Weego 44.1 12-Volt Portable Lithium Jump Starter User Guide
- June 6, 2024
- Weego
Table of Contents
JUMP STARTING
POWER PACK 44
QUICK START GUIDE
Model No. 44.1
GETTING TO KNOW WEEGO 44
CHARGE UP YOUR WEEGO 44
When you unpack your new Weego 44 for the first time, charge it up to 100%
with either the wall or car charger provided. Remember to recharge your Weego
44 every 6 months, even when you’re not using it it will help extend its
lifespan.
POWERING ON/OFF
There’s a Power ON/OFF Button on the back of your Weego 44. While powered
“ON”, the blue power button will remain illuminated. Make sure you turn OFF
your Weego 44 after every use; leaving it on slowly drains the battery.
Indicator Lights Sequence: 100% Charged 80% Charged 60% Charged 40% Charged
20% Charged
It takes 3 hrs. to fully charge. The indicator lights will flash one by one
while the unit is charging. A solid light indicates a completed level of
charge.
JUMP STARTING
BEFORE YOU JUMP
Read all instructions and safety information prior to using this product. Improper use of this product will void your warranty and may result in product damage, excess heat, toxic fumes, fire, and other unsafe conditions for which Weego is not responsible.
Read vehicle owner’s manual first: it may have specific cautions and instructions about jumping your engine.
This product is for use on 12V Lead-Acid batteries only! DO NOT use this product on any other voltage battery, such as 6V, 24V, etc. DO NOT use this product on lithium-ion batteries.
Never jump an engine in an enclosed area.
Put your vehicle in PARK and engage the emergency brake (boats and powersports’ vehicles should be put in NEUTRAL).
TURN OFF ALL ELECTRONICS! air conditioner, radio, lights, etc.
Remove any devices attached to your Weego 44.
Never leave your Weego 44 connected to your engine’s battery unless actively jumping.
**** Always disconnect the Smarty Clamps® from your Weego 44 when not in use.
WEEGO CUSTOMER SUPPORT We are dedicated to providing the best possible service. To reach Weego Customer Support, visit myweego.com/support or email support@myweego.com.
|
---|---
Connect Clamps
| Power ON
|
Attach Black (-), Then Red (+)
|
When You Have FLASHING GREEN LIGHT On Your Smart Box, Start Your Engine
|
Once it Starts, Disconnect Clamps from Weego 44|
Detach Clamps From Battery
JUMP STARTING YOUR ENGINE
- Ensure your engine is completely OFF.
- Securely connect the Smarty Clamps® to your Weego 44, then power ON.
- Attach BLACK clamp to your battery’s negative (-) terminal, then the RED clamp to your battery’s positive (+) terminal. Adjust your Smarty Clamps® to achieve MAXIMUM contact with the terminals. Poor connections will prevent you from starting your engine! Clear off any dirt or build-up with a wire brush or a dry towel before connecting your clamps.
- Place your Weego 44 in a secure location or suspend using the provided hook & lanyard so it won’t fall. Check your Smarty Clamps® lights.
- When you have a FLASHING GREEN READY light, start your engine. If the engine doesn’t start, turn off your vehicle and check your Smarty Clamps® lights.
- After a successful start, quickly disconnect the Smarty Clamps® from your Weego 44.
- Detach the Smarty Clamps® from the battery.
- You’re now good to go – be sure to run your engine for at least 15 minutes before shutting it off again so it has time to recharge your battery.
If you are having issues getting your engine started, see the Troubleshooting section in your quick start guide, owners manual or on myweego.com for further details and assistance.
WARNING! Exposed Metal Jaws May Be HOT After Use!
UNDERSTANDING YOUR Smarty Clamps®
Your Smarty Clamps® have a “smart” box that will help guide you through a jump
with both sight and sound. It will let you know when it is safe to jump or if
there is an error.
TROUBLESHOOTING
Visit www.myweego.com/support for FAQs and additional troubleshooting inquiries and details.
My unit won’t power on/charge/charge past a few lights
If your unit won’t power on, won’t take a charge OR won’t charge past a few
lights then it’s been overdischarged. This can happen if the unit is left ON,
or if an engine pulled the Weego battery past a certain limit during a jump
start.
Please reach out to support@myweego.com to let them know about this issue we’ll receive and test the overdischarged Weego, then determine if we can repair it or if it needs to be fully replaced.
The Weego won’t jump start my vehicle
A few things can attribute to a failed jump start, which we listed below.
- Poor connection between the Weego clamps and vehicle battery: the better the connection, the more likely you are to have a successful jump
- Dirty battery terminals: build up prevents all the available power from reaching your battery
- Vehicle-specific compatibility issues: occasionally we come across a vehicle that has unique power demands that a smaller model cannot fulfill, even though it’s within our recommended engine range. In addition, vehicles with heavier electronics can sometimes create issues when jumping with a Weego; we mostly see this in push-to-start vehicles.
- Cold temperatures: Freezing temperatures create a lot of resistance in an engine which means it can require up to 3.5X the usual amount of power to get started; for example, an engine that usually needs 200A could need up to 700A in the extreme cold. In addition, if your Weego was stored in the cold temps it will make it harder for the Weego to deliver its full power.
- Low-Charged Weego: it’s always best to work with full power on your Weego if you can. Our jump starters perform better at 100% charge than they do at 20% charge, especially when jumping larger engines.
USB CHARGING
Charge your phone, tablet and other portable devices with your Weego 44 using
your own USB charging cord. Your Weego 44 comes equipped with Detect-o-MaticTM
USB Charging. This intelligent charger communicates with your device to detect
and deliver the fastest-possible charge.
To charge your devices, plug your charging cord into your Weego 44 USB port
and connect to your device. Power on your Weego 44 and start charging!
LIGHTING
Your Weego 44 comes with a 500 lumen LED flashlight. Power on your Weego 44,
then briefly press and release the flashlight button to initiate the following
sequences:
- 1st click: Normal
- 2nd click: Strobe
- 3rd click: SOS
- 4th click: OFF
You can also skip directly to the OFF position by holding down the flashlight button.
Your Weego 44 will give you up to 14 hours of flashlight time and up to 28 hours of strobe & SOS light on a full charge.
© 2020. Weego is a division of Paris Corporation. US Patent #9692155,
D823243. All Rights Reserved. Rev 06/20 myweego.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>