEvo True Wireless -fig13

Volume Down

Skullcandy S2TVW SeshEvo True Wireless -fig14

Answer/End
Left Side or Right Side

Skullcandy S2TVW SeshEvo True Wireless -fig18

**Activeate Voice Assistant

**

Left Side or Right Side
Skullcandy S2TVW SeshEvo True Wireless -fig15

**Clear Paired Device

**

Left Side or Right Side
∗Off Mode
Skullcandy S2TVW SeshEvo True Wireless -fig16

Rest Device

**Tile™ Enabled:

**

Download the App

Skullcandy S2TVW SeshEvo True Wireless -fig17

Download the Tile™ App

Pair Tile™Skullcandy S2TVW SeshEvo True Wireless
-fig17

Skullcandy S2TVW SeshEvo True Wireless -fig18

**3EQ Mode

**

Left Side or Right
Music, Move, and Podcast

Skullcandy S2TVW SeshEvo True Wireless -fig19

Change equalizer modes

Speaker Driver: 6mm, Impedance: 32 Ohms, THD <3%@1 KHz, Voltage Regulation: 5V, 500mA, Bluetooth® 5.0, Frequency Band: 2402MHz – 2480MHz, Maximum Power: 10mw, Weight: 63.5g.
Skullcandy and other marks are registered trademarks of Skullcandy, Inc. All rights reserved.
Maximum operating temperature 45°C.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

ISED Compliance Statement

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1 )This device may not cause interference. (2)This device must accept any interference, including interference that may cause undesired operation of the device.

ISED SAR Compliance Statement

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End-user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value is reported under this standard during product certification for use when properly worn on the body.

Americas
Skullcandy, Inc.
6301 N Landmark Dr.
Park City, UT 84098 U.S.A.
Skullcandy.com| Canada
Skullcandy Canada ULC
329 Railway St. Unit 205
Vancouver, BC. V6A 1A4 Canada
Skullcandy.ca
---|---

Contains a Li-ion battery. The battery must be recycled or disposed of properly.
Hardware Version: V5.1
Software Version: V5.0
Made in China.
MODEL: S2TVW
FCC ID: Y22-S2TVW
IC: 10486A-S2TVW

R-Sku-S2TVW
018-200004

Questions Vist: www.skullcand.com

Skullcandy S2TVW SeshEvo True Wireless -icon634

Skullcandy S2TVW SeshEvo True Wireless -icon6547

Skullcandy S2TVW SeshEvo True Wireless -icon64

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals